Regency E33-LP, E33-NG installation manual Faceplate & Trim Installation, Pilot Adjustment Screw

Page 13

INSTALLATION

“Maintenance Instructions” (page 20) for correct fl ame patterns.

18)Check inlet (12” WC min) and outlet (11” WC) pressures. Refer “Gas Pipe Pressure Testing” (page 9).

19)Check operation of fl ame control.

20)Check for proper fl ame appearance and glow on logs.

Pilot

Adjustment

Screw

Diagram 1

WARNING:

This conversion kit shall be installed by a qualified service agency in accordance with the authority having jurisdiction. If the infor- mation in these instruction is not followed exactly, a fire, explosion or production of carbon monoxide may result causing prop- erty damage, personal injury or loss of life. The qualified service agency is responsible for the proper installation of this kit. The installation is not proper and complete until the operation of the converted appliance is checked as specified in the manufacturer’s instructions supplied with the kit.

Note: Equipped for Altitude 0-4500 ft. (0-1370m).

Installer Notice:

These instructions must be

left with the appliance.

FACEPLATE & TRIM

INSTALLATION

1)Lay the faceplate panels fl at, face down on something soft so they don't scratch.

2)Take the top faceplate and align the holes in it with the holes in the side panels. Us- ing the screws provided, attach from the top of the panel (the holes in the top panel are slightly larger than the holes in the side panel to facilitate easier installation). Refer to Diagram 1.

Hint: Don't tighten the screws down com- pletely at this point, continue on with steps 3 and 4 and do a trial fi t to the unit. Make any necessary adjustments and when it fi ts properly then tighten down the screws.

Rear View: Faceplate Assembly

Diagram 1

3)Using the connectors provided, join the left side trim (with the ON/OFF switch) to the top trim. Diagram 2. Connect the right side trim to the top trim.

Rear View: Trim Assembly

Diagram 2

4)Place the trim on the assembled faceplate panels, aligning the wire connections from the switches with the notch on the left side panel.

5)Connect the fan switch wires by taking the black and red wires with the male ends (in the grey harness) and connect them with the wire connectors from the fan speed control.

6)Connect the ON/OFF switch wires by taking the black and red wires with the female ends and connect them to the ON/OFF switch.

7)Tuck the wires into the faceplate to keep them away from the insert using the clip provided. Attach the clip to the rear of the faceplate to ensure that the wires do not touch the side of the unit. Refer to Diagram 3.

8)The power cord should be run behind the faceplate panel.

Diagram 3

9)Attach the trim to the faceplate by using the plated screws (refer to Diagram 4).

Diagram 4

E33 FPI Direct Vent Gas Insert

13

 

Image 13
Contents 08/16/05 E33 Gas InsertE33 FPI Direct Vent Gas Insert FPI GAS Fireplace InsertTable of Contents Safety Label Installation Minimum Fireplace Opening Installation ChecklistMaterials Required Minimum Fireplace Opening Excalibur OptionMinimum Clearances to Combustibles GAS Connection Flue Liner InstallationVenting Diagram Pressure TestingGAS Pipe Optional Brick PanelFinal Installation LOG Installation03-23 03-22 03-18 03-24 03-20 03-19 03-17Locating Pins 03-20 Locating Pins03-23 03-20 Locating Pins 03-24 03-23 Locating Pins 03-21Conversion Kit Contains Qty E33 Conversion KIT from NG to LPGShut off the gas supply Remove the louvers and fl ush door Burner Orifice RemovalPilot Adjustment Screw Faceplate & Trim InstallationRear View Faceplate Assembly Diagram Rear View Trim Assembly DiagramStandard Flush Door Flush LouversFull Screen Front To remove the fl ush door, reverse the above stepsSide of the bottom of the fi rebox using Install Spring Hinges to the Left and RightOrder to make the following wire connec Rebox and connect them to the switchAttach door bracket to sides using 4 screws Accent KIT InstallationOptional Screen Doors Double Screen Door attach to left and right side of unitOptional Remote Control Optional Wall Wiring DiagramThermostat Operating Instructions Normal Operating Sounds GAS Appliances Copy of Lighting Instruction PlateMaintenance Straighten adjustment wire FAN MaintenanceFan Access Plate Screws Door GlassRebox and from the valve access plate Valve AssemblyInstall new gasket and valve assembly Replacing fanMain Assembly Parts ListValve Tray Burner & LOG AssemblyBurner Assy NG/LP Burner Grate AssyFull Screen Front Installation FACEPLATES, Trims and Hearths E33 FPI Direct Vent Gas Insert E33 FPI Direct Vent Gas Insert E33 FPI Direct Vent Gas Insert E33 FPI Direct Vent Gas Insert Conditions WarrantyE33 FPI Direct Vent Gas Insert Installer Please complete the following information