Hearth and Home Technologies C-40 warranty Outside Air, Keep open during use

Page 45

C. Outside Air

A source of air (oxygen) is required in order for combustion to take place. Whatever air is consumed by the fire must be replaced through cracks around windows, under doors, etc. Most newly constructed houses or existing homes fitted with tightly sealed doors and windows are relatively air tight. In this case, an outside air source must be made available to feed combustion air from outside the home.

The Constitution Fireplace comes equipped with an outside air intake to feed combustion air from outside the home, along with an outside air termination cap. The 6 in. (152 mm) solid/flex pipe is not supplied.

Outside air is required to minimize the effects of negative pressure within the structure. It is recommended to utilize the shortest duct run to optimize the performance of the Out- side Air flex tubing. The outside air inlet thimble should be positioned above the ground level, and must remain clear of leaves, debris, ice and/or snow. If you live in an area that experiences deep snow levels, this must be taken into con- sideration when determining the height placement above ground level. It must be unrestricted while unit is in use to prevent room air starvation which can cause smoke spillage and an inability to maintain a fire. Smoke spillage can also set off smoke alarms.

This fireplace will operate correctly only if adequate ventilation is provided to allow proper draft to the fire- place system. Hearth & Home Technologies assumes no responsibility for the improper performance of the fireplace system caused by inadequate draft due to environmental conditions, down drafts, tight sealing construction of the structure, or mechanical exhaust- ing devices which create a negative air pressure within the structure where the fireplace is located.

NOTE: OUTSIDE AIR IS REQUIRED.

An outside air control handle allows you control of the out- side air inlet. This may be closed only when the fireplace is not in use to prevent cold air infiltration. Use of outside air for combustion is required to conserve heated air within the structure and to provide make up air to keep the fireplace venting properly.

See Figure 45.1, for location and operation.

CAUTION

Outside air control handle may be warm. Adjust before lighting fire.

 

Automatic Combustion

 

 

 

Control Handle

 

 

 

Outside Air Control

 

 

 

Handle

 

 

 

Keep open during use.

 

 

Figure 45.1 General Operating Parts

 

 

November 11, 2008

Heatilator • Constitution EPA Fireplace • 480-1091C

Page

45

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Installation and Operation Hot glass will cause burnsFire Risk Serial No Model Name Test Lab Report No Manufactured Date Listing Label Information/LocationTable of Contents Listing and Code Approvals Appliance CertificationMobile Home Approved BTU & Efficiency Specifications Glass SpecificationsGetting Started Design and Installation ConsiderationsNegative Pressure Asphyxiation RiskNovember 11 Heatilator Constitution EPA Fireplace 480-1091C Typical Fireplace System Typical Fireplace SystemTools and Supplies Needed Inspect Fireplace and ComponentsFire Risk Explosion Risk Framing and Clearances Selecting Fireplace LocationModel Constitution Clearances to Combustible Materials ClearancesMinimum Clearances to Combustibles Frame the FireplaceOptional Framing Construction / Reduced Mantel Height Non-Combustible MaterialsSuggestions Electrical Access and Wiring DiagramMaterials Construct the ChaseInstall the Outside Air Kit Installation of FireplaceRisk of Smoke Spillage Fire Risk Asphyxiation RiskHandle Left Closed Handle Right OpenSecure the Fireplace Position the FireplacePlace the Protective Metal Hearth Strips Position the Protective Metal Hearth Strips Level the FireplaceChimney Assembly Chimney Termination Requirements Chimney RequirementsExample Using Offsets/ReturnsInstalling CAK4A and Flex Pipe Assemble the Chimney SectionsAssembling Chimney Sections for the SL- 300 Series Installing Flex Pipe Install the Ceiling FirestopsInstall the Attic Insulation Shield Double-check the Chimney AssemblySecure the Chimney Chimney Termination 2-10-3 Rule Complete the EnclosureChimney Termination Requirements See Figures 25.1 Slanted RoofsInstall the Chimney Air Kit required in Canada Install the Roof FlashingMark the Exit Point of the Roof Cut Out the Hole in the RoofConsult local codes for framing details SL-300 Series Ceiling/Roof ThimbleInstall the Termination Cap Chase TopChase Top Framing ‑1/2 in mm below the chase top. See Figure Fan Replacement AccessoriesFan Replacement Instructions Shock RiskDoor and Door Gasket Baffle Removal and InstallationMinimum Clearance to Combustibles Heat Zone Kit20 ft 3 6m 10 ft 1 3m No cut needed Run Length Cut Pipe Ft 6-12m4 wall Timer Assembly Timer Assembly ReplacementRemove & Replace Timer Timer Override Lever Manual Timer OverrideFinishing Hearth ExtensionCalculating Alternate Floor Protection Material Positioning the Protective Metal Hearth Strips Model # Constitution 1041 508Fascia Outer Tile or Marble Combustible Can Flange Floor Position the Hearth Extension Finishing Material Risk of Fire Non-Combustible Facing Material InstallationMantel Mantel SpecificationsOperating Instructions Symptoms of Over-FiringOver-Firing Your Appliance General InformationKeep open during use Outside AirFirescreen Clear Space Near the FireplaceGlass Doors Fan OperationMoisture content Wood Fuel Hardwood vs. SoftwoodSeasoning Starting a Fire Storing WoodFire Risk Incorrect Positions Correct Baffle & Blanket PlacementAutomatic Combustion Control ACC Burning ProcessBurn Rates Burning GuidelinesOpacity Burn Rate BTU / Hr Slide Air ControlChimney Fire Fire SafetyTroubleshooting Understanding Vent ProblemsDraft Problems Factory-built Fireplaces Troubleshooting Diagnostic Question Possible Causes of Condition Solutions Diagnostics and Problem SolvingDon’t get enough/any heat. What can I do about it? General Maintenance Maintenance and Servicing the FireplaceClean Creosote Chimney CleaningGlass Cleaning Glass ReplacementDisposal of Ashes Fire Risk Injury RiskFirebrick Replacement Care and Cleaning of Plated Surfaces Maintenance Task ListInspect Maintenance Tasks Date of Service Performed By Description of Service Service & Maintenance LogFireplace Dimensions Reference MaterialsConstitution Chimney Components 15-3/4 NorthStar Fireplace Diagram Parts DiagramConstitution FP Service PartsBeginning Manufacturing Date Ending Manufacturing DateDescription Comments Serial Number Date SL1This page intentionally left blank CONDITIONS, Exclusions & Limitation of Liability Warranty Policy Hearth & Home Technologies Limited WarrantyHearth & Home Technologies Limited Warranty Cont’d Do not Discard this Manual Contact Information

C-40 specifications

Hearth and Home Technologies (HHT) has long been known for its commitment to innovation and quality in the heating and home comfort industry. One of their standout offerings is the C-40, a versatile and efficient gas fireplace that embodies the brand’s dedication to modern aesthetics and advanced technology. This fireplace is designed to not only provide warmth but also enhance the ambiance of any living space.

The C-40 features a sleek, contemporary design that can seamlessly fit into various interior styles. Its clean lines and minimalist frame allow it to serve as a stylish focal point in a room, while offering the functionality and performance that homeowners expect from a high-quality gas fireplace. The unit is available in various configurations, including built-in and wall-mounted options, allowing for flexibility in installation and design.

One of the most notable features of the C-40 is its impressive heat output. With the ability to deliver efficient and evenly distributed warmth, this gas fireplace can effectively heat spaces of various sizes, making it an excellent choice for both small and large rooms. The adjustable flame height feature further enhances the user experience, allowing homeowners to customize their heating preference and create the perfect atmosphere for any occasion.

The C-40 is equipped with cutting-edge technologies, including electronic ignition and a remote control system, making it convenient and easy to use. The electronic ignition ensures quick and reliable startup, while the remote control allows for effortless temperature and flame adjustment from anywhere in the room. This added convenience is a significant benefit for those who value comfort and ease of operation.

Additionally, the C-40 incorporates advanced safety features, such as an automatic shut-off and a secure glass front, providing peace of mind for families. The glass front not only enhances safety but also serves to display the mesmerizing flames beautifully, allowing everyone to enjoy its warmth and glow.

In summary, Hearth and Home Technologies’ C-40 is a prime example of combining stylish design with modern technology and efficiency. Its exceptional heat output, customizable features, and advanced safety measures make it a standout choice for homeowners looking to enhance their living spaces with a dependable gas fireplace. Whether for cozy family gatherings or quiet evenings at home, the C-40 offers both aesthetic appeal and functional excellence, ensuring it remains a popular choice in contemporary home design.
Top Page Image Contents