Hearth and Home Technologies C-40 warranty Frame the Fireplace, Minimum Clearances to Combustibles

Page 12

1. Minimum Clearances to Combustibles

WITHIN ENCLOSURE AREA:

 

 

 

Appliance to backwall

1 in. (25 mm)

 

Appliance to sidewall

1 in. (25 mm)

 

Duct boots to framing

0 in. (0 mm)

 

Top standoffs to header

0 in. (0 mm)

 

Door opening to sidewall

22-7/8 in. (581 mm)

EXPOSED SURFACES

 

 

 

Faceplate to sidewall

16 in. (406 mm)

 

Heat zone air grills to ceiling

12 in. (305 mm)

 

MANTEL

Combustible and non-combustible mantel minimum height from base of fireplace to underside of mantel

60 in. (1524 mm)

Maximum mantel depth

12 in. (305 mm)

Optional Framing Construction / Reduced

Mantel Height:

Non-combustible mantel material minimum height from base of fireplace to underside of mantel 46 in. (1168mm) when the following enclosure construction materials are used:

Non-combustible framing materials must be used above fire- place to height of 84 in. (2134mm) from base of fireplace for all construction materials, framing members, sheeting, and all finish materials.

Non-Combustible Materials

Materials which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136, Stan- dard Test Method for Behavior of Materials, in a Vertical Tube Furnace at 750°C, shall be considered non-combus-

WARNING

Fire Risk

•Non-combustible mantels installed at a reduced height may GET EXTREMELY HOT during use of the fireplace.

•DO NOT TOUCH or place heat sensitive combustible items on the mantel.

CHIMNEY SECTIONS

Chimney sections at any level require a 2 in. (51 mm) mini- mum air space clearance between the framing and chimney section.

C. Frame the Fireplace

NOTE: Wiring for fans must be done before framed enclosure is completed. If using a Heat Zone kit, it also must be installed before enclosure is complete.

The Constitution Fireplace will fit a framed opening height of 43-7/8 in. (1114 mm) tall and width of 42 in. (1067 mm). The finished cavity depth must be no less than 24 in. (610 mm). Framing must extend straight up all the way to the ceiling.

Figure 12.1 shows a typical framing (using 2 x 4 lumber) of the fireplace, assuming combustible materials are used. All required clearances to combustibles around the fireplace must be adhered to. See Figure 11.1, on page 11. Any fram- ing across the top of the fireplace must be above the level of the top standoffs. (No recess above standoffs.)

2 in.

(51mm)

tible materials.

Combustible Materials

Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other materials that can ignite and burn, whether flame proofed or not, or whether plastered or un-plastered shall be considered combustible materials.

WARNING

Fire Risk

Hearth & Home Technologies is not respon- sible for discoloration, cracking or other mate-

43-7/8 in.

(1114mm)

24 in.

(610mm)

12 in.

(305mm)

Position combustible / non-combustible mantel 60 in. (1524mm) from base of the fireplace

42 in.

(1067mm)

rial failures of finishing materials due to heat exposure or smoke.

•Choose finishing materials carefully.

