Hearth and Home Technologies C-40 Maintenance and Servicing the Fireplace, General Maintenance

Page 58

11 Maintenance and Servicing the Fireplace

WARNING

Asphyxiation Risk

Fire Risk

Annual inspection by qualified technician recommended.

Check:

•Condition of doors, surrounds and fronts

•Condition of glass and glass assembly

•Obstructions of combustion and ventilation air

•Obstructions of termination cap

Clean:

•Glass

•Air passageways, grilles

A.General Maintenance

1.Creosote (Chimney) Cleaning

•Frequency: As necessary; at least annually before lighting stove or once every 2 months during heating season.

•By: Homeowner / Chimney Sweep

•Task: See the following instructions.

Remove all ash from the firebox and extinguish all hot embers before disposal. Allow the appliance to cool completely. Disconnect flue pipe or remove baffle and ceramic blanket from appliance before cleaning chimney. Otherwise residue can pile up on top of the baffle and ceramic blanket and the appliance will not work properly. (See Baffle Removal on page 31). Close the door tightly. The creosote or soot should be removed with a brush specifically designed for the type of chimney in use. Clean out fallen ashes from the firebox. A chimney sweep can perform this service.

It is also recommended that before each heating season the entire system be professionally inspected, cleaned and repaired if necessary.

Inspection: Inspect the system at the appliance connection and at the chimney top. Cooler surfaces tend to build creosote deposits quicker, so it is important to check the chimney from the top as well as from the bottom.

Formation and Need For Removal: When wood is burned slowly, it produces tar and other organic vapors which combine with expelled moisture to form creosote. The creosote vapors condense in the relatively cool chimney flue of a newly-started or a slow-burning fire. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote creates an extremely hot fire which may damage the chimney or even destroy the house. The chimney connector and chimney should be inspected once every 2 months during the heating season to determine if a creosote or soot buildup has occurred. If creosote or soot has accumulated, it should be removed to reduce the risk of a chimney fire.

Remove 8 screws (9 for King), lift top cover.

Cap Top

(Be sure holes in cap top and cap base are aligned.)

Cap Base

European Copper Series

Termination Cap (CT3-King shown)

Remove screws, lift top cover.

Top Cover

Cap

Chimney

TR344/TR342

Round

Termination Cap

Remove 4 screws and lift top pan off.

Cap

Slip

Section

ST375

Square

Termination Cap

1.Remove the 4 screws.

2.Remove the screen.

3.Remove the baffle.

Cap

Chase

TS345/TS345P

Square

Termination Caps

Remove 2 screws from the front and back and lift the top off.

