Regency U39-NG1, U39-LP1 installation manual DV Stove Horizontal Vent KIT Installation

Page 15

INSTALLATION

DV STOVE HORIZONTAL VENT KIT (# 946-116 & #946-216)

DV Stove Horizontal Vent Kit (2 ft. Part # 946-116 or 4 ft. Part # 946-216) includes all the parts needed to install the U39 with minimum horizontal and vertical vent dimensions. For installations that require longer vertical and/or horizontal vents

see the "Dura-vent Termiantion Kit and Component" sections.

Qty. Description

1) 1Rigid Pipe Section (Kit # 946-116: 2 ft. (1.2m) length,

Kit # 946-216: 4 ft. (1.2m) length), 6-1/2" (165mm) inside diameter

2)1Flex Liner, compressed aluminium 2 ply liner,

4" (102mm) inside diameter

3) 4spring spacers

4) 190 deg. Elbow

5) 1Adjustable pipe section 13-1/2" to 24" (343mm x 610mm), 2 pieces

6)1Thimble Cover

7)

1Wall Thimble (2 pcs.)

8)

1Adapter

9)

1AstroCap Termination Cap

10)

2Trim Collar

11)1tube of Mill-Pac, high temperature sealant

12) 12Screws, #8 x 1/2" Self tapping, Stainless Steel

13) 13Screws, #8 x 1/2" Self tapping, Black

14)4Screws #8 x 1-1/2" Drill Point, Black

15)4Screws #8 x 1-1/2" Drill Point, Stainless Steel

16) 8Wood screws #8 x 1"

Optional:

946-206 Vinyl Siding Standoff for AstroCap

Note:

a)Liner sections should be continuous without any joints or seams.

b)This is an approved system, therefore components in this system must not be substituted for any other manufacturer's

products.

DV STOVE HORIZONTAL VENT KIT INSTALLATION

Review the following sequence of instructions which are typical of most installations. The sequence may vary dependingonwallthickness.Referto vent location and clearance dimensions in "Exterior Vent Termination Locations" to "DV Stove Horizontal Vent Kit" sections.

1)Set the unit in its desired location. Check to determine if wall studs will be in the way of the venting system, adjust location until all clearances are met and there are no obstructions.

Note: A 1-1/2"(38mm) clearance around the outer pipe must be maintained except that only a 1" (25mm) clearance is needed at the termination end.

IMPORTANT:

Do not locate termination hood where excessive snow or ice buildup may occur. Be sure to check vent termination area after snow falls,

Minimum Installation Height: U39: 59-3/4" ( 1518mm)

and clear to prevent accidental blockage of venting system. When using snow blowers, make sure snow is not directed towards vent termination area.

2)Assemble a trial fit to determine the vertical center-line for the vent termination.

a)Cut a 9-1/2" x 9-1/2" (241mm x 241 mm) square hole on both the interior and exterior wall.

b)Install wall thimbles on both interior and exterior wall with 4 wood screws (#8 x 1") per thimble.

c)Attach the 2 piece adjustable pipe section to the vent terminal and slide into position from the exterior.

The larger diameter end of the adjustable pipe goes to the vent terminal.

d)Install the 90o elbow onto the adjustable pipe to determine the vertical centerline of the starter collar on the unit.

