DMP Electronics XR2500F manual LX-Bus, Outputs, Relays, Zone Reference, Compliance Instructions

Page 10

Introduction

1.7LX-Bus™

You can connect the following devices to the LX-Bus™ provided by the DMP 481 (supplied) or by the 462N, 481, 462P, 463G, and 472 Interface Cards up to the maximum number of LX-Bus™ addresses. See Accessory Devices.

•Model 521LX or 521LXT Smoke Detectors with CleanMe

•Sixteen-, eight-, four- and/or single-zone expansion modules

•Single-zone detectors

•Relay output expansion modules

•Graphic annunciator modules

1.8Outputs

The XR2500F provides two pre-installed Model 305 Single Pole, Double Throw (SPDT) relay outputs, each rated 1 Amp at 30 VDC (power limited sources only).

The XR2500F also provides four programmable open collector outputs rated for 30 VDC @ 50mA each. The open collector outputs provide ground connection for a positive voltage source. A Model 300 Output Harness is required to use these outputs and may be connected to a Model 860 Relay Output Module.

1.9Relays

The XR2500F ships with two Model 305 Relays pre-installed to allow zone alarm control for the 866 NAC Modules. When a fire alarm occurs the bell output is factory programmed to turn on and provide power to the contacts of the relays. Specific zone programming determines whether one or both relays turn on signal voltage to the 866 NACs. This allows control of the NACs by zone.

1.10 Zone Reference

The XR2500F has been pre-wired in the factory. The first 866 NAC module connects to Zone 1. The second 866 NAC module connects to Zone 2.

1.11 Compliance Instructions

For applications that must conform to a local authorities installation standard or a National Recognized Testing Laboratory certificated system, please see the Wiring Diagrams for Notification Appliances and the Listed Compliance Specifications section near the end of this guide for additional instructions.

Digital Monitoring Products

XR2500F Installation Guide

2

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Installation Guide Model XR2500F Command Processor Installation Guide Introduction Secondary Power SupplyFire Command Center MountingPowered Zones for 2-Wire Smoke Detectors Accessory DevicesBattery Information J22 LX-Bus Expansion ConnectorListed Compliance Specifications J1 Ethernet ConnectorReset and Tamper Headers Universal UL Burglary SpecificationsPolice Station Connected and Local Burglar Alarm Units Holdup Alarm UnitsDigital Burglar Alarm Communicator System Units ANSI/ UL Access Control System UnitsWiring Diagrams California State Fire Marshal SpecificationsNew York City MEA Specifications Household Fire Warning System Units ANSI/UL 985, NfpaThis page intentionally left blank Introduction Relays LX-BusOutputs Zone ReferenceMounting Wiring Diagram Use Marking16 VAC Transformer Transformers and AC Power ConnectionAC Connection Earth Ground GNDBattery Connection to XR2500F Command Processor panel Secondary Power SupplyDescription Connection Two 866 NAC ModulesBell Silence/Bell Trouble XR2500F On-board LX-Bus Installing the 481 CardLX-Bus Operation LX-Bus 481 Zone Expansion Interface Card893A Dual Phone Line Module Notification FCC RegistrationFire Command Center Remote Fire Command CenterZone Expansion ExpansionOutput Expansion Accessory Devices Lightning ProtectionAccessory Devices Connecting LX-Bus and Keypad Bus Devices Mounting Keypads and Zone Expansion ModulesBattery Information 11.7 XR2500F Standby Battery Calculations Copy Sub-Totals to nextThis page only Standby Battery Selection Bell Output Keypad BusTerminals 11 Powered Zones for 2-Wire Smoke DetectorsSmoke and Glassbreak Detector Output Current RatingCompatible 2-Wire Smoke Detector Chart DS250HDTerminals Keyswitch Arming ZoneProtection Zones Operational ParametersDry Contact Relay Outputs Output Harness WiringContact Rating J23 6-Pin Header Model 300 Harness WiringJ11 Annunciator Outputs Model 860 Relay ModuleSerial Connector LEDs J22 LX-Bus Expansion ConnectorJ21 Serial Connector LX-Bus Interface Cards23.1 J16 Reset Header J1 Ethernet ConnectorReset and Tamper Headers Ethernet LEDsListed Compliance Specifications Universal UL Burglary SpecificationsHousehold Burglar-Alarm System Units ANSI/UL Area InformationStandard or Encrypted Line Security Proprietary DialerDact Central Station Model 463G Cell Only, Standard or Encrypted Line SecurityPath 1 programming Path 2 programming Path 3 programming Digital Burglar Alarm Communicator System Units ANSI/ UL Holdup Alarm UnitsPolice Station Connected and Local Burglar Alarm Units Bell Automatic Bell TestPath 1 programming Path 2 programming Path 3 programming Panel Designation Access Control System UnitsMercantile Compatible DevicesUniversal Fire Alarm Specifications Local Protective Signaling Systems Power SupplyPower Fail Delay Remote Station Protective Signaling SystemsNotification Appliances Ground FaultHousehold Fire Warning System Units ANSI/UL 985, Nfpa Cross ZoningDigital Dialer and Network Communication California State Fire Marshal SpecificationsNew York City MEA Specifications Communication ProgrammingWiring Diagrams Prewired 866 Modules with NAC ExtenderWiring Diagrams Alarm Bell PWR Bell Out + Bell Trouble DSM-12/24 Module 39.5 867 Class B Style W Notification Appliance Circuit To initiating zoneTo initiating zone DMP Model Dual Style D Zone Module Installation Command Processor Panel Remote Station Reversing Relay ConnectionSecond LX-Bus with Auxiliary Power Supply XR2500F 481 Command Processor PanelLX-Bus Module Connection Powered Burglary Devices Model 860 Relay Module ConnectionRevisions to This Document Ver Section Number and Heading Quick Explanation of ChangesThis page intentionally left blank Operating Instructions Model XR2500F Panels Mounting Instructions Listings and Approvals