TCT375

Terra Cotta

Termination Cap

Figure 58.1 Chimney & Termination Cap Cleaning

Page 58

Heatilator • Constitution EPA Fireplace • 480-1091C

November 11, 2008

Page 57 Page 59
Image 58
Page 57 Page 59
Contents Hot glass will cause burns Installation and OperationFire Risk Listing Label Information/Location Serial No Model Name Test Lab Report No Manufactured DateTable of Contents Appliance Certification Listing and Code ApprovalsMobile Home Approved Glass Specifications BTU & Efficiency SpecificationsNegative Pressure Design and Installation ConsiderationsGetting Started Asphyxiation RiskNovember 11 Heatilator Constitution EPA Fireplace 480-1091C Typical Fireplace System Typical Fireplace SystemInspect Fireplace and Components Tools and Supplies NeededFire Risk Explosion Risk Selecting Fireplace Location Framing and ClearancesModel Constitution Clearances Clearances to Combustible MaterialsOptional Framing Construction / Reduced Mantel Height Frame the FireplaceMinimum Clearances to Combustibles Non-Combustible MaterialsElectrical Access and Wiring Diagram SuggestionsConstruct the Chase MaterialsInstallation of Fireplace Install the Outside Air KitHandle Left Closed Fire Risk Asphyxiation RiskRisk of Smoke Spillage Handle Right OpenPosition the Fireplace Secure the FireplacePlace the Protective Metal Hearth Strips Level the Fireplace Position the Protective Metal Hearth StripsChimney Assembly Chimney Requirements Chimney Termination RequirementsUsing Offsets/Returns ExampleAssemble the Chimney Sections Installing CAK4A and Flex PipeAssembling Chimney Sections for the SL- 300 Series Install the Ceiling Firestops Installing Flex PipeDouble-check the Chimney Assembly Install the Attic Insulation ShieldSecure the Chimney Chimney Termination Requirements See Figures 25.1 Complete the EnclosureChimney Termination 2-10-3 Rule Slanted RoofsMark the Exit Point of the Roof Install the Roof FlashingInstall the Chimney Air Kit required in Canada Cut Out the Hole in the RoofSL-300 Series Ceiling/Roof Thimble Consult local codes for framing detailsChase Top Install the Termination CapChase Top Framing ‑1/2 in mm below the chase top. See Figure Fan Replacement Instructions AccessoriesFan Replacement Shock RiskBaffle Removal and Installation Door and Door GasketHeat Zone Kit Minimum Clearance to CombustiblesRun Length Cut Pipe Ft 6-12m 20 ft 3 6m 10 ft 1 3m No cut needed4 wall Timer Assembly Replacement Timer AssemblyRemove & Replace Timer Manual Timer Override Timer Override LeverHearth Extension FinishingCalculating Alternate Floor Protection Material Model # Constitution 1041 508 Positioning the Protective Metal Hearth StripsFascia Outer Tile or Marble Combustible Can Flange Floor Position the Hearth Extension Finishing Material Non-Combustible Facing Material Installation Risk of FireMantel Specifications MantelOver-Firing Your Appliance Symptoms of Over-FiringOperating Instructions General InformationOutside Air Keep open during useGlass Doors Clear Space Near the FireplaceFirescreen Fan OperationWood Fuel Hardwood vs. Softwood Moisture contentSeasoning Storing Wood Starting a FireFire Risk Correct Baffle & Blanket Placement Incorrect PositionsBurning Process Automatic Combustion Control ACCOpacity Burning GuidelinesBurn Rates Burn Rate BTU / Hr Slide Air ControlFire Safety Chimney FireUnderstanding Vent Problems TroubleshootingDraft Problems Factory-built Fireplaces Troubleshooting Diagnostics and Problem Solving Diagnostic Question Possible Causes of Condition SolutionsDon’t get enough/any heat. What can I do about it? Clean Maintenance and Servicing the FireplaceGeneral Maintenance Creosote Chimney CleaningDisposal of Ashes Glass ReplacementGlass Cleaning Fire Risk Injury RiskFirebrick Replacement Maintenance Task List Care and Cleaning of Plated SurfacesInspect Maintenance Tasks Service & Maintenance Log Date of Service Performed By Description of ServiceReference Materials Fireplace DimensionsConstitution Chimney Components 15-3/4 Parts Diagram NorthStar Fireplace DiagramBeginning Manufacturing Date Service PartsConstitution FP Ending Manufacturing DateSL1 Description Comments Serial Number DateThis page intentionally left blank Warranty Policy Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHearth & Home Technologies Limited Warranty Cont’d Contact Information Do not Discard this Manual

C-40 specifications

Hearth and Home Technologies (HHT) has long been known for its commitment to innovation and quality in the heating and home comfort industry. One of their standout offerings is the C-40, a versatile and efficient gas fireplace that embodies the brand’s dedication to modern aesthetics and advanced technology. This fireplace is designed to not only provide warmth but also enhance the ambiance of any living space.

The C-40 features a sleek, contemporary design that can seamlessly fit into various interior styles. Its clean lines and minimalist frame allow it to serve as a stylish focal point in a room, while offering the functionality and performance that homeowners expect from a high-quality gas fireplace. The unit is available in various configurations, including built-in and wall-mounted options, allowing for flexibility in installation and design.

One of the most notable features of the C-40 is its impressive heat output. With the ability to deliver efficient and evenly distributed warmth, this gas fireplace can effectively heat spaces of various sizes, making it an excellent choice for both small and large rooms. The adjustable flame height feature further enhances the user experience, allowing homeowners to customize their heating preference and create the perfect atmosphere for any occasion.

The C-40 is equipped with cutting-edge technologies, including electronic ignition and a remote control system, making it convenient and easy to use. The electronic ignition ensures quick and reliable startup, while the remote control allows for effortless temperature and flame adjustment from anywhere in the room. This added convenience is a significant benefit for those who value comfort and ease of operation.

Additionally, the C-40 incorporates advanced safety features, such as an automatic shut-off and a secure glass front, providing peace of mind for families. The glass front not only enhances safety but also serves to display the mesmerizing flames beautifully, allowing everyone to enjoy its warmth and glow.

In summary, Hearth and Home Technologies’ C-40 is a prime example of combining stylish design with modern technology and efficiency. Its exceptional heat output, customizable features, and advanced safety measures make it a standout choice for homeowners looking to enhance their living spaces with a dependable gas fireplace. Whether for cozy family gatherings or quiet evenings at home, the C-40 offers both aesthetic appeal and functional excellence, ensuring it remains a popular choice in contemporary home design.
Top Page Image Contents