DMP Electronics XR2500F manual Introduction

Page 9

Introduction

Introduction

1.1Overview

The DMP XR2500F Addressable Fire Alarm Control Panel (FACP) is an expandable 24 VDC Fire Alarm Control with built-in DACT and LCD Fire Command Center keyboard with membrane keyswitch. A complete system can provide:

•574 programmable inputs and outputs for commercial and industrial fire alarm service.

•Eight on-board grounded zones

•Two on-board 12 VDC Class B, Stye A powered zones

Connect a 12 or 24 VDC regulated, power limited power supply listed for Fire Protective Signaling Systems to distribute notification appliance power between the two class B style W NAC outputs. Additional NAC outputs can be added with conventional supervision modules or addressable power supply/boosters. Addressable smoke detectors and input modules round out the XR2500F to deliver a truly flexible and expansive fire detection and notification system. The Fire Alarm Control Panel is shipped pre-wired in a red metal enclosure housing the necessary components to monitor and control fire alarm notification appliances.

The enclosure dimensions are as follows: 32” H x 14.5” W x 4” D. The lid adds about 0.5” to each side.

1.2System Components

The XR2500F FACP consists of the following pre-wired components:

• One Model XR2500F Command Processor panel

•

One Model 893A Dual Phone Line module

• Two Model 866 Class B Style W NAC modules

•

One Model 630F PCB and membrane switch

•

One 16 VAC, 56 VA transformer

•

Two Model 305 Plug-in Relays

•

One Model 481 Zone Expansion Interface Card

•

One Metal Backplate

1.3Power Specifications

Transformer Input: Primary input: 120 VAC, 60 Hz, Secondary output: 16 VAC 56 VA

Standby Battery:

12

VDC, 1.0 Amps Max. charging current

Auxiliary:

12

VDC output at 1.0 Amp Max*

Bell Output:

12

VDC at .7 Amp Max*

Note: The combined Auxiliary and Bell outputs total cannot exceed 1.9 Amps with a 56 VA Transformer.

All circuits are inherent Power Limited except the red battery wire and AC terminal.

*For Commercial Fire installations, see the Compliance Instructions section.

1.4Communication

Built-in dialer or network communication to DMP Model SCS-1R Receivers Built-in Contact ID communication to non-DMP receivers

893A Dual Phone Line Module with phone line supervision

Can operate as a local panel

1.5Panel Zones

Eight 1k Ohm EOL burglary zones (zones 1 to 8). Connect to 869 Class A module for burglary applications. Two 3.3k Ohm EOL powered zone with reset (zones 9 and 10).

Note: Use the supplied DMP Model 311 1k Ohm and DMP Model 301 3.3k Ohm resistors.

1.6Keypad Bus

You can connect up to 15 of the following supervised keypads and expansion modules to the keypad bus:

