Hearth and Home Technologies II-B owner manual Junction Box Installation

Page 20

E. Junction Box Installation

If the box is being wired from the OUTSIDE of the appliance:

Install the Romexconnector (not included with appliance) in the side wrap.

Loosen two screws on the Romex connector, feed the necessary length of wire through the connector and tighten the screws.

Make all necessary wire connections.

If the box is being wired from the INSIDE of the appliance:

Remove the screw attaching the junction box to the outer shell, rotate the junction box inward to disengage it from the outer shell (see Figure 7.4).

Pull the electrical wires from outside the appliance through this opening into the valve compartment.

 

HEAT SHIELD

 

 

 

14/2WG

 

 

COPPER GROUND

WHT

BLK

ATTACHED TO GRN SCREW

 

 

WITH GRN WIRE

 

BLK

GREEN WIRE

WHT

 

 

INSIDE BOX

 

 

NOTE: Do NOT wire

Figure 7.4 Junction Box Detail

110 VAC to wall switch.

 

Loosen the two screws on the Romex connector, feed the necessary length of wire through the connector and tighten the screws.

Make all necessary wire connections to the receptacle and assemble the receptacle and cover to the junction box.

F.Wall Switch Installation for Fan (Optional)

If the box is being wired to a wall mounted switch for use with a fan (See Figure 7.5):

The power supply for the appliance must be brought into a switch box.

The power can then be supplied from the switch box to the appli- ance using a minimum of 14-3 with ground wire.

At the switch box connect the black (hot) wire and red (switch leg) wire to the wall switch as shown.

At the appliance connect the black (hot), white (neutral) and green (ground) wires to the junction box as shown.

Add a 1/4 inch insulated female connector to the red (switch leg) wire, route it through the knockout in the face of the junction box, and connect to the top fan switch con- nector (1/4 inch male) as shown.

6 INCH

 

 

APPROX.

 

 

FAN

WIRE LEAD

 

SPEED CONTROL

 

1 MALE END

 

(RHEOSTAT)

 

1 FEMALE END

 

 

 

 

TEMPERATURE

 

 

SENSOR SWITCH

 

 

WIRE LEAD

 

 

2 FEMALE ENDS

JUNCTION

 

 

BOX

 

6 INCH

 

 

APPROX.

 

FAN

 

 

PLUG AND WIRE

 

 

ASSEMBLY

 

 

 

OPTIONAL

 

Figure 7.5 Junction Box Wired to Wall Switch

WALL SWITCH

 

 

 

20

Heat & Glo LifeStyle Collection • Twilight-II-B2108-900 Rev. G • 8/07

Image 20
Contents Model Twilight-II-B Congratulations Homeowner Reference InformationTable of Contents Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of MassachusettsDesign and Installation Considerations Getting StartedTools and Supplies Needed Inspect Appliance and ComponentsFraming and Clearances Selecting Appliance LocationClearances Fire Risk Odor RiskMantel Projections Indoor only CeilingTermination Locations Appliance Opening Minimum ClearancesRemoving Non-combustible Facing Material Assembly Appliance PreparationSecuring and Leveling the Appliance Placing Metal Hearth StripPlacing and Securing Appliance Placing Flashing and SheathingApply housewrap or building paper Risk of FireInstalling Non-combustible Facing Material Outdoor Side 19 Attaching Non-combustible Facing MaterialGas Information Fuel Conversions Gas ConnectionGas Pressures Pressure Natural Gas PropaneHigh Altitude Installations Electrical Information Recommendation for WireConnecting to the Appliance Optional Accessories Fan locationIntellifire Ignition System Wiring Optional Accessories RequirementsJunction Box Installation Wall Switch Installation for Fan OptionalFacing Material FinishingMantel Projections Risk of Fire Detail Appliance Setup Clean the ApplianceAccessories Lava Rock and Ember PlacementInch Log Set Assembly LOGS-TWIPositioning the Logs Sharp Notch Smooth Cutout Sharp NotchGlass Assembly Shutter SettingsRemoving Glass Assembly Replacing Glass AssemblyOperating Instructions Before Lighting ApplianceLighting Appliance Intellifire IgnitionAfter Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure Sympton Possible Cause Corrective Action TroubleshootingIntellifire Ignition System Symptom Possible Cause Corrective Action Maintenance Tasks Maintaining and Servicing ApplianceInspect Maintenance Tasks Recommend addition of screen if one is not presentAppliance Dimension Diagram Reference MaterialsService Parts Log Set AssemblyService Parts List IPI Valve Assembly Limited Lifetime Warranty Limited Lifetime Warranty Heat & GLO GAS Appliance ProductsContact Information Do not Discard this Manual