Hearth and Home Technologies C-40 warranty wall

Page 34

2 x 4 Wall

Fan Housing

2 x 4 wall

1/2 in. (13mm) clearance to combustibles must be maintained.

Sheet Rock

Figure 34.1

Secure B-Vent to Fan Housing with sheet metal screws

 

Bracket

 

Can rotate

 

180o

Return Air Grille

Securely Twist

Install with Louvers

Lock B-Vent to

pointed down

Adapter

Figure 34.2

NOTE: Secure the duct so that clearance to the fire- place outer wrap is maintained. Tape all seams with aluminum tape 1-1/4 in. (32mm) minimum width or as specified by local codes.)

10.Seal all the way around the inside of the Return Air Grille to prevent hot air being drawn back into the venting system using gasketing supplied with the kit. Leave 1/4 in. (6mm) clearance from all 4 outer edges. Trim excess gasketing. See Figure 34.3.

Leave 1/4" (6mm) clearance from all 4 outer edges

Figure 34.3

11.Install the variable speed wall rheostat (with setting on

“OFF”) in a convenient location. This switch will control the

Heat-Zone fan operation.

12.Remove the Junction Box. Wire 110 VAC service TO the wall rheostat and FROM the wall rheostat to the fan Junction

Box. Use wire nuts to secure the 110 VAC service wires to the hot (black) and neutral (white) fan wires and screw the

110VAC ground wire to the Junction Box. See Figure 34.4.

Junction Box

White

Black

Wire Nuts

Wire Clamp

Junction Box Removed

Figure 34.4

13.Secure the Return Air Grille to the fan housing making sure it is flush. The grille must be installed with the louvers pointing down.

NOTE: DO NOT USE ADJUSTABLE REGISTERS.

14. Complete the fireplace installations as per the instruc- tions found in your Owner’s Manual.

Page 34

Heatilator • Constitution EPA Fireplace • 480-1091C

November 11, 2008

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Hot glass will cause burns Installation and OperationFire Risk Listing Label Information/Location Serial No Model Name Test Lab Report No Manufactured DateTable of Contents Appliance Certification Listing and Code ApprovalsMobile Home Approved Glass Specifications BTU & Efficiency SpecificationsNegative Pressure Design and Installation ConsiderationsGetting Started Asphyxiation RiskNovember 11 Heatilator Constitution EPA Fireplace 480-1091C Typical Fireplace System Typical Fireplace SystemInspect Fireplace and Components Tools and Supplies NeededFire Risk Explosion Risk Selecting Fireplace Location Framing and ClearancesModel Constitution Clearances Clearances to Combustible MaterialsOptional Framing Construction / Reduced Mantel Height Frame the FireplaceMinimum Clearances to Combustibles Non-Combustible MaterialsElectrical Access and Wiring Diagram SuggestionsConstruct the Chase MaterialsInstallation of Fireplace Install the Outside Air KitHandle Left Closed Fire Risk Asphyxiation RiskRisk of Smoke Spillage Handle Right OpenPosition the Fireplace Secure the FireplacePlace the Protective Metal Hearth Strips Level the Fireplace Position the Protective Metal Hearth StripsChimney Assembly Chimney Requirements Chimney Termination RequirementsUsing Offsets/Returns ExampleAssemble the Chimney Sections Installing CAK4A and Flex PipeAssembling Chimney Sections for the SL- 300 Series Install the Ceiling Firestops Installing Flex PipeDouble-check the Chimney Assembly Install the Attic Insulation ShieldSecure the Chimney Chimney Termination Requirements See Figures 25.1 Complete the EnclosureChimney Termination 2-10-3 Rule Slanted RoofsMark the Exit Point of the Roof Install the Roof FlashingInstall the Chimney Air Kit required in Canada Cut Out the Hole in the RoofSL-300 Series Ceiling/Roof Thimble Consult local codes for framing detailsChase Top Install the Termination CapChase Top Framing ‑1/2 in mm below the chase top. See Figure Fan Replacement Instructions AccessoriesFan Replacement Shock RiskBaffle Removal and Installation Door and Door GasketHeat Zone Kit Minimum Clearance to CombustiblesRun Length Cut Pipe Ft 6-12m 20 ft 3 6m 10 ft 1 3m No cut needed4 wall Timer Assembly Replacement Timer AssemblyRemove & Replace Timer Manual Timer Override Timer Override LeverHearth Extension FinishingCalculating Alternate Floor Protection Material Model # Constitution 1041 508 Positioning the Protective Metal Hearth StripsFascia Outer Tile or Marble Combustible Can Flange Floor Position the Hearth Extension Finishing Material Non-Combustible Facing Material Installation Risk of FireMantel Specifications MantelOver-Firing Your Appliance Symptoms of Over-FiringOperating Instructions General InformationOutside Air Keep open during useGlass Doors Clear Space Near the FireplaceFirescreen Fan OperationWood Fuel Hardwood vs. Softwood Moisture contentSeasoning Storing Wood Starting a FireFire Risk Correct Baffle & Blanket Placement Incorrect PositionsBurning Process Automatic Combustion Control ACCOpacity Burning GuidelinesBurn Rates Burn Rate BTU / Hr Slide Air ControlFire Safety Chimney FireUnderstanding Vent Problems TroubleshootingDraft Problems Factory-built Fireplaces Troubleshooting Diagnostics and Problem Solving Diagnostic Question Possible Causes of Condition SolutionsDon’t get enough/any heat. What can I do about it? Clean Maintenance and Servicing the FireplaceGeneral Maintenance Creosote Chimney CleaningDisposal of Ashes Glass ReplacementGlass Cleaning Fire Risk Injury RiskFirebrick Replacement Maintenance Task List Care and Cleaning of Plated SurfacesInspect Maintenance Tasks Service & Maintenance Log Date of Service Performed By Description of ServiceReference Materials Fireplace DimensionsConstitution Chimney Components 15-3/4 Parts Diagram NorthStar Fireplace DiagramBeginning Manufacturing Date Service PartsConstitution FP Ending Manufacturing DateSL1 Description Comments Serial Number DateThis page