Regency E33-NG LOG Installation, Final Installation, 03-23, 03-22 03-18 03-24 03-20 03-19 03-17

Page 10

INSTALLATION

5)Place the top bracket onto the top edge of 10) Install the 2 brick retaining clips, one on

the top panel (refer to Diagram 2).

each side.

Top Bracket

Diagram 2

6)Slide the top panel and bracket assembly carefully onto the bafﬂe plate ensuring the panel is centered. Make sure the tabs of the topbracketﬁtintothebafﬂeopenings(refer to Diagram 3).

Final Installation

		03-23
03-22	03-18	03-24
03-22	03-18

03-20

03-19 03-21

03-17

The "03" reference numbers (i.e. 03-23) are molded into the rear of each log.

Instructions:

1)Remove and carefully unwrap the logs from the box. Please handle with care and do not force them into position to avoid chipping.

2)Remove the top louver and ﬂ ush door if installed (refer to page 14).

3)To remove the grate, loosen the two Phillips screws which are securing the grate. Slide the grate outwards to remove it from the unit (refer to Diagram 1).

Screws

Diagram 3

7)Insert the back panel by sliding it between the sidewalls of the ﬁ rebox and the rear log support.

8)Before installing the side brick panels, re- move the screws from the side brick clips (refer to Diagram 4).

Diagram 4

9)Insert the side panel by positioning it ﬂ at against the side walls. Tilt the panel towards the middle of the ﬁrebox, then insert the bottom front corner. Repeat on the other side.

LOG INSTALLATION

WARNING: Dangerous operating condi- tions may occur if these logs are not positioned in their correct certiﬁed locations. Read the following instruc- tions carefully and refer to the attached diagram.

Materials Required:

Complete Log Set (Part # 340-930) Contains the following:

	Description
03-17	Bottom Log
03-18	Center Top Log
03-19	Front Log
03-20	Left Log
03-21	Right Log
03-22	Left top Log
03-23	Rear Log
03-24	Right Top Log

Diagram 1

4)Angle log 03-17 and slide it between the top and bottom burner tube under the “T” section until it touches the left grate support bracket (refer to Diagram 2).

03-17

Diagram 2

10	E33 FPI Direct Vent Gas Insert

Image 10

Contents E33 Gas Insert 08/16/05FPI GAS Fireplace Insert E33 FPI Direct Vent Gas InsertTable of Contents Safety Label Installation Materials Required Installation ChecklistMinimum Fireplace Opening Minimum Fireplace Opening Excalibur OptionMinimum Clearances to Combustibles GAS Connection Flue Liner InstallationVenting GAS Pipe Pressure TestingDiagram Optional Brick Panel03-23 LOG InstallationFinal Installation 03-22 03-18 03-24 03-20 03-19 03-1703-23 03-20 Locating Pins Locating PinsLocating Pins 03-20 03-24 03-23 Locating Pins 03-21Shut off the gas supply Remove the louvers and ﬂ ush door E33 Conversion KIT from NG to LPGConversion Kit Contains Qty Burner Oriﬁce RemovalRear View Faceplate Assembly Diagram Faceplate & Trim InstallationPilot Adjustment Screw Rear View Trim Assembly DiagramFull Screen Front Flush LouversStandard Flush Door To remove the ﬂ ush door, reverse the above stepsOrder to make the following wire connec Install Spring Hinges to the Left and RightSide of the bottom of the ﬁ rebox using Rebox and connect them to the switchOptional Screen Doors Accent KIT InstallationAttach door bracket to sides using 4 screws Double Screen Door attach to left and right side of unitOptional Remote Control Optional Wall Wiring DiagramThermostat Operating Instructions Copy of Lighting Instruction Plate Normal Operating Sounds GAS AppliancesMaintenance Fan Access Plate Screws FAN MaintenanceStraighten adjustment wire Door GlassInstall new gasket and valve assembly Valve AssemblyRebox and from the valve access plate Replacing fanParts List Main AssemblyBurner Assy NG/LP Burner & LOG AssemblyValve Tray Burner Grate AssyFull Screen Front Installation FACEPLATES, Trims and Hearths E33 FPI Direct Vent Gas Insert E33 FPI Direct Vent Gas Insert E33 FPI Direct Vent Gas Insert E33 FPI Direct Vent Gas Insert Warranty ConditionsInstaller Please complete the following information E33 FPI Direct Vent Gas Insert