XR2500F specifications

The DMP Electronics XR2500F is an advanced and versatile electronic device designed to cater to a wide range of applications including industrial automation, robotics, and smart home technologies. Known for its robust performance and reliable functionalities, the XR2500F stands out as a leading option in the market.

One of the main features of the XR2500F is its powerful processing unit, which ensures efficient handling of complex tasks and data processing. With a clock speed of up to 2.5 GHz, the device is capable of multitasking, enabling users to run multiple applications simultaneously without compromising performance. This makes the XR2500F an ideal choice for applications that require real-time data processing and analysis.

The XR2500F is equipped with an extensive array of connectivity options, including Wi-Fi, Bluetooth, and Ethernet capabilities. This allows for seamless integration with various devices and networks. The wireless options facilitate easy communication with cloud services and other IoT devices, making it suitable for smart home automation systems, where synchronization and control are critical.

In terms of memory, the XR2500F offers significant storage capacity, with options that can accommodate up to 64GB of RAM and 512GB of flash storage. This ample memory ensures that users can store large amounts of data and run memory-intensive applications without experiencing slowdowns. Additionally, the device supports expandable memory options, allowing for future upgrades to meet growing demands.

The XR2500F also incorporates advanced security technologies to protect sensitive data. Features like end-to-end encryption and secure boot processes safeguard against unauthorized access and data breaches. This is particularly important in industrial settings where data integrity is critical for operational safety.

Another remarkable characteristic of the XR2500F is its energy efficiency. Designed with the latest power management technologies, the device minimizes energy consumption while maximizing performance. This not only reduces operational costs but also aligns with green technology initiatives.

Overall, the DMP Electronics XR2500F is a high-performance electronic device that combines powerful processing, extensive connectivity, robust memory, enhanced security, and energy efficiency. Its versatility and reliability make it a preferred choice for professionals seeking innovative solutions in automation and control systems.
Top Page Image Contents