Regency E33-NG Optional Screen Doors, Accent KIT Installation, Slide the doors onto the hinges

Page 16

INSTALLATION

Left Side

Faceplate Bracket

Trim Flange

5)Place the bottom hooks of the Surround into the bottom slots of the Faceplate. Slightly pull up the Surround and push the top hooks into the top slots of the Faceplate. Push down to secure. Tug on the Surround to ensure it is securely locked in place.

OPTIONAL SCREEN

DOORS

1)Attach door bracket to sides using 4 screws.

Door Bracket attaches with 2 screws on each side.

2)Take the hoseclamps and put them over the back of each rivet. Squeeze the hoseclamp to secure onto rivets ensuring that the hoseclamp is touching the back side of the surround. The hoseclamp can now be released.

3)Remove the handles by removing the nut and screw. Install the new handles by plac- ing them in position over the holes on the surround louver. Put the screws through the holes and secure them by tightening them with a nut.

Backside of

Surround Shown

Hooks

Faceplate Slots

Double Screen Door: attach to left and right side of unit.

2) Slide the door(s) onto the hinges.

4)Place the emblem over the emblem design on the surround. Insert the studs through the holes. To secure them fi rst put on the split lock washer and then the nut and tighten.

5)Removethe2studsonthesidesoftheHood. Insert the new studs through the holes and secure them by fi rst putting on the washer and then tighten with a nut.

Faceplate

Surround

ACCENT KIT

INSTALLATION

1)Remove the rivets from the surround by pulling off the hoseclamp (located at the backside of surround) with a screwdriver or plyer. Re-install the rivets by putting them through the holes on the sides of the sur- round.

DOUBLE DOOR OPTION

Remove the handles by removing the nut and screw. Install the new handles by plac- ing them in position over the holes on the door(s). Put the studs through the holes and secure them by tightening them with a nut.

16

E33 FPI Direct Vent Gas Insert

Page 15 Page 17
Image 16
Page 15 Page 17
Contents E33 Gas Insert 08/16/05FPI GAS Fireplace Insert E33 FPI Direct Vent Gas InsertTable of Contents Safety Label Installation Installation Checklist Minimum Fireplace OpeningMaterials Required Minimum Fireplace Opening Excalibur OptionMinimum Clearances to Combustibles GAS Connection Flue Liner InstallationVenting Pressure Testing DiagramGAS Pipe Optional Brick PanelLOG Installation Final Installation03-23 03-22 03-18 03-24 03-20 03-19 03-17Locating Pins Locating Pins 03-2003-23 03-20 Locating Pins 03-24 03-23 Locating Pins 03-21E33 Conversion KIT from NG to LPG Conversion Kit Contains QtyShut off the gas supply Remove the louvers and fl ush door Burner Orifice RemovalFaceplate & Trim Installation Pilot Adjustment ScrewRear View Faceplate Assembly Diagram Rear View Trim Assembly DiagramFlush Louvers Standard Flush DoorFull Screen Front To remove the fl ush door, reverse the above stepsInstall Spring Hinges to the Left and Right Side of the bottom of the fi rebox usingOrder to make the following wire connec Rebox and connect them to the switchAccent KIT Installation Attach door bracket to sides using 4 screwsOptional Screen Doors Double Screen Door attach to left and right side of unitOptional Remote Control Optional Wall Wiring DiagramThermostat Operating Instructions Copy of Lighting Instruction Plate Normal Operating Sounds GAS AppliancesMaintenance FAN Maintenance Straighten adjustment wireFan Access Plate Screws Door GlassValve Assembly Rebox and from the valve access plateInstall new gasket and valve assembly Replacing fanParts List Main AssemblyBurner & LOG Assembly Valve TrayBurner Assy NG/LP Burner Grate AssyFull Screen Front Installation FACEPLATES, Trims and Hearths E33 FPI Direct Vent Gas Insert E33 FPI Direct Vent Gas Insert E33 FPI Direct Vent Gas Insert E33 FPI Direct Vent Gas Insert Warranty ConditionsInstaller Please complete the following information E33 FPI Direct Vent Gas Insert
Top Page Image Contents