Regency P40-NG1, P40-LP1 installation manual LOG SET Installation, 03-32, 03-40

Page 32

INSTALLATION

LOG SET INSTALLATION

INSTALLATION

Read the instructions below carefully and refer to the pictures. If the logs are broken do not use the unit until they are replaced. Broken logs can interfere with the pilot operation.

Log kit (Part # 503-930) contains the following pieces:

a)

03-32

Back Log

b)

03-40

Ember Bed

c)

03-34

Front Left Log

d)

03-33

Middle Back Log

e)

03-36

Middle Right Cross Log

f)

03-37

Front Right Log

g)

03-38

Small Ember

h)

03-46

Log Center Left Y

i)

03-47

Log Center Y

j)

902-154

Embers Lava

k)

902-179

Vermiculite

l)

902-153

Rockwool

m)946-669 Platinum Embers (supplied with packaged manual)

03-47

03-37

03-46

03-33

03-38 (1)

03-34

03-40

3)Fit log 03-32 into the pins on the back air box. Push the log tight against the back brick panel.

4)Re-install the brackets removed in step 2 to hold the log in place.

03-32

5)Position log 03-40 up to and against the 2 tabs located on the front burner. Then slide log 03-40 to the right until it touches the burner tube.

03-32

03-38 (2)

Front Burner

03-36

1)Carefully remove the logs from the box and unwrap them. The logs are fragile, handle with care - do not force into position.

2)Remove the brackets on the left and right side of the back air box.

03-40

Burner Tube

Back Air

Box

32

Regency® P40-1 Direct Vent Gas Fireplace

Page 31 Page 33
Image 32
Page 31 Page 33
Contents P40 Gas Fireplace Manufactured Mobile Home Requirements Information for MOBILE/MANUFACTURED Homes After First SaleTable of Contents Installation Copy of Safety LabelMA Code CO Detector For the State of Massachusetts onlyDimensions General Safety Information Installation ChecklistImportant Message Before YOU StartLocating Your GAS Fireplace Heatwave Duct KITHeat Release KIT Hearth RequirementsClearances Mantel Clearances Mantel LEG ClearancesP40 Fireplace P40Height = 42-1/2 plus height of hearth Framing & FinishingFull Screen Door Facing Requirements Vent Restrictor Position Unit Assembly Prior to InstallationVenting Introduction Exterior Vent Termination Requirements Venting Arrangements Horizontal Termination FlexHorizontal Termination Rigid Pipe Venting SystemsBasic Horizontal & Vertical Terminations 8 Rigid Pipe Cross Reference Chart 58DVA-16ABOffset Pipe Selection 58DVA-RDAllowable Horizontal Terminations Horizontal Feet Vertical Height FeetOption + H1 Option + V1 H + H1Option Option + H1 V +Allowable Vertical Terminations Vent must be supported at offsetsUnit Installation with Horizontal Termination Arrow on the vent cap should be pointing upUnit Installation With Vertical Termination This allows for small adjustmentsDiagram Minimum VentUnit Installation Astrocap XL DimensionsGAS Line Installation Pilot AdjustmentHigh Elevation P40-NG1 System DataGAS Pipe Pressure Testing BACK-UP Battery InstallationUnplug the power source Power ModuleConversion KIT #502-969 from NG to LP LP Conversion Kit Contains Qty DescriptionJ9 Jumper Control ModuleModulating Coil Conversion KIT #502-966 from LP to NG NG Conversion Kit Contains Qty DescriptionJ9 Jumper Location Brick Panel Installation Back Brick Panel Brick Panels Completely InstalledEnsure that the logs are not in the unit Top Brick Panel03-40 LOG SET Installation03-32 1st Log Stand Post 03-3403-33 03-34 03-46 03-33 03-33 03-46 03-3603-37 03-36 03-3703-46 03-36 03-3803-36 03-32 03-37 03-34 03-40 03-46 03-47 03-382Aeration Adjustment Installing the Manual Control BoxStandard Flush Door Flush LouversDo not cut the ground terminal off under any circumstances Wiring DiagramFinishing Trim Full Screen Door Frame Installation Full Screen DoorsInstallation Upper Air RegisterLighting Procedure Shutdown ProcedureMatching Remote Handset & Control BOX ID Code Operating InstructionsDo not Burn the Appliance Without the Glass Front in Place Operation During Power OutageFirst Fire Summary Controls Normal Operating Sounds GAS AppliancesCopy of Lighting Plate Instructions For Your Safety Read Before LightingSTOP! Read the safety information above on this label Maintenance Instructions General Vent MaintenanceLOG Replacement Thermopile ThermocoupleDoor Glass FAN Replacement Glass ReplacementValve Replacement WireLog Stand Solenoid Valve Compression FittingsDC Sparker Replacement Power Module ReplacementWa & Wb Wires Ring TabsHeat Shield Control Module ReplacementBackup Battery Replacement Parts List Main AssemblyParts List Valve Tray AssemblyFlush Door & Louvers Regency P40-1 Direct Vent Gas Fireplace Regency P40-1 Direct Vent Gas Fireplace Regency P40-1 Direct Vent Gas Fireplace Warranty Installer Please complete the following information

P40-LP1, P40-NG1 specifications

The Regency P40-LP1 and P40-NG1 are notable advancements in the realm of modern technology, particularly designed for energy efficiency and enhanced performance in various applications. These two models cater to the diverse needs of industries striving for both sustainability and productivity.

The P40-LP1 is engineered with a focus on low-pressure applications, utilizing cutting-edge technology to ensure optimal performance in energy consumption. This model features an advanced energy management system that intelligently adjusts power usage based on demand, which not only reduces operational costs but also minimizes the environmental impact. Its compact design and lightweight materials allow for easy installation in various settings, making it a versatile option for multiple industries.

On the other hand, the P40-NG1 is tailored for natural gas applications, making it an ideal choice for environments where natural gas is the primary energy source. This model is equipped with high-efficiency burners that maximize combustion efficiency, producing fewer emissions compared to traditional systems. The P40-NG1 also incorporates an integrated control system, providing users with real-time data monitoring to optimize performance and facilitate preventative maintenance.

Both models are constructed with durable materials designed to withstand harsh operating conditions, ensuring longevity and reliability. Advanced insulation technology further enhances their efficiency by reducing heat loss, allowing these systems to maintain consistent performance over extended periods.

A standout feature of the P40 series is its commitment to user-friendliness. The intuitive interface allows operators to easily navigate settings and access critical system information with minimal training. Additionally, these units are compatible with smart technologies, enabling seamless integration into existing infrastructure for enhanced operational oversight.

In summary, the Regency P40-LP1 and P40-NG1 embody the future of energy solutions, combining efficiency, adaptability, and user-focused design. Whether it’s for low-pressure or natural gas applications, these products deliver reliable performance while adhering to environmental standards. With ongoing advancements in their technology, the P40 series stands as a testament to Regency’s dedication to innovation and sustainability in the energy sector.
Top Page Image Contents