Integra DTR-7.3 instruction manual THX Sub-menu

Page 57

Audio Adjust

3-9. THX Sub-menu

This sub-menu allows you to set the settings that will be enabled when the THX listening mode is selected. The settings available are shown in the table below.

Setting

Values

Initial value

a. Re-EQ (THX)

Off, On

On

 

 

 

b. Decoder (2ch)

PL II Movie

PL II Movie

 

Neo:6 Cinema

 

 

 

 

c. THX Surr EX

Auto, Off, On

On

(Dolby D)

 

 

 

 

 

d. DTS-ES

Auto, Off, On

Auto

 

 

 

a. Re-EQ (THX)

Re-EQ (re-equalization) takes the edginess or “brightness” out of your home cinema sound to compensate for the fact that sound mixed for theaters may sound too bright when played back through speakers in the home environment.

This can be set to either “On” or “Off”.

b. Decoder (Analog/PCM)

This setting allows you to select the decoding mode for THX processing.

PL II Movie: Select for Dolby Pro Logic II Movie.

Neo:6 Cinema: Select for DTS Neo:6 Cinema.

c. THX Surr EX (Dolby D)

This setting allows you to set whether or not Dolby Digital sources will be played back using THX Surround EX when a surround back speaker is connected.

Auto: Select to automatically output sources with EX- identifying signals using THX Surround EX.

On: Select to output using THX Surround EX regardless of whether or not the source contains EX identifiers.

Off: Select not to output using THX Surround EX regardless of whether or not the source contains EX identifiers (Dolby D is used).

Note:

THX Surround EX (Dolby D) will not appear if the Surr Back/Zone 2 setting in the Surr Back/Zone 2 Sub-menu of the Hardware Setup Menu is set to “Zone 2.”

d. DTS-ES

This setting allows you to select the DTS-ES mode for THX processing.

Auto: Select to have the listening mode change automatically to DTS-ES Discrete 6.1 or DTS-ES Matrix 6.1. If the DTS source has no DTS-ES flag, the mode is changed to DTS 5.1 when the DTS source has the DTS-ES flag (ID signal for DTS-ES).

On: Select to have the listening mode change automatically to DTS-ES Discrete 6.1 or DTS-ES Matrix 6.1 when the DTS source has the DTS-ES flag, and to DTS-ES Matrix 6.1 when the DTS source has no DTS-ES flag.

Off: Select to not use DTS-ES listening modes even when the DTS source has the DTS-ES flag. With this setting, the DTS sources are always played in DTS 5.1 mode.

3-10. 3-11. 3-12. 3-13. 3-14. 3-15.

Mono Movie/Enhanced 7/Orchestra/Unplugged/ Studio Mix /TV Logic Sub-menu

The settings of these sub-menus become effective when any of the Mono Movie, Enhanced 7, Orchestra, Unplugged, Studio-Mix, or TV Logic listening modes are selected. When one of the listening modes is selected, the settings in the sub-menu of that listening mode become enabled.

Setting

Values

Initial value

a. Front Effect

Off, On

On

 

 

 

b. Reverb Level

Low, Mid, High

Mid

 

 

 

c. Reverb Time

Short, Mid, Long

Mid

 

 

 

a. Front Effect

Some live recordings contain acoustic reverberation. When you play these sources, more reverberation will be applied by the DSP, creating too much reverb effects and the sound loses frame or presence. In this case, set this setting to “Off” so that no reverberation from the DSP will be applied to the sound output from the three front channels. With this setting, the sound source is played as it is without any further reverberation.

b. Reverb Level

This setting allows you to adjust the depth of acoustic reverberation to match the playback source material, the acoustics of your room, and such other factors.

Select from the three settings “Low,” “Mid,” and “High.”

c. Reverb Time

Adjust the reverb time to match the source being played back and the acoustics of the room. Select from the three settings “Short,” “Mid,” and “Long.”

