Heat & Glo LifeStyle CERONA-42, CERONA-36 owner manual Lighting Appliance, Intellifire Ignition

Page 44

B. Lighting Appliance

Intellifire Ignition

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing prop- erty damage, personal injury or loss of life.

LIGHTING

INSTRUCTIONS

1.

Turn off all electric power to the appli-

 

ance.

2.

This appliance is equipped with an elec-

A. This appliance is equipped with an electronic pilot ignition de- vice which automatically lights the pilot. Do not try to light the pilot by hand.

B. BEFORE LIGHTING, smell all

around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

•Do not touch any electric switch; do not use any phone in your build- ing.

•Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

•If you cannot reach your gas sup- plier, call the fire department.

C. Do not use this appliance if any part has been under water. Imme- diately call a qualified service tech- nician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

 

tronic pilot ignition device which auto-

 

matically lights the pilot. Do not try to light

 

the pilot by hand.

3.

Wait five (5) minutes to clear out any

 

gas. Then smell for gas, including near

 

the floor. If you smell gas, STOP! Fol-

 

low "B" in the Safety Information located

 

on the left side of this label. If you don't

 

smell gas, go to next step.

4.

Turn on all electric power to the appliance.

5.

Push the Flame ON button.

Note: There will be a 3 minute

WARNING:

DO NOT CONNECT 110 VAC TO THE CONTROL VALVE.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property dam- age. Refer to the owner's informa- tion manual provided with this ap- pliance.

This appliance needs fresh air for safe operation and must be in- stalled so there are provisions for adequate combustion and ventila- tion air.

If not installed, operated, and main- tained in accordance with the manufacturer's instructions, this product could expose you to sub- stances in fuel or fuel combustion which are known to the State of Cali- fornia to cause cancer, birth de- fects, or other reproductive harm.

Keep burner and control compart- ment clean. See installation and operating instructions accompany- ing appliance.

CAUTION:

Hot while in operation. Do not touch. Keep children, clothing, fur- niture, gasoline and other liquids having flammable vapors away.

Do not operate the appliance with panel(s) removed, cracked or bro- ken. Replacement of the panel(s) should be done by a licensed or qualified service person.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and pro- pane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the al- ternate fuel.

Also Certified for Installation in a Bedroom or a Bedsitting Room.

For assistance or additional infor- mation, consult a qualified installer, service agency or the gas supplier.

delay before the burner will light.

6.If the appliance will not operate, follow the instructions “To Turn Off Gas to Ap- pliance” and call your service technician or gas supplier.

Note: To operate pilot without the burner, push the pilot button.

TO TURN OFF GAS TOAPPLIANCE

1.Turn off all electric power to the appli- ance if service is to be performed.

2.Flip both Pilot and Flame ON/OFF switches to the “OFF” position.

ForadditionalinformationonoperatingyourHearthTechnologiesappliance,pleaserefertowww.Fireplaces.com.

