DMP Electronics XR2500F manual Remote Fire Command Center

Page 19

Introduction

Fire Command Center

8.1Description

The XR2500F provides an LCD display and 20-key keyboard for programming and system user operation. The Fire Command Center is installed on the XR2500F enclosure door. A keyswitch is installed and pre-wired

to the left of the keyboard. The user must turn the keyswitch to enable the four function keys. See the illustration below.

			Fire Command Center
	POWER
	TROUBLE
	ALARM
	SILENCE
	RESET	ABC	DEF	GHI	JKL
	RESET	1	2	3	4
		1	2	3	4
	ENABLE
	TEST	MNO	PQR	STU	VWX
	TEST	5	6	7	8
		5	6	7	8
	DRILL	YX			COMMAND
	DRILL	9	0		COMMAND
		9	0

Figure 10: Fire Command Center LCD and Keyboard

8.2Connection

The display and keyboard are factory pre-wired to the XR2500F panel terminals 7, 8, 9, and 10. For standby battery calculations, the display draws 92mA of current in normal standby or alarm condition. See Panel Standby Battery Calculations. The keyswitch is pre-wired to the membrane keyboard.

8.3Remote Fire Command Center

Up to fifteen Model 630F Remote Fire Command Centers may be remotely attached to the XR2500F system. See the 630F Installation Guide (LT-0741) for additional information.

XR2500F Installation Guide

Digital Monitoring Products

11

Image 19

Contents

Installation Guide Model XR2500F Command Processor Installation Guide Mounting Secondary Power SupplyFire Command Center IntroductionJ22 LX-Bus Expansion Connector Accessory DevicesBattery Information Powered Zones for 2-Wire Smoke DetectorsUniversal UL Burglary Specifications J1 Ethernet ConnectorReset and Tamper Headers Listed Compliance SpecificationsAccess Control System Units Holdup Alarm UnitsDigital Burglar Alarm Communicator System Units ANSI/ UL Police Station Connected and Local Burglar Alarm UnitsHousehold Fire Warning System Units ANSI/UL 985, Nfpa California State Fire Marshal SpecificationsNew York City MEA Specifications Wiring DiagramsThis page intentionally left blank Introduction Zone Reference LX-BusOutputs RelaysMounting Use Marking Wiring DiagramEarth Ground GND Transformers and AC Power ConnectionAC Connection 16 VAC TransformerBattery Connection to XR2500F Command Processor panel Secondary Power SupplyDescription Connection Two 866 NAC Modules Bell Silence/Bell Trouble LX-Bus 481 Zone Expansion Interface Card Installing the 481 CardLX-Bus Operation XR2500F On-board LX-Bus893A Dual Phone Line Module FCC Registration NotificationRemote Fire Command Center Fire Command CenterZone Expansion ExpansionOutput Expansion Lightning Protection Accessory DevicesAccessory Devices Mounting Keypads and Zone Expansion Modules Connecting LX-Bus and Keypad Bus DevicesBattery Information Copy Sub-Totals to next 11.7 XR2500F Standby Battery CalculationsThis page only Standby Battery Selection Keypad Bus Bell OutputCurrent Rating Powered Zones for 2-Wire Smoke DetectorsSmoke and Glassbreak Detector Output Terminals 11DS250HD Compatible 2-Wire Smoke Detector ChartOperational Parameters Keyswitch Arming ZoneProtection Zones TerminalsDry Contact Relay Outputs Output Harness WiringContact Rating Model 860 Relay Module Model 300 Harness WiringJ11 Annunciator Outputs J23 6-Pin HeaderLX-Bus Interface Cards J22 LX-Bus Expansion ConnectorJ21 Serial Connector Serial Connector LEDsEthernet LEDs J1 Ethernet ConnectorReset and Tamper Headers 23.1 J16 Reset HeaderUniversal UL Burglary Specifications Listed Compliance SpecificationsArea Information Household Burglar-Alarm System Units ANSI/ULModel 463G Cell Only, Standard or Encrypted Line Security Proprietary DialerDact Central Station Standard or Encrypted Line SecurityPath 1 programming Path 2 programming Path 3 programming Digital Burglar Alarm Communicator System Units ANSI/ UL Holdup Alarm UnitsPolice Station Connected and Local Burglar Alarm Units Automatic Bell Test BellPath 1 programming Path 2 programming Path 3 programming Compatible Devices Access Control System UnitsMercantile Panel DesignationUniversal Fire Alarm Specifications Remote Station Protective Signaling Systems Power SupplyPower Fail Delay Local Protective Signaling SystemsCross Zoning Ground FaultHousehold Fire Warning System Units ANSI/UL 985, Nfpa Notification AppliancesCommunication Programming California State Fire Marshal SpecificationsNew York City MEA Specifications Digital Dialer and Network CommunicationPrewired 866 Modules with NAC Extender Wiring DiagramsWiring Diagrams Alarm Bell PWR Bell Out + Bell Trouble DSM-12/24 Module To initiating zone 39.5 867 Class B Style W Notification Appliance CircuitTo initiating zone DMP Model Dual Style D Zone Module Installation Remote Station Reversing Relay Connection Command Processor PanelXR2500F 481 Command Processor Panel Second LX-Bus with Auxiliary Power SupplyLX-Bus Module Connection Model 860 Relay Module Connection Powered Burglary DevicesVer Section Number and Heading Quick Explanation of Changes Revisions to This DocumentThis page intentionally left blank Mounting Instructions Listings and Approvals Operating Instructions Model XR2500F Panels