57

Page 56 Page 58
Image 57
Page 56 Page 58
Contents DTR-7.3 Avis Important SafeguardsPrecautions Contents Contents Supplied accessories FeaturesBefore using this unit Installing the remote controller batteriesUsing the remote controller Front panel Index parts and facilitiesIndex parts and facilities Front panel display Remote controller Mode buttons and indicators 28 Send/Learn indicatorOn/Standby button Sleep buttonRear panel Connecting to Audio/Video equipment Connecting your audio components Connecting to Audio/Video equipmentConnecting a compact disc player CD Connecting a turntable PhonoConnecting a DVD Player Connecting your video componentsFlow of the video signals is as follows Connecting a DVD player DVDConnecting a video cassette recorder Video Connecting a television monitor or projector Monitor OUTSignal flow Video Connecting video camera, etc. Video 5 InputIdeal speaker configuration Connecting speakersMinimum speaker configuration for surround sound playback Speaker placementConnecting speakers Connecting speakersUsing the speaker labels Connecting the AM antenna cable Connecting antennasConnecting the included antennas Assembling the AM loop antennaConnecting antennas When using the Surr BACK/ZONE 2 Speakers terminals Connecting the remote zone Zone 2 speakersWhen using the Zone 2 OUT terminals When using the Surr BACK/ZONE 2 PRE OUT terminalsIR OUT Connecting the power cords from other devices Connections for remote controlMiscellaneous Connections RS 232 portConnecting to devices with analog multi channel output Connecting to an external device with 12V Trigger terminalConnecting auxiliary power amplifier Miscellaneous ConnectionsConnecting the power Turning on the powerTurning on the power from the remote controller Enjoying music or videos with the DTR-7.3 Basic operationTo change the display of the input source from Tape to MD Listening with headphones Adjusting the bass and trebleUsing the sleep time remote controller only Enjoying music or videos with the DTR-7.3Setup Enter Return Changing the listening modeWhile playing back DTS sources While playing back Analog/PCM sourcesSwitching the display Adjusting the brightness of the front displayTemporarily changing the speaker output levels Enjoying the multichannel output Changing the audio modeTuning into a radio station Listening to a stereo radio station FM modeListening to Radio Broadcasts Selecting a preset radio station Presetting a radio stationErasing a preset radio station Listening to Radio BroadcastsUsing the buttons on the DTR-7.3 Adjusting the volume for the remote zoneEnjoying music in the remote zone Recording a source Rec OutStart recording at the recording component as desired Press the Rec Out button Recording a sourceSetup Menu Basic MenuAdvanced Menu Setup Menu Navigating through the Setup MenuPress the Setup button Hardware Setup Menu Hardware SetupSurr Back/Zone 2 Sub-menu Speaker Impedance Sub-menuIR in Setup Sub-menu Hardware SetupSpeaker Setup Speaker Setup MenuSpeaker Config Sub-menu Speaker Distance Sub-menu Speaker SetupPress the Test button to complete the procedure Using the remote controller Press the Test buttonLevel Calibration Sub-menu Calibrating the speaker levelsInput Setup Menu Input SetupInitial settings for each input source Digital InputInput Setup Digital FormatInput source selected Multichannel Last Valid enables the source last selected Select to have Video Setup Sub-menuVideo Component VideoIntelliVolume IntelliVolume Sub-menuCharacter Input Sub-menu Character DisplayRelationship between input source and listening mode Listening Mode Preset Sub-menuListening Mode Type of softwareListening Modes Input source signalsTrigger Setup Sub-menu Audio Adjust Setup Menu Audio AdjustSetting Values Initial value Tone Control Sub-menuAudio Adjust Delay Sub-menuSound Effect Sub-menu Theater Dimensional Sub-menu LFE Level Sub-menuMono Sub-menu Surround Sub-menu THX Sub-menu Listening mode Treble Setting Tone ControlSound Effect Bass Re-EQVolume Setup Sub-menu PreferencePreference Menu OSD Setup Sub-menu Headphones Level Setup Sub-menuPreference OSD Position Sub-menuRcvr Mode Using remote controllerOverview Controlling an Integra/Onkyo cassette tape deckControlling an Integra/Onkyo DVD player Using remote controllerOn Standby CD Mode Disc Press the CD Mode buttonControlling an Integra/Onkyo CD player Press the SAT/MD Mode button On Standby SAT/MD ModeControlling an Integra/Onkyo MD recorder Rec RecordLearning a pre-programming code Entering a pre-programming codeVOL DisplaySetting No Entering a pre-programming codePre-programming codes DVD Mode DVD Player Mode Operating your programmed remote controllerSAT Mode Satellite Tuner Mode Cable Mode Cable ModeOperating your programmed remote controller VCR Mode VCR ModeTV Mode TV Mode Light Macro 1 Macro Programming procedureErasing all the commands programmed under a Mode button Erasing the programmed command from one buttonPress and release the same Mode button again Press and release the same button againWhat is the macro function? Using the macro functionProgramming the macro Executing the macroUsing the macro function Erasing all commands and macros that have been programmedErasing a macro from the Macro 1 or 2 button Troubleshooting guide Video and Audio Troubleshooting guideIf one of the messages shown below appears Specifications Net-Tune Features Internet radio featuresModem To the WAN side To the LAN side port Connecting the DTR-7.3 to your Ethernet NetworkEnjoying Internet radio Enjoying Music on Internet Radio or NAS-2.3Playing a music file saved in NAS-2.3 Enjoying Music on Internet Radio or NAS-2.3To cancel the operation Using the Alphanumeric keysUse the / buttons to select one of the menu Caps Press the Enter buttonNetwork Setup Menu Configuring Various SettingsProxy Setup Sub-menu Configuring Various SettingsIP Address Sub-menu MAC Address Sub-menuTroubleshooting guide SpecificationsAppendix