Figure 12.1 Framing the Fireplace

Page 12

Heatilator • Constitution EPA Fireplace • 480-1091C

November 11, 2008

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Installation and Operation Hot glass will cause burnsFire Risk Listing Label Information/Location Serial No Model Name Test Lab Report No Manufactured DateTable of Contents Listing and Code Approvals Appliance CertificationMobile Home Approved Glass Specifications BTU & Efficiency SpecificationsDesign and Installation Considerations Getting StartedNegative Pressure Asphyxiation RiskNovember 11 Heatilator Constitution EPA Fireplace 480-1091C Typical Fireplace System Typical Fireplace SystemTools and Supplies Needed Inspect Fireplace and ComponentsFire Risk Explosion Risk Framing and Clearances Selecting Fireplace LocationModel Constitution Clearances Clearances to Combustible MaterialsFrame the Fireplace Minimum Clearances to CombustiblesOptional Framing Construction / Reduced Mantel Height Non-Combustible MaterialsElectrical Access and Wiring Diagram SuggestionsConstruct the Chase MaterialsInstallation of Fireplace Install the Outside Air KitFire Risk Asphyxiation Risk Risk of Smoke SpillageHandle Left Closed Handle Right OpenSecure the Fireplace Position the FireplacePlace the Protective Metal Hearth Strips Level the Fireplace Position the Protective Metal Hearth StripsChimney Assembly Chimney Requirements Chimney Termination RequirementsUsing Offsets/Returns ExampleInstalling CAK4A and Flex Pipe Assemble the Chimney SectionsAssembling Chimney Sections for the SL- 300 Series Install the Ceiling Firestops Installing Flex PipeInstall the Attic Insulation Shield Double-check the Chimney AssemblySecure the Chimney Complete the Enclosure Chimney Termination 2-10-3 RuleChimney Termination Requirements See Figures 25.1 Slanted RoofsInstall the Roof Flashing Install the Chimney Air Kit required in CanadaMark the Exit Point of the Roof Cut Out the Hole in the RoofSL-300 Series Ceiling/Roof Thimble Consult local codes for framing detailsInstall the Termination Cap Chase TopChase Top Framing ‑1/2 in mm below the chase top. See Figure Accessories Fan ReplacementFan Replacement Instructions Shock RiskBaffle Removal and Installation Door and Door GasketHeat Zone Kit Minimum Clearance to CombustiblesRun Length Cut Pipe Ft 6-12m 20 ft 3 6m 10 ft 1 3m No cut needed4 wall Timer Assembly Replacement Timer AssemblyRemove & Replace Timer Manual Timer Override Timer Override LeverFinishing Hearth ExtensionCalculating Alternate Floor Protection Material Model # Constitution 1041 508 Positioning the Protective Metal Hearth StripsFascia Outer Tile or Marble Combustible Can Flange Floor Position the Hearth Extension Finishing Material Non-Combustible Facing Material Installation Risk of FireMantel Specifications MantelSymptoms of Over-Firing Operating InstructionsOver-Firing Your Appliance General InformationOutside Air Keep open during useClear Space Near the Fireplace FirescreenGlass Doors Fan OperationMoisture content Wood Fuel Hardwood vs. SoftwoodSeasoning Storing Wood Starting a FireFire Risk Correct Baffle & Blanket Placement Incorrect PositionsBurning Process Automatic Combustion Control ACCBurning Guidelines Burn RatesOpacity Burn Rate BTU / Hr Slide Air ControlFire Safety Chimney FireTroubleshooting Understanding Vent ProblemsDraft Problems Factory-built Fireplaces Troubleshooting Diagnostics and Problem Solving Diagnostic Question Possible Causes of Condition SolutionsDon’t get enough/any heat. What can I do about it? Maintenance and Servicing the Fireplace General MaintenanceClean Creosote Chimney CleaningGlass Replacement Glass CleaningDisposal of Ashes Fire Risk Injury RiskFirebrick Replacement Care and Cleaning of Plated Surfaces Maintenance Task ListInspect Maintenance Tasks Service & Maintenance Log Date of Service Performed By Description of ServiceFireplace Dimensions Reference MaterialsConstitution Chimney Components 15-3/4 Parts Diagram NorthStar Fireplace DiagramService Parts Constitution FPBeginning Manufacturing Date Ending Manufacturing DateSL1 Description Comments Serial Number DateThis page intentionally left blank Warranty Policy Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHearth & Home Technologies Limited Warranty Cont’d Contact Information Do not Discard this Manual

C-40 specifications

Hearth and Home Technologies (HHT) has long been known for its commitment to innovation and quality in the heating and home comfort industry. One of their standout offerings is the C-40, a versatile and efficient gas fireplace that embodies the brand’s dedication to modern aesthetics and advanced technology. This fireplace is designed to not only provide warmth but also enhance the ambiance of any living space.

The C-40 features a sleek, contemporary design that can seamlessly fit into various interior styles. Its clean lines and minimalist frame allow it to serve as a stylish focal point in a room, while offering the functionality and performance that homeowners expect from a high-quality gas fireplace. The unit is available in various configurations, including built-in and wall-mounted options, allowing for flexibility in installation and design.

One of the most notable features of the C-40 is its impressive heat output. With the ability to deliver efficient and evenly distributed warmth, this gas fireplace can effectively heat spaces of various sizes, making it an excellent choice for both small and large rooms. The adjustable flame height feature further enhances the user experience, allowing homeowners to customize their heating preference and create the perfect atmosphere for any occasion.

The C-40 is equipped with cutting-edge technologies, including electronic ignition and a remote control system, making it convenient and easy to use. The electronic ignition ensures quick and reliable startup, while the remote control allows for effortless temperature and flame adjustment from anywhere in the room. This added convenience is a significant benefit for those who value comfort and ease of operation.

Additionally, the C-40 incorporates advanced safety features, such as an automatic shut-off and a secure glass front, providing peace of mind for families. The glass front not only enhances safety but also serves to display the mesmerizing flames beautifully, allowing everyone to enjoy its warmth and glow.

In summary, Hearth and Home Technologies’ C-40 is a prime example of combining stylish design with modern technology and efficiency. Its exceptional heat output, customizable features, and advanced safety measures make it a standout choice for homeowners looking to enhance their living spaces with a dependable gas fireplace. Whether for cozy family gatherings or quiet evenings at home, the C-40 offers both aesthetic appeal and functional excellence, ensuring it remains a popular choice in contemporary home design.
Top Page Image Contents