Regency® U39 ULTIMATE Direct Vent Freestanding Gas Stove

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Ultimate U39 Regency Table of Contents Copy of Safety Label for U39 Gas Stove Safety LabelMA Code CO Detector RequirementsBefore YOU Start InstallationSpecifications Important Message Save These InstructionsInstallation Checklist General Safety InformationClearances to Combustibles Locating Your Ultimate GAS Stove Louver InstallationVenting Introduction Manufactured Mobile Home Additional RequirementsExterior Vent Terminal Description 6-5/8 Rigid Pipe Cross Reference Chart6-5/8 Rigid Pipe Cross Reference Chart Rigid Pipe Venting Systems AlternateMination Caps Vent Restrictor Position Installation Precautions Rigid Pipe Venting ArrangementsSafety Precautions for Installer Horizontal Terminations for All Venting SystemsVertical Venting with Two 2 90o Elbows Horizontal Venting with Two 2 90o ElbowsDV Stove Horizontal Vent KIT Installation Capcanbemounted on DURA-VENT Venting Components Planning Your Dura-Vent InstallationMinimum components for a Dura-Vent Horizontal Installation DURA-VENT Termination KITSnorkel Terminations DURA-VENT Horizontal TerminationsDURA-VENT Vertical Terminations Below Grade InstallationCathedral Ceilings Offset ChartConverting a Factory Built Metal Chimney Approved for US Installations OnlySupport Extensions Round Rdse or Square Sqse GeneralConverting a Masonry Chimney System Data GAS ConnectionHigh Elevation System Data U39 with 40,000 BTULPG Conversion Kit Contains Qty Conversion KIT# 731-969 from NG to LPOnly Required for the U38 Green ground wire Propane Conversion Kit 730-922 Contains GAS Pipe Pressure TestingConversion to Lower BTU Rating Natural Gas Conversion Kit 730-920 ContainsU39 with 30,000 Btu/h Aeration AdjustmentValve Description U39 with 38,000 Btu/hLOG SET Installation B02-56 E02-45 G02 A02-65 Wiring Diagram 14 GA 16 GA 18 GA 20 GA 22 GA Final CheckShutdown Instructions Lighting ProcedureOperating Instructions Operating InstructionsNormal Operating Sounds GAS Appliances Automatic Convection FAN OperationCopy Of Lighting Plate Instructions GOLD-PLATED Doors MaintenanceMaintenance Instructions General Vent MaintenanceDoor Gasket LOG ReplacementLatch Adjustment Glass ReplacementTo Remove U39 Fan FAN MaintenanceDC Sparker Battery Replacement Alternate Fan AccessRemoving Valve Parts List Main AssemblyDescription Burner & LOG Assembly Door Assemblies Conditions WarrantyInstaller Please complete the following information

U39-LP1, U39-NG1 specifications

The Regency U39-LP1 and U39-NG1 are innovative heating appliances designed for modern homes, emphasizing both efficiency and style. These units encapsulate the essence of contemporary design while ensuring high-performance heating solutions. The U39 series stands out for its user-friendly features and advanced technologies that cater to the demands of varied environments.

One of the main features of the U39-LP1 is its propane-fueled operation, allowing it to generate an impressive amount of heat while remaining energy-efficient. The unit is designed with a remarkable heating capacity, making it ideal for larger spaces or for those chilly evenings where comfort is paramount. In contrast, the U39-NG1 operates on natural gas, appealing to homeowners looking for a more sustainable option. Both models allow for quick and effective heating, ensuring a cozy atmosphere within moments.

The technology embedded in both models reflects a commitment to top-tier performance. The advanced electronic ignition system provides reliability, ensuring seamless operation. The units also incorporate a built-in thermostat, which allows for precise control over the temperature, enhancing comfort while conserving energy. Furthermore, the U39 series features a sleek ceramic glass front that not only adds an aesthetic element but also enhances efficiency by radiating heat effectively into the room.

Another hallmark of the Regency U39 series is its design versatility. Both models are available in various finishes, enabling them to blend seamlessly into different décor styles, whether traditional, modern, or minimalist. The compact dimensions of these units ensure they fit effortlessly into a variety of spaces, from living rooms to basements.

Safety is also a significant focus with the U39-LP1 and U39-NG1. The units come equipped with a variety of safety features, including automatic shut-off and heat-resistant materials, ensuring peace of mind for users.

In summary, the Regency U39-LP1 and U39-NG1 models exemplify modern heating solutions characterized by efficiency, advanced technology, and stylish design. With their user-centric features and commitment to safety, these units are perfect additions for anyone seeking warmth and comfort in their homes. Whether powered by propane or natural gas, the U39 series continues to redefine the standard for home heating.
Top Page Image Contents