DTR-7.3 specifications

The Integra DTR-7.3 is a state-of-the-art AV receiver designed for audiophiles and home theater enthusiasts who seek a blend of performance, flexibility, and advanced technology. With a powerful amplifier section, the DTR-7.3 delivers an exceptional audio experience, providing crystal-clear sound reproduction across all frequencies.

At the heart of the DTR-7.3 is the ability to deliver 9.2 channels of amplification, making it an ideal choice for a comprehensive home theater setup. It supports various speaker configurations, allowing users to create immersive surround sound environments. The receiver is equipped with sophisticated DSP (Digital Signal Processing) that enhances audio fidelity while supporting multiple audio formats, including Dolby Atmos, DTS:X, and IMAX Enhanced. These technologies enable sound to move in a three-dimensional space, wrapping listeners in a dynamic auditory experience.

One of the standout features of the DTR-7.3 is its 4K Ultra HD video capabilities, ensuring that users can enjoy high-quality imagery with up to 60 frames per second. The receiver is equipped with HDR (High Dynamic Range) support, allowing for deeper contrast and more vibrant colors. Additionally, it includes multiple HDMI inputs and outputs, making it easy to connect to various devices, including gaming consoles, Blu-ray players, and streaming devices.

Connectivity is also a strong suit of the DTR-7.3. It supports Wi-Fi, Bluetooth, and Ethernet, granting users the ability to stream music from a variety of online services without the hassle of physical connections. The receiver is compatible with various music streaming protocols such as AirPlay, Spotify Connect, and TIDAL, allowing for seamless access to a vast library of audio content.

The DTR-7.3 also includes an advanced room calibration system that optimizes sound according to the specific acoustics of the room. This feature automates the tuning process, ensuring that every listening position benefits from balanced sound.

In addition, the user-friendly interface and the Integra Remote App make it easy to operate, allowing users to control their home theater setup from their smartphones or tablets. With its impressive combination of features, advanced technologies, and easy connectivity, the Integra DTR-7.3 stands out as a top-tier choice for anyone looking to elevate their home entertainment experience.
Top Page Image Contents