2095-913B

44

Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06

Page 43 Page 45
Image 44
Page 43 Page 45
Contents CERONA-36 CERONA-42 Congratulations Homeowner Reference InformationTable of Contents High Altitude Installations BTU SpecificationsNon-Combustible Materials Specification Combustible Materials SpecificationRequirements for the Commonwealth of Massachusetts Design and Installation Considerations Getting StartedInspect Appliance and Components Tools and Supplies NeededFraming and Clearances Selecting Appliance LocationConstructing the Appliance Chase ClearancesMantel Projections TOP of Arch OpeningHearth Extension Cerona-42Termination Locations Vent Termination Minimum ClearancesService Alcove ApplicationsContinue Adding Vent Components Install Support BracketsTo Install the Heat Shield Vent Information and Diagrams Vent Table KeyUse of Elbows Measuring StandardsVent Diagrams Top Vent Horizontal TerminationCerona-36 only 0.5 ft Cerona-36 onlyV1 = 50 FT MAX .2 M Top Vent Horizontal Termination Three ElbowsTop Vent Vertical Termination 152 Vent Clearances and Framing Pipe Clearances to CombustiblesWall Penetration Framing Combustible Wall PenetrationVertical Penetration Framing Installing the Ceiling FirestopInstalling Attic Shield Removing Non-combustible Facing Material Assembly Appliance PreparationMaterial Installing Non-combustible FacingSecuring and Leveling the Appliance Installing Flue Restrictors Cerona-36 Cerona-42Installing Vent Pipe Assembly of Vent SectionsAttaching Vent to the Firebox Assembly Assembling Pipe SectionsAssembling Minimum Installations MI Sections Assembling DVP-12A Slip SectionsHorizontal Sections Disassembly of Vent SectionsSecuring the Vent Sections Vertical Sections Heat Shield Requirements for Horizontal Termination Installing Heat Shield and Horizontal Termination CapInstalling the Horizontal Termination Cap Installing Roof Flashing and Vertical Termination Cap 14 Minimum Height from Roof to Lowest Discharge OpeningAssembling and Installing Storm Collar 17 Assembling the Storm Collar Around the PipeGas Information Fuel Conversions Gas ConnectionGas Pressures Pressure Natural Gas PropaneHigh Altitude Installations Electrical Information Recommendation for WireOptional Accessories Requirements Not operate unless Properly groundedJunction Box Installation 11Finishing Facing MaterialFinishing Material Options Risk of FireFinishing Material Thickness from 3/4 in. to 1-1/4 Finishing Material Thickness greater than 1-1/4 inchPosition of board and template Appliance Setup Clean the ApplianceAccessories Ember PlacementLog Assembly LOGS-Cerona36 Positioning the Logs Model Cerona-36LOG #4 SRV2106-704 Log #4 is form Model Cerona-42 Step Grilles and Trim Glass AssemblyAir Shutter Setting Before operating this appliance have a qualified technician Operating InstructionsBefore Lighting Appliance Lighting Appliance Intellifire IgnitionAfter Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure Troubleshooting Intellifire Ignition SystemTroubleshooting Intellifire Ignition System Maintaining and Servicing Appliance Before servicingInspect Maintenance Tasks Model Cerona-36 Model Cerona-42 Appliance Dimensions Diagram16Reference Materials Vent Components Diagrams DVP45 45 ElbowDVP-TRAPK1 DVP-TRAP2 DVP-TRAPK2 COOL-ADD DVP-FBHT Service Parts Cerona-36 Log Set AssemblyService Parts List CERONA-36Cerona-42 Log Set Assembly CERONA-42CERONA-42 CERONA-36 CERONA-42 Limited Lifetime Warranty Limited Lifetime Warranty Heat & GLO GAS Appliance ProductsContact Information
Related manuals
Manual 64 pages 10.74 Kb Manual 1 pages 2.44 Kb

CERONA-42, CERONA-36 specifications

The Heat & Glo LifeStyle CERONA-36 and CERONA-42 are elegant gas fireplaces designed to enhance the ambiance of any living space while providing effective heating solutions. These models stand out due to their sleek design and innovative technologies that cater to modern homeowners seeking both comfort and style.

One of the primary features of the CERONA series is their clean, contemporary aesthetic. The linear design maximizes the display of flames and minimizes visual distractions, making them a focal point in any room. With options for various finishes and customizable media, including glass and logs, homeowners can truly personalize their fireplace to match their décor.

The CERONA-36 and CERONA-42 are equipped with advanced burner technology that ensures an exceptional flame presentation. The high-efficiency burners not only produce beautiful flames but also optimize heat output while maintaining energy efficiency. These fireplaces are designed to provide warmth without sacrificing environmental consciousness, making them an ideal choice for eco-aware consumers.

Both models come with Heat & Glo's patented IntelliFire Technology, which allows for adaptive ignition and reliable operation. This technology ensures that the fireplace ignites quickly and safely, providing peace of mind for users. Additionally, the remote control feature allows for easy operation from anywhere in the room, enhancing convenience when it comes to controlling the temperature and ambiance.

The CERONA series also incorporates a unique Power Vent technology. This enables the fireplace to vent up to 40 feet horizontally and vertically, offering flexibility in installation and allowing for greater design possibilities for any space in the home.

Moreover, the fireplaces are designed with sound-dampening features that reduce operational noise, ensuring a peaceful ambiance while maximizing the visual experience of dancing flames.

The straightforward maintenance and cleaning requirements of the CERONA-36 and CERONA-42 further contribute to their appeal. With a user-friendly design, these fireplaces simplify upkeep, making them suitable for busy lifestyles.

In summary, the Heat & Glo LifeStyle CERONA-36 and CERONA-42 gas fireplaces are remarkable heating solutions that combine aesthetics, technology, and user convenience. Their modern design, efficient operation, and adaptable installation options make them a valuable addition to any contemporary home, ensuring both warmth and elegance for years to come.
Top Page Image Contents