Integra DTR-7.3 instruction manual Ir Out

Page 25

Operating components not reached by the remote controller signals (IR IN/OUT)

In order to use the remote controller to control the DTR-7.3 from a remote location, you will need to prepare a multi-room kit (sold separately) such as one of those given below:

•Onkyo’s Multi-Room System kits (IR Remote Controller Extension System)

•Multiroom A/V distribution and control system such as those from Niles® and Xantech®

If the remote controller signal does not reach the DTR-7.3 remote sensor

If the DTR-7.3 is located inside a cabinet or other enclosure where the infrared rays from the remote controller cannot enter, then operation with the remote controller will not be possible. In such a case, it will be necessary to install a remote sensor at a location outside of the cabinet for the infrared rays from the controller can reach.

With this connection, select “Main” for the Hardware Setup → IR IN Setup → Position setting in the Setup Menu (see page 42).

Connectiong

IR Receiver

block

IR IN

DTR-7.3

Remote controller

In the cabinet

: Signal flow

The IR IN input allows you to control the DTR-7.3 from the remote zone (Zone 2) with the remote controller even though the remote zone may be on the other side of the building from the main zone. The diagram below shows how to make the proper connections for the remote zone.

With this connection, select “Zone 2” for the Hardware Setup → IR IN Setup → Position setting in the Setup Menu (see page 42).

To IR IN

IR Receiver DTR-7.3

Connecting block

Remote controller

Main room

Zone 2 room

: Signal flow

Make the connection as shown below. Do not plug in any equipment to the power outlet until all the connections are complete.

from connecting block

Mini plug cable

I R

IN

OUT

DTR-7.3

If the remote controller signal does not reach other components

In this situation, you will need to use a commercially available IR emitter. Connect the mini plug of the IR emitter to the IR OUT terminal on the DTR-7.3 and then place the IR emitter on the remote sensor of the component or facing it. When the IR emitter is connected, only the signal input to the IR IN terminal is output to the IR OUT terminal. The signal input from the remote sensor on the front of the DTR-7.3 will not be output to the IR OUT terminal.

 

Connectiong

IR Receiver

IR IN

block

 

 

 

IR OUT

DTR-7.3

 

IR Emitter

 

 

 

 

Remote controller

Other

 

 

component

 

 

 

: Signal flow

 

Other component

: Signal flow

Remote control

 

 

 

 

sensor

I R

 

Emitter

IN

 

 

Mini plug

Mini plug cable

OUT

 

DTR-7.3

IR Emitter

 

