Infinity NV30C owner manual Problem Solving, Spécifications Techniques

APPRENEZ À CONNAÎTRE VOTRE BALAYEUSE CYCLONIC

TROUBLESHOOTING

VERTICALE

Changing the Headlight WARNING: To reduce the risk of electric shock, the power cord must be disconnected before performing maintenance/trouble shooting checks. Occasionally the headlight will require changing.

1.Turn the vacuum off and unplug from the electrical outlet.

2.With a flathead screw driver, insert the end of the screwdriver into the two slots on top of the headlight lens and gently pull down. (Fig. 59)

Lens Slots

Fig. 59

3.Lift out the headlight lens.

4.Remove the light bulb by pulling it out carefully.

5.Replace the new bulb by pushing it in.

6.To replace the headlight lens, insert the bottom tabs of the lens into the holding slots and snap the top back into place to secure.

PROBLEM SOLVING

This appliance was inspected thoroughly and was in good operating condition when it was shipped from the factory. If a minor problem occurs, it usually can be solved quite easily when the cause is found. Therefore, this checklist is provided for your convenience.

1.Poignée

2.Tube Télescopique

3.Poignée de Transport

4.Bouton de Dégagement de la Porte Inférieure du Collecteur Cyclone.

5.Collecteur Cyclone

6.Bac à Poussière

7.Écran de Débris

8.Lumière d’Indicateur du Filtre

9.Lumière

10.Bouton d’Ajustement de la Hauteur du Tapis

11.Protège-Meuble

12.Déclencheur de Poignée

13.Sélecteur Tapis-à-Plancher

14.Support du Tube Inférieur

15.Tuyau Super Extensible

16.Suceur Plat

17.Brosse à Meubles

18.Brosse à Épousseter

19.Bouton de Dégagement du Bac à Poussière

20.Port de Rinçage du Collecteur Cyclone

21.Support du Tube Supérieur

22.Support de Dégagement Rapide du Cordon d’Alimentation

23.Dégagement du Tube Télescopique

24.Support du Cordon d’Alimentation

25.Bouton Marche/Arrêt

PROBLEM		POSSIBLE CAUSE	POSSIBLE SOLUTION
	1.	Not properly plugged into wall	1.	Plug in firmly.
Cleaner Won’t		outlet.	2.	Reset circuit breaker or
	2.	No electricity in wall outlet.		replace fuse.
Run
	3.	On/Off switch not turned on.	3.	Push on/off switch to on
	4.	Motor thermostat tripped.	4.	Reset motor thermostat.
	1.	Full or clogged dust cup.	1.	Clean dust cup.
	2.	Wrong carpet height setting.
			2.	Adjust setting.
	3.	Clogged air path.
			3.	Remove obstruction.
	4.	Clogged hose.
Cleaner Won't			4.	Remove obstruction.
	5.	Broken belt(s).
			5.	Replace belt(s).
Pick Up	6. Telescopic wand not inserted
			6.	Push telescopic wand in
		fully.
				securely.
	7.	Dirty filters.
			7.	Clean / change filters
	8.	Debris screen needs
			8.	Clean debris screen.
		cleaning.
Cleaner Picks
Up Moveable	1.	Wrong carpet height setting.	1.	Adjust setting.
Rugs Or Pushes
Too Hard
Agitator Does	1.	Broken belt(s).	1.	Replace belt(s).
Not Turn	2.	Belt(s) installed incorrectly.	2.	Check belt changing.

Spécifications Techniques

Voltage :	120V, 60Hz.
Alimentation :	12 A

Remarque : * Les illustrations peuvent différer du produit exact.

Air Flow	1.	Attachment use restricts air
Restricted With		flow.	1.	Check attachment.
Attachment Use	2.	New carpet debris clogging	2.	Remove obstruction.
Sound Changes		air path.

33 14