Regency E33-NG, E33-LP installation manual Flush Louvers, Standard Flush Door, Full Screen Front

Page 14

INSTALLATION

10)Attach the faceplate panels to the insert body using the 4 remaining black screws. Refer to Diagram 5.

Securedoorbyfasteningwithtwoscrewslocated at bottom of glass frame (refer to Diagram 1).

To remove the fl ush door, reverse the above steps.

FLUSH LOUVERS

1)The top louver is held in place by friction fi t. Refer to Diagram 1

Diagram 5

11)Push the FPI logo plate into the two holes in the bottom left corner of the faceplate.

STANDARD

FLUSH DOOR

The standard flush door comes with a black frame. To install the frame, simply hook the top door fl ange onto the top of the unit and swing the door towards the unit, (Diagram 1 and 2). Be careful that the glass gasket does not roll up; there must be a gap between the gasket and the door lip to ensure that the door sits securely on the unit. Refer to Diagram 3.

Diagram 1

Screws

Diagram 1

2)Install the Spring Hinges on the left and right side of the bottom of the Firebox using 2 screws per hinge.

3)Place the Bottom Louver near the hinge. Flip hinge over the Bottom Louver and secure using 3 screws.

Hinge

Location

Bottom Louver

2)Lift the unit up slightly and push down on the corners of the Bottom Trim Bracket and slide under unit.

Push in Corners

Bottom Trim

Bracket

3)Completely secure faceplate to the unit by securing 4 screws to the Left and Right Side Trim.

Diagram 2

Diagram 3

FULL SCREEN FRONT

1)Hold the full screen faceplate up against the unit in order to make the following wire connections.

Pull the ON/OFF connector wires thru the box and connect them to the switch.

Connect the fan switch wires with the wire connectorsfromthefanspeedcontrol.Place clips over wires and tuck into side trim.

4)Install the Top Frame by hooking it onto the two screws at the top of the full screen door. It is held in place by magnets.

Screw

Top Frame

14

E33 FPI Direct Vent Gas Insert

Image 14
Contents E33 Gas Insert 08/16/05FPI GAS Fireplace Insert E33 FPI Direct Vent Gas InsertTable of Contents Safety Label Installation Materials Required Installation ChecklistMinimum Fireplace Opening Minimum Fireplace Opening Excalibur OptionMinimum Clearances to Combustibles Venting Flue Liner InstallationGAS Connection GAS Pipe Pressure TestingDiagram Optional Brick Panel03-23 LOG InstallationFinal Installation 03-22 03-18 03-24 03-20 03-19 03-1703-23 03-20 Locating Pins Locating PinsLocating Pins 03-20 03-24 03-23 Locating Pins 03-21Shut off the gas supply Remove the louvers and fl ush door E33 Conversion KIT from NG to LPGConversion Kit Contains Qty Burner Orifice RemovalRear View Faceplate Assembly Diagram Faceplate & Trim InstallationPilot Adjustment Screw Rear View Trim Assembly DiagramFull Screen Front Flush LouversStandard Flush Door To remove the fl ush door, reverse the above stepsOrder to make the following wire connec Install Spring Hinges to the Left and RightSide of the bottom of the fi rebox using Rebox and connect them to the switchOptional Screen Doors Accent KIT InstallationAttach door bracket to sides using 4 screws Double Screen Door attach to left and right side of unitThermostat Wiring DiagramOptional Remote Control Optional Wall Operating Instructions Copy of Lighting Instruction Plate Normal Operating Sounds GAS AppliancesMaintenance Fan Access Plate Screws FAN MaintenanceStraighten adjustment wire Door GlassInstall new gasket and valve assembly Valve AssemblyRebox and from the valve access plate Replacing fanParts List Main AssemblyBurner Assy NG/LP Burner & LOG AssemblyValve Tray Burner Grate AssyFull Screen Front Installation FACEPLATES, Trims and Hearths E33 FPI Direct Vent Gas Insert E33 FPI Direct Vent Gas Insert E33 FPI Direct Vent Gas Insert E33 FPI Direct Vent Gas Insert Warranty ConditionsInstaller Please complete the following information E33 FPI Direct Vent Gas Insert