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents DTR-7.3 Avis Important SafeguardsPrecautions Contents Contents Supplied accessories FeaturesInstalling the remote controller batteries Before using this unitUsing the remote controller Front panel Index parts and facilitiesIndex parts and facilities Front panel display Remote controller Mode buttons and indicators 28 Send/Learn indicatorOn/Standby button Sleep buttonRear panel Connecting to Audio/Video equipment Connecting your audio components Connecting to Audio/Video equipmentConnecting a compact disc player CD Connecting a turntable PhonoConnecting a DVD Player Connecting your video componentsFlow of the video signals is as follows Connecting a DVD player DVDConnecting a video cassette recorder Video Connecting a television monitor or projector Monitor OUTSignal flow Video Connecting video camera, etc. Video 5 InputIdeal speaker configuration Connecting speakersMinimum speaker configuration for surround sound playback Speaker placementConnecting speakers Connecting speakersUsing the speaker labels Connecting the AM antenna cable Connecting antennasConnecting the included antennas Assembling the AM loop antennaConnecting antennas When using the Surr BACK/ZONE 2 Speakers terminals Connecting the remote zone Zone 2 speakersWhen using the Zone 2 OUT terminals When using the Surr BACK/ZONE 2 PRE OUT terminalsIR OUT Connecting the power cords from other devices Connections for remote controlMiscellaneous Connections RS 232 portConnecting to devices with analog multi channel output Connecting to an external device with 12V Trigger terminalConnecting auxiliary power amplifier Miscellaneous ConnectionsTurning on the power Connecting the powerTurning on the power from the remote controller Basic operation Enjoying music or videos with the DTR-7.3To change the display of the input source from Tape to MD Listening with headphones Adjusting the bass and trebleUsing the sleep time remote controller only Enjoying music or videos with the DTR-7.3Setup Enter Return Changing the listening modeWhile playing back DTS sources While playing back Analog/PCM sourcesAdjusting the brightness of the front display Switching the displayTemporarily changing the speaker output levels Enjoying the multichannel output Changing the audio modeListening to a stereo radio station FM mode Tuning into a radio stationListening to Radio Broadcasts Selecting a preset radio station Presetting a radio stationErasing a preset radio station Listening to Radio BroadcastsAdjusting the volume for the remote zone Using the buttons on the DTR-7.3Enjoying music in the remote zone Rec Out Recording a sourceStart recording at the recording component as desired Press the Rec Out button Recording a sourceBasic Menu Setup MenuAdvanced Menu Navigating through the Setup Menu Setup MenuPress the Setup button Hardware Setup Menu Hardware SetupSurr Back/Zone 2 Sub-menu Speaker Impedance Sub-menuIR in Setup Sub-menu Hardware SetupSpeaker Setup Menu Speaker SetupSpeaker Config Sub-menu Speaker Distance Sub-menu Speaker SetupPress the Test button to complete the procedure Using the remote controller Press the Test buttonLevel Calibration Sub-menu Calibrating the speaker levelsInput Setup Menu Input SetupInitial settings for each input source Digital InputDigital Format Input SetupInput source selected Multichannel Last Valid enables the source last selected Select to have Video Setup Sub-menuVideo Component VideoIntelliVolume IntelliVolume Sub-menuCharacter Input Sub-menu Character DisplayRelationship between input source and listening mode Listening Mode Preset Sub-menuListening Mode Type of softwareListening Modes Input source signalsTrigger Setup Sub-menu Audio Adjust Setup Menu Audio AdjustSetting Values Initial value Tone Control Sub-menuDelay Sub-menu Audio AdjustSound Effect Sub-menu LFE Level Sub-menu Theater Dimensional Sub-menuMono Sub-menu Surround Sub-menu THX Sub-menu Listening mode Treble Setting Tone ControlSound Effect Bass Re-EQPreference Volume Setup Sub-menuPreference Menu OSD Setup Sub-menu Headphones Level Setup Sub-menuPreference OSD Position Sub-menuRcvr Mode Using remote controllerOverview Controlling an Integra/Onkyo cassette tape deckControlling an Integra/Onkyo DVD player Using remote controllerPress the CD Mode button On Standby CD Mode DiscControlling an Integra/Onkyo CD player Press the SAT/MD Mode button On Standby SAT/MD ModeControlling an Integra/Onkyo MD recorder Rec RecordLearning a pre-programming code Entering a pre-programming codeVOL DisplayEntering a pre-programming code Setting NoPre-programming codes DVD Mode DVD Player Mode Operating your programmed remote controllerSAT Mode Satellite Tuner Mode Cable Mode Cable ModeVCR Mode VCR Mode Operating your programmed remote controllerTV Mode TV Mode Light Macro 1 Macro Programming procedureErasing all the commands programmed under a Mode button Erasing the programmed command from one buttonPress and release the same Mode button again Press and release the same button againWhat is the macro function? Using the macro functionProgramming the macro Executing the macroErasing all commands and macros that have been programmed Using the macro functionErasing a macro from the Macro 1 or 2 button Troubleshooting guide Video and Audio Troubleshooting guideIf one of the messages shown below appears Specifications Net-Tune Features Internet radio featuresModem To the WAN side To the LAN side port Connecting the DTR-7.3 to your Ethernet NetworkEnjoying Internet radio Enjoying Music on Internet Radio or NAS-2.3Playing a music file saved in NAS-2.3 Enjoying Music on Internet Radio or NAS-2.3To cancel the operation Using the Alphanumeric keysUse the / buttons to select one of the menu Caps Press the Enter buttonNetwork Setup Menu Configuring Various SettingsProxy Setup Sub-menu Configuring Various SettingsIP Address Sub-menu MAC Address Sub-menuSpecifications Troubleshooting guideAppendix

DTR-7.3 specifications

The Integra DTR-7.3 is a state-of-the-art AV receiver designed for audiophiles and home theater enthusiasts who seek a blend of performance, flexibility, and advanced technology. With a powerful amplifier section, the DTR-7.3 delivers an exceptional audio experience, providing crystal-clear sound reproduction across all frequencies.

At the heart of the DTR-7.3 is the ability to deliver 9.2 channels of amplification, making it an ideal choice for a comprehensive home theater setup. It supports various speaker configurations, allowing users to create immersive surround sound environments. The receiver is equipped with sophisticated DSP (Digital Signal Processing) that enhances audio fidelity while supporting multiple audio formats, including Dolby Atmos, DTS:X, and IMAX Enhanced. These technologies enable sound to move in a three-dimensional space, wrapping listeners in a dynamic auditory experience.

One of the standout features of the DTR-7.3 is its 4K Ultra HD video capabilities, ensuring that users can enjoy high-quality imagery with up to 60 frames per second. The receiver is equipped with HDR (High Dynamic Range) support, allowing for deeper contrast and more vibrant colors. Additionally, it includes multiple HDMI inputs and outputs, making it easy to connect to various devices, including gaming consoles, Blu-ray players, and streaming devices.

Connectivity is also a strong suit of the DTR-7.3. It supports Wi-Fi, Bluetooth, and Ethernet, granting users the ability to stream music from a variety of online services without the hassle of physical connections. The receiver is compatible with various music streaming protocols such as AirPlay, Spotify Connect, and TIDAL, allowing for seamless access to a vast library of audio content.

The DTR-7.3 also includes an advanced room calibration system that optimizes sound according to the specific acoustics of the room. This feature automates the tuning process, ensuring that every listening position benefits from balanced sound.

In addition, the user-friendly interface and the Integra Remote App make it easy to operate, allowing users to control their home theater setup from their smartphones or tablets. With its impressive combination of features, advanced technologies, and easy connectivity, the Integra DTR-7.3 stands out as a top-tier choice for anyone looking to elevate their home entertainment experience.
Top Page Image Contents