•Alphanumeric Fire Command Centers or keypads

•Four- and/or single-zone expansion modules

•Single-zone detectors

•Access control modules

XR2500F Installation Guide

Digital Monitoring Products

1

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Installation Guide Model XR2500F Command Processor Installation Guide Fire Command Center Secondary Power SupplyIntroduction MountingBattery Information Accessory DevicesPowered Zones for 2-Wire Smoke Detectors J22 LX-Bus Expansion ConnectorReset and Tamper Headers J1 Ethernet ConnectorListed Compliance Specifications Universal UL Burglary SpecificationsDigital Burglar Alarm Communicator System Units ANSI/ UL Holdup Alarm UnitsPolice Station Connected and Local Burglar Alarm Units Access Control System UnitsNew York City MEA Specifications California State Fire Marshal SpecificationsWiring Diagrams Household Fire Warning System Units ANSI/UL 985, NfpaThis page intentionally left blank Introduction Outputs LX-BusRelays Zone ReferenceMounting Use Marking Wiring DiagramAC Connection Transformers and AC Power Connection16 VAC Transformer Earth Ground GNDSecondary Power Supply Battery Connection to XR2500F Command Processor panelDescription Two 866 NAC Modules ConnectionBell Silence/Bell Trouble LX-Bus Operation Installing the 481 CardXR2500F On-board LX-Bus LX-Bus 481 Zone Expansion Interface Card893A Dual Phone Line Module FCC Registration NotificationRemote Fire Command Center Fire Command CenterExpansion Zone ExpansionOutput Expansion Lightning Protection Accessory DevicesAccessory Devices Mounting Keypads and Zone Expansion Modules Connecting LX-Bus and Keypad Bus DevicesBattery Information Copy Sub-Totals to next 11.7 XR2500F Standby Battery CalculationsThis page only Standby Battery Selection Keypad Bus Bell OutputSmoke and Glassbreak Detector Output Powered Zones for 2-Wire Smoke DetectorsTerminals 11 Current RatingDS250HD Compatible 2-Wire Smoke Detector ChartProtection Zones Keyswitch Arming ZoneTerminals Operational ParametersOutput Harness Wiring Dry Contact Relay OutputsContact Rating J11 Annunciator Outputs Model 300 Harness WiringJ23 6-Pin Header Model 860 Relay ModuleJ21 Serial Connector J22 LX-Bus Expansion ConnectorSerial Connector LEDs LX-Bus Interface CardsReset and Tamper Headers J1 Ethernet Connector23.1 J16 Reset Header Ethernet LEDsUniversal UL Burglary Specifications Listed Compliance SpecificationsArea Information Household Burglar-Alarm System Units ANSI/ULDact Central Station Proprietary DialerStandard or Encrypted Line Security Model 463G Cell Only, Standard or Encrypted Line SecurityPath 1 programming Path 2 programming Path 3 programming Holdup Alarm Units Digital Burglar Alarm Communicator System Units ANSI/ ULPolice Station Connected and Local Burglar Alarm Units Automatic Bell Test BellPath 1 programming Path 2 programming Path 3 programming Mercantile Access Control System UnitsPanel Designation Compatible DevicesUniversal Fire Alarm Specifications Power Fail Delay Power SupplyLocal Protective Signaling Systems Remote Station Protective Signaling SystemsHousehold Fire Warning System Units ANSI/UL 985, Nfpa Ground FaultNotification Appliances Cross ZoningNew York City MEA Specifications California State Fire Marshal SpecificationsDigital Dialer and Network Communication Communication ProgrammingPrewired 866 Modules with NAC Extender Wiring DiagramsWiring Diagrams Alarm Bell PWR Bell Out + Bell Trouble DSM-12/24 Module To initiating zone 39.5 867 Class B Style W Notification Appliance CircuitTo initiating zone DMP Model Dual Style D Zone Module Installation Remote Station Reversing Relay Connection Command Processor PanelXR2500F 481 Command Processor Panel Second LX-Bus with Auxiliary Power SupplyLX-Bus Module Connection Model 860 Relay Module Connection Powered Burglary DevicesVer Section Number and Heading Quick Explanation of Changes Revisions to This DocumentThis page intentionally left blank Mounting Instructions Listings and Approvals Operating Instructions Model XR2500F Panels

XR2500F specifications

The DMP Electronics XR2500F is an advanced and versatile electronic device designed to cater to a wide range of applications including industrial automation, robotics, and smart home technologies. Known for its robust performance and reliable functionalities, the XR2500F stands out as a leading option in the market.

One of the main features of the XR2500F is its powerful processing unit, which ensures efficient handling of complex tasks and data processing. With a clock speed of up to 2.5 GHz, the device is capable of multitasking, enabling users to run multiple applications simultaneously without compromising performance. This makes the XR2500F an ideal choice for applications that require real-time data processing and analysis.

The XR2500F is equipped with an extensive array of connectivity options, including Wi-Fi, Bluetooth, and Ethernet capabilities. This allows for seamless integration with various devices and networks. The wireless options facilitate easy communication with cloud services and other IoT devices, making it suitable for smart home automation systems, where synchronization and control are critical.

In terms of memory, the XR2500F offers significant storage capacity, with options that can accommodate up to 64GB of RAM and 512GB of flash storage. This ample memory ensures that users can store large amounts of data and run memory-intensive applications without experiencing slowdowns. Additionally, the device supports expandable memory options, allowing for future upgrades to meet growing demands.

The XR2500F also incorporates advanced security technologies to protect sensitive data. Features like end-to-end encryption and secure boot processes safeguard against unauthorized access and data breaches. This is particularly important in industrial settings where data integrity is critical for operational safety.

Another remarkable characteristic of the XR2500F is its energy efficiency. Designed with the latest power management technologies, the device minimizes energy consumption while maximizing performance. This not only reduces operational costs but also aligns with green technology initiatives.

Overall, the DMP Electronics XR2500F is a high-performance electronic device that combines powerful processing, extensive connectivity, robust memory, enhanced security, and energy efficiency. Its versatility and reliability make it a preferred choice for professionals seeking innovative solutions in automation and control systems.
Top Page Image Contents