Regency P40-LP1, P40-NG1 installation manual Installation, Upper Air Register

Page 39

INSTALLATION

Simply push in the Full Screen Door Frame until it aligns against the finished wall. Secure Top Flange of Full Screen Door Frame as described in step 4b.

For the Bottom Flange of the Full Screen Door Frame, push the bottom of the Frame until it aligns with the wall. Use the inner cutouts to secure the base of the Frame using the 2x #8 Hex Head Drill Point Screws provided.

8)Slide the Upper Air Register into the louver brackets located on the inside top of the firebox. Push in place.

INSTALLATION

Bottom Flange

Cut Outs

Rear view of Full

Screen Door Frame Shown

Upper Air Register

5)Re-install Glass Door. Refer to the manual for instructions (Page 32).

6)Place the Lower Air Register near hinges. Flip the two hinges over onto the Lower Air Register and

secure with 2x #8 Self Tapping Phillips Screws per

9) Install the Left and Right Side Screen Doors in the

side.

fully open position by placing over top of the hinges

on the Full Screen Door Frame.

 

Hinge Location

NOTE: Failure to install the doors in the fully open

position could result in paint damage to the surface

 

of the door.

Lower Air

Register

7)Secure the Manual Control Panel to the Lower Air

Register with two #8 Self Tapping Phillips screws

(provided) at the right hinge bracket.

Manual Control

Panel

Hinge

 

Hinge

 

Bracket

 

Screen

Right Side

Door

 

of Lower Air

 

Register

10) Close screen doors.

Regency® P40-1 Direct Vent Gas Fireplace

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents P40 Gas Fireplace Information for MOBILE/MANUFACTURED Homes After First Sale Manufactured Mobile Home RequirementsTable of Contents Copy of Safety Label InstallationFor the State of Massachusetts only MA Code CO DetectorDimensions Before YOU Start General Safety InformationInstallation Checklist Important MessageHearth Requirements Locating Your GAS FireplaceHeatwave Duct KIT Heat Release KITClearances P40 Mantel ClearancesMantel LEG Clearances P40 FireplaceFraming & Finishing Full Screen Door Facing RequirementsHeight = 42-1/2 plus height of hearth Unit Assembly Prior to Installation Venting IntroductionVent Restrictor Position Exterior Vent Termination Requirements Horizontal Termination Flex Venting ArrangementsRigid Pipe Venting Systems Basic Horizontal & Vertical TerminationsHorizontal Termination 58DVA-16AB 8 Rigid Pipe Cross Reference Chart58DVA-RD Offset Pipe SelectionHorizontal Feet Vertical Height Feet Allowable Horizontal TerminationsOption + V1 H + H1 Option + H1Option + H1 V + OptionVent must be supported at offsets Allowable Vertical TerminationsArrow on the vent cap should be pointing up Unit Installation with Horizontal TerminationMinimum Vent Unit Installation With Vertical TerminationThis allows for small adjustments DiagramAstrocap XL Dimensions Unit InstallationP40-NG1 System Data GAS Line InstallationPilot Adjustment High ElevationPower Module GAS Pipe Pressure TestingBACK-UP Battery Installation Unplug the power sourceLP Conversion Kit Contains Qty Description Conversion KIT #502-969 from NG to LPControl Module Modulating CoilJ9 Jumper NG Conversion Kit Contains Qty Description Conversion KIT #502-966 from LP to NGJ9 Jumper Location Top Brick Panel Brick Panel InstallationBack Brick Panel Brick Panels Completely Installed Ensure that the logs are not in the unitLOG SET Installation 03-3203-40 03-34 03-33 03-341st Log Stand Post 03-36 03-37 03-46 03-3303-33 03-46 03-36 03-3703-34 03-40 03-46 03-47 03-382 03-46 03-3603-38 03-36 03-32 03-37Flush Louvers Aeration AdjustmentInstalling the Manual Control Box Standard Flush DoorWiring Diagram Finishing TrimDo not cut the ground terminal off under any circumstances Full Screen Doors Full Screen Door Frame InstallationUpper Air Register InstallationOperating Instructions Lighting ProcedureShutdown Procedure Matching Remote Handset & Control BOX ID CodeOperation During Power Outage First FireDo not Burn the Appliance Without the Glass Front in Place Normal Operating Sounds GAS Appliances Summary ControlsFor Your Safety Read Before Lighting STOP! Read the safety information above on this labelCopy of Lighting Plate Instructions Thermopile Thermocouple Maintenance InstructionsGeneral Vent Maintenance LOG ReplacementGlass Replacement Door Glass FAN ReplacementSolenoid Valve Compression Fittings Valve ReplacementWire Log StandRing Tabs DC Sparker ReplacementPower Module Replacement Wa & Wb WiresControl Module Replacement Backup Battery ReplacementHeat Shield Main Assembly Parts ListValve Tray Assembly Parts ListFlush Door & Louvers Regency P40-1 Direct Vent Gas Fireplace Regency P40-1 Direct Vent Gas Fireplace Regency P40-1 Direct Vent Gas Fireplace Warranty Installer Please complete the following information

P40-LP1, P40-NG1 specifications

The Regency P40-LP1 and P40-NG1 are notable advancements in the realm of modern technology, particularly designed for energy efficiency and enhanced performance in various applications. These two models cater to the diverse needs of industries striving for both sustainability and productivity.

The P40-LP1 is engineered with a focus on low-pressure applications, utilizing cutting-edge technology to ensure optimal performance in energy consumption. This model features an advanced energy management system that intelligently adjusts power usage based on demand, which not only reduces operational costs but also minimizes the environmental impact. Its compact design and lightweight materials allow for easy installation in various settings, making it a versatile option for multiple industries.

On the other hand, the P40-NG1 is tailored for natural gas applications, making it an ideal choice for environments where natural gas is the primary energy source. This model is equipped with high-efficiency burners that maximize combustion efficiency, producing fewer emissions compared to traditional systems. The P40-NG1 also incorporates an integrated control system, providing users with real-time data monitoring to optimize performance and facilitate preventative maintenance.

Both models are constructed with durable materials designed to withstand harsh operating conditions, ensuring longevity and reliability. Advanced insulation technology further enhances their efficiency by reducing heat loss, allowing these systems to maintain consistent performance over extended periods.

A standout feature of the P40 series is its commitment to user-friendliness. The intuitive interface allows operators to easily navigate settings and access critical system information with minimal training. Additionally, these units are compatible with smart technologies, enabling seamless integration into existing infrastructure for enhanced operational oversight.

In summary, the Regency P40-LP1 and P40-NG1 embody the future of energy solutions, combining efficiency, adaptability, and user-focused design. Whether it’s for low-pressure or natural gas applications, these products deliver reliable performance while adhering to environmental standards. With ongoing advancements in their technology, the P40 series stands as a testament to Regency’s dedication to innovation and sustainability in the energy sector.
Top Page Image Contents