Regency P40-LP1, P40-NG1 installation manual Door Glass FAN Replacement, Glass Replacement

Page 45

MAINTENANCE

DOOR GLASS

 

FAN REPLACEMENT

Your Regency® fireplace is supplied with high

1)

Unplug the power source.

temperature 5mm-Ceramic glass. If your glass

 

 

requires cleaning, we recommend using an

2)

Remove the power module by lifting it up

approved glass cleaner available at all authorized

 

off of the velcro and pull out.

dealers. Do not use abrasive materials.

 

 

 

6)Remove the fan ground wires.

CAUTION & WARNINGS:

*Do not clean when the glass is hot.

*The use of substitute glass will void all product warranties.

*Care must be taken to avoid breakage of the glass.

*Do not strike or abuse the glass.

*Do not operate this fireplace without the glass front or with a cracked or broken glass front.

*Wear gloves when removing damaged or broken glass.

*Replacement of the glass panel(s) should be done by a licensed or qualified service per son.

GLASS REPLACEMENT

In the event that you break your glass by impact, purchase your replacement from an authorized Regency® dealer only.

Replacement glass is shipped already installed into the door frame. Reinstall as per Glass Door Installation in "Standard Flush Door" section.

CAUTION: Wear gloves when removing damaged or broken glass.

WARNING: Do not operate the appliance with the glass panels removed, cracked or broken. Replacement of the glass panels should be done by a licensed or qualified service person.

Power Module

3)Undo the wire holder by releasing tab.

4)Remove the Control module by lifting it up and off to the side.

7)Disconnect the brown and blue wires connected to the J1 harness.

8)Release the 2 wire tabs.

9)Remove both fans by lifting up off of the pins and tilt sideways and then slide to the left of the firebox and pull out carefully.

10)Reverse steps to re-install.

MAINTENANCE

Control Module

5)Unplug the J1, J2 and J3 harness at the ECS module and pull out the Control module.

NOTE: To facilitate easier re-installation of the fans, apply some lubricante to the rubber grom- mets at the base of the fan bracket.

J1

J2

J3

Regency® P40-1 Direct Vent Gas Fireplace

45

Page 44 Page 46
Image 45
Page 44 Page 46
Contents P40 Gas Fireplace Information for MOBILE/MANUFACTURED Homes After First Sale Manufactured Mobile Home RequirementsTable of Contents Copy of Safety Label InstallationFor the State of Massachusetts only MA Code CO DetectorDimensions Installation Checklist General Safety InformationImportant Message Before YOU StartHeatwave Duct KIT Locating Your GAS FireplaceHeat Release KIT Hearth RequirementsClearances Mantel LEG Clearances Mantel ClearancesP40 Fireplace P40Framing & Finishing Full Screen Door Facing RequirementsHeight = 42-1/2 plus height of hearth Unit Assembly Prior to Installation Venting IntroductionVent Restrictor Position Exterior Vent Termination Requirements Horizontal Termination Flex Venting ArrangementsRigid Pipe Venting Systems Basic Horizontal & Vertical TerminationsHorizontal Termination 58DVA-16AB 8 Rigid Pipe Cross Reference Chart58DVA-RD Offset Pipe SelectionHorizontal Feet Vertical Height Feet Allowable Horizontal TerminationsOption + V1 H + H1 Option + H1Option + H1 V + OptionVent must be supported at offsets Allowable Vertical TerminationsArrow on the vent cap should be pointing up Unit Installation with Horizontal TerminationThis allows for small adjustments Unit Installation With Vertical TerminationDiagram Minimum VentAstrocap XL Dimensions Unit InstallationPilot Adjustment GAS Line InstallationHigh Elevation P40-NG1 System DataBACK-UP Battery Installation GAS Pipe Pressure TestingUnplug the power source Power ModuleLP Conversion Kit Contains Qty Description Conversion KIT #502-969 from NG to LPControl Module Modulating CoilJ9 Jumper NG Conversion Kit Contains Qty Description Conversion KIT #502-966 from LP to NGJ9 Jumper Location Back Brick Panel Brick Panels Completely Installed Brick Panel InstallationEnsure that the logs are not in the unit Top Brick PanelLOG SET Installation 03-3203-40 03-34 03-33 03-341st Log Stand Post 03-33 03-46 03-36 03-46 03-3303-37 03-36 03-3703-38 03-46 03-3603-36 03-32 03-37 03-34 03-40 03-46 03-47 03-382Installing the Manual Control Box Aeration AdjustmentStandard Flush Door Flush LouversWiring Diagram Finishing TrimDo not cut the ground terminal off under any circumstances Full Screen Doors Full Screen Door Frame InstallationUpper Air Register InstallationShutdown Procedure Lighting ProcedureMatching Remote Handset & Control BOX ID Code Operating InstructionsOperation During Power Outage First FireDo not Burn the Appliance Without the Glass Front in Place Normal Operating Sounds GAS Appliances Summary ControlsFor Your Safety Read Before Lighting STOP! Read the safety information above on this labelCopy of Lighting Plate Instructions General Vent Maintenance Maintenance InstructionsLOG Replacement Thermopile ThermocoupleGlass Replacement Door Glass FAN ReplacementWire Valve ReplacementLog Stand Solenoid Valve Compression FittingsPower Module Replacement DC Sparker ReplacementWa & Wb Wires Ring TabsControl Module Replacement Backup Battery ReplacementHeat Shield Main Assembly Parts ListValve Tray Assembly Parts ListFlush Door & Louvers Regency P40-1 Direct Vent Gas Fireplace Regency P40-1 Direct Vent Gas Fireplace Regency P40-1 Direct Vent Gas Fireplace Warranty Installer Please complete the following information

P40-LP1, P40-NG1 specifications

The Regency P40-LP1 and P40-NG1 are notable advancements in the realm of modern technology, particularly designed for energy efficiency and enhanced performance in various applications. These two models cater to the diverse needs of industries striving for both sustainability and productivity.

The P40-LP1 is engineered with a focus on low-pressure applications, utilizing cutting-edge technology to ensure optimal performance in energy consumption. This model features an advanced energy management system that intelligently adjusts power usage based on demand, which not only reduces operational costs but also minimizes the environmental impact. Its compact design and lightweight materials allow for easy installation in various settings, making it a versatile option for multiple industries.

On the other hand, the P40-NG1 is tailored for natural gas applications, making it an ideal choice for environments where natural gas is the primary energy source. This model is equipped with high-efficiency burners that maximize combustion efficiency, producing fewer emissions compared to traditional systems. The P40-NG1 also incorporates an integrated control system, providing users with real-time data monitoring to optimize performance and facilitate preventative maintenance.

Both models are constructed with durable materials designed to withstand harsh operating conditions, ensuring longevity and reliability. Advanced insulation technology further enhances their efficiency by reducing heat loss, allowing these systems to maintain consistent performance over extended periods.

A standout feature of the P40 series is its commitment to user-friendliness. The intuitive interface allows operators to easily navigate settings and access critical system information with minimal training. Additionally, these units are compatible with smart technologies, enabling seamless integration into existing infrastructure for enhanced operational oversight.

In summary, the Regency P40-LP1 and P40-NG1 embody the future of energy solutions, combining efficiency, adaptability, and user-focused design. Whether it’s for low-pressure or natural gas applications, these products deliver reliable performance while adhering to environmental standards. With ongoing advancements in their technology, the P40 series stands as a testament to Regency’s dedication to innovation and sustainability in the energy sector.
Top Page Image Contents