FireplaceXtrordinair 36 DV EFIII owner manual Horizontal Terminations using 6-5/8 Diameter Vent

Page 21

Installation (for qualified installers only)

2 1

Horizontal Terminations using 6-5/8” Diameter Vent

Use a single 90° elbow (NOTE: an additional 45° elbow may be used on the horizontal run).

The termination must fall within the shaded area shown in the chart. Use the indicated restrictor position.

10' (max)

5 feet

0 feet

NOTE:

0feet

5feet

10feet

12'(max)

Use Restrictor

Position #1

3 foot length (max)

Warning:

When an elbow is used directly off the top of the fireplace, a 2" clearance is required above the vent (1" below and to the sides).

0feet

5feet

10feet

12'(max)

10' (max)

5feet

0feet

• Horizontal sections require a 1/4" rise every 12" of travel.

• Restrictor positions are based upon lab tests. The ideal restrictor position may vary slightly.

Travis Industries

4040708

1 0 0 - 0 1 1 6 0

Image 21

Contents If YOU Smell GAS 2Introduction Introduction Important InformationTravis Industries 4040708 0 0 1 1 6 Table of Contents If YOU Smell GAS Safety PrecautionsThis Manual 6Features and Specifications Features Installation OptionsNatural Gas Propane Installation Warnings Installation OverviewPacking List Additional Items Required Fireplace Placement Requirements Minimum Framing DimensionsClearances Raised Fireplaces Corner InstallationsFloor Mounted Fireplaces Hearth RequirementsFacing Over 1 Thick Facing RequirementsTOP View Facing DetailInstallation for Face DimensionsModifying the Face Angle for Rectangular Faces Side View Facing and Hearth ExamplesDV Fireplace Mantel Requirements Combustible MantelsNon-Combustible Mantels Altitude Considerations Vent RequirementsUse of 8 Diameter Pipe Part Numbers for 6-5/8 Diameter VentHorizontal Vent Requirements Vent InstallationRestrictor Position Approved Vent ConfigurationsElbows Measuring Vent LengthsZero or Two 45 Offsets 0feet 5feet 10feet 12max 10 max Feet Horizontal Terminations using 6-5/8 Diameter VentFeet 5feet 10feet 15feet 20feet 25max 40 max Horizontal Terminations using 8 Diameter Vent Termination Requirements see the illustration below Fuel Gas Line RequirementsGas Line Connection Gas Inlet PressureElectrical Connection Re-Attaching the Glass Frame Finalizing the InstallationGlass Frame Removal Spring Pin Installation 8Finalizing the InstallationTop 0Finalizing the Installation StepFront View Side View Correct Fine Tuning the EMBER-FYRE Burner 2Finalizing the InstallationOperation3 Before You BeginLocation of Controls See explanation below Starting The Pilot Flame 4OperationAdjusting the Flame Height Starting the Fireplace for the First TimeTurning the Fireplace On and Off Optional Power Heat Duct Adjusting the Blower Speed6Operation Normal Operating SoundsMaintenance3 Yearly Service ProcedureMaintaining Your Fireplaces Appearance Troubleshooting MaintenanceHow this Fireplace Works What Turns the Main Burners On and OffWhat Prevents Gas Buildup 0Maintenance Wiring DiagramReplacement Parts List Minimum Clearances to Combustibles Safety LabelYears 1 & 2 Coverage Parts & Labor 2Limited 7 Year WarrantyLP Conversion Instructions Burner ReplacementOptional Equipment for qualified installers only Slotted Screwdriver Or T-20 Torx Power Heat Duct Wall or Ceiling Mounting Optional Equipment for qualified installers only Wiring Diagram Follow the directions below to wire the blower box Maintenance Instructions 2Index

36 DV EFIII specifications

The FireplaceXtrordinair 36 DV EFIII is a remarkable direct vent gas fireplace that blends innovative technology with aesthetic appeal, making it an ideal addition to any modern living space. Renowned for its exceptional design and performance, this fireplace provides both warmth and ambience while ensuring efficiency and safety.

One of the standout features of the 36 DV EFIII is its impressive heating capacity. It boasts a maximum output of up to 28,000 BTUs, providing sufficient heat to effectively warm large areas while maintaining energy efficiency. This model is equipped with a powerful fan system that circulates warm air throughout the room, enhancing comfort levels even in colder months.

The FireplaceXtrordinair 36 DV EFIII incorporates advanced technology, including a state-of-the-art electronic ignition system. This feature allows for quick and easy startups without the hassle of traditional matches or lighters. Additionally, the unit is designed with a modulating gas valve, which adjusts the flame height to optimize both heat output and fuel consumption, resulting in impressive energy savings.

The fireplace is also designed with versatility in mind. It offers customizable options, including various decorative media, such as traditional logs, rocks, or contemporary glass, allowing homeowners to create the desired aesthetic that complements their interior design. The 36 DV EFIII is available with multiple front styles and finishes, ensuring it integrates seamlessly with any décor.

Safety is paramount with the FireplaceXtrordinair 36 DV EFIII, featuring a sealed combustion system that draws air from outside the home, reducing the risk of indoor pollution. The direct vent design ensures that all exhaust is expelled outside, providing a clean and safe burning experience.

Another notable characteristic of the 36 DV EFIII is its easy maintenance. The unit is designed for straightforward cleaning, with an accessible glass front that can be easily removed for periodic maintenance. This convenience makes it an attractive option for homeowners looking for a user-friendly fireplace solution.

In conclusion, the FireplaceXtrordinair 36 DV EFIII is a premium direct vent gas fireplace that combines elegance, efficiency, and safety. With its impressive heating capabilities, customizable features, and advanced technology, it stands out as an excellent choice for anyone looking to enhance their home with a high-quality fireplace.