DMP Electronics XR2500F manual Notification, FCC Registration

Page 18

Introduction

7.9Notification

The user must not repair registered terminal equipment. In case of trouble, immediately unplug the device from the telephone jack. The factory warranty provides for repairs. Registered terminal equipment may not be used on party lines or in connection with coin telephones. No­tify the telephone company with the following information:

a. The particular line(s) where the service is connected

b. The FCC registration number c. The ringer equivalence

d. The device make, model, and serial number (see the serial # sticker on the panel)

7.10 FCC Registration

The Model XR2500F complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the outside of the enclosure of this equipment is a label that contains, among other information, a product identifier in the format US:CCKAL00BXR500. If requested this number must be provided to the telephone company.

A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. See installation instructions for details.

The Ringer Equivalence Number (REN) is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company.

If the XR2500F causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.

If trouble is experienced with the Model XR2500F, for repair or warranty information, please contact DMP at the address and telephone number listed on the back of this document. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.

If your premises has specially wired alarm equipment connected to the telephone line, ensure the installation of the XR2500F does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.

Caution: To ensure proper operation, this equipment must be installed according to the installation instructions in this manual. To verify that the equipment is operating properly and can successfully report an alarm, this equipment must be tested immediately after installation, and periodically thereafter, according to the test instructions in this document and the XR500 Series Programming Guide (LT-0679). Additionally, verification of Line Seize capability should be made immediately after installation, and periodically thereafter, in order to ensure that this equipment can initiate a call even when other equipment (telephone, answering system, computer modem, etc.) connected to the same line is in use.

Digital Monitoring Products

XR2500F Installation Guide

10

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Installation Guide Model XR2500F Command Processor Installation Guide Introduction Secondary Power SupplyFire Command Center MountingPowered Zones for 2-Wire Smoke Detectors Accessory DevicesBattery Information J22 LX-Bus Expansion ConnectorListed Compliance Specifications J1 Ethernet ConnectorReset and Tamper Headers Universal UL Burglary SpecificationsPolice Station Connected and Local Burglar Alarm Units Holdup Alarm UnitsDigital Burglar Alarm Communicator System Units ANSI/ UL Access Control System UnitsWiring Diagrams California State Fire Marshal SpecificationsNew York City MEA Specifications Household Fire Warning System Units ANSI/UL 985, NfpaThis page intentionally left blank Introduction Relays LX-BusOutputs Zone ReferenceMounting Wiring Diagram Use Marking16 VAC Transformer Transformers and AC Power ConnectionAC Connection Earth Ground GNDSecondary Power Supply Battery Connection to XR2500F Command Processor panelDescription Two 866 NAC Modules ConnectionBell Silence/Bell Trouble XR2500F On-board LX-Bus Installing the 481 CardLX-Bus Operation LX-Bus 481 Zone Expansion Interface Card893A Dual Phone Line Module Notification FCC RegistrationFire Command Center Remote Fire Command CenterExpansion Zone ExpansionOutput Expansion Accessory Devices Lightning ProtectionAccessory Devices Connecting LX-Bus and Keypad Bus Devices Mounting Keypads and Zone Expansion ModulesBattery Information 11.7 XR2500F Standby Battery Calculations Copy Sub-Totals to nextThis page only Standby Battery Selection Bell Output Keypad BusTerminals 11 Powered Zones for 2-Wire Smoke DetectorsSmoke and Glassbreak Detector Output Current RatingCompatible 2-Wire Smoke Detector Chart DS250HDTerminals Keyswitch Arming ZoneProtection Zones Operational ParametersOutput Harness Wiring Dry Contact Relay OutputsContact Rating J23 6-Pin Header Model 300 Harness WiringJ11 Annunciator Outputs Model 860 Relay ModuleSerial Connector LEDs J22 LX-Bus Expansion ConnectorJ21 Serial Connector LX-Bus Interface Cards23.1 J16 Reset Header J1 Ethernet ConnectorReset and Tamper Headers Ethernet LEDsListed Compliance Specifications Universal UL Burglary SpecificationsHousehold Burglar-Alarm System Units ANSI/UL Area InformationStandard or Encrypted Line Security Proprietary DialerDact Central Station Model 463G Cell Only, Standard or Encrypted Line SecurityPath 1 programming Path 2 programming Path 3 programming Holdup Alarm Units Digital Burglar Alarm Communicator System Units ANSI/ ULPolice Station Connected and Local Burglar Alarm Units Bell Automatic Bell TestPath 1 programming Path 2 programming Path 3 programming Panel Designation Access Control System UnitsMercantile Compatible DevicesUniversal Fire Alarm Specifications Local Protective Signaling Systems Power SupplyPower Fail Delay Remote Station Protective Signaling SystemsNotification Appliances Ground FaultHousehold Fire Warning System Units ANSI/UL 985, Nfpa Cross ZoningDigital Dialer and Network Communication California State Fire Marshal SpecificationsNew York City MEA Specifications Communication ProgrammingWiring Diagrams Prewired 866 Modules with NAC ExtenderWiring Diagrams Alarm Bell PWR Bell Out + Bell Trouble DSM-12/24 Module 39.5 867 Class B Style W Notification Appliance Circuit To initiating zoneTo initiating zone DMP Model Dual Style D Zone Module Installation Command Processor Panel Remote Station Reversing Relay ConnectionSecond LX-Bus with Auxiliary Power Supply XR2500F 481 Command Processor PanelLX-Bus Module Connection Powered Burglary Devices Model 860 Relay Module ConnectionRevisions to This Document Ver Section Number and Heading Quick Explanation of ChangesThis page intentionally left blank Operating Instructions Model XR2500F Panels Mounting Instructions Listings and Approvals

XR2500F specifications

The DMP Electronics XR2500F is an advanced and versatile electronic device designed to cater to a wide range of applications including industrial automation, robotics, and smart home technologies. Known for its robust performance and reliable functionalities, the XR2500F stands out as a leading option in the market.

One of the main features of the XR2500F is its powerful processing unit, which ensures efficient handling of complex tasks and data processing. With a clock speed of up to 2.5 GHz, the device is capable of multitasking, enabling users to run multiple applications simultaneously without compromising performance. This makes the XR2500F an ideal choice for applications that require real-time data processing and analysis.

The XR2500F is equipped with an extensive array of connectivity options, including Wi-Fi, Bluetooth, and Ethernet capabilities. This allows for seamless integration with various devices and networks. The wireless options facilitate easy communication with cloud services and other IoT devices, making it suitable for smart home automation systems, where synchronization and control are critical.

In terms of memory, the XR2500F offers significant storage capacity, with options that can accommodate up to 64GB of RAM and 512GB of flash storage. This ample memory ensures that users can store large amounts of data and run memory-intensive applications without experiencing slowdowns. Additionally, the device supports expandable memory options, allowing for future upgrades to meet growing demands.

The XR2500F also incorporates advanced security technologies to protect sensitive data. Features like end-to-end encryption and secure boot processes safeguard against unauthorized access and data breaches. This is particularly important in industrial settings where data integrity is critical for operational safety.

Another remarkable characteristic of the XR2500F is its energy efficiency. Designed with the latest power management technologies, the device minimizes energy consumption while maximizing performance. This not only reduces operational costs but also aligns with green technology initiatives.

Overall, the DMP Electronics XR2500F is a high-performance electronic device that combines powerful processing, extensive connectivity, robust memory, enhanced security, and energy efficiency. Its versatility and reliability make it a preferred choice for professionals seeking innovative solutions in automation and control systems.
Top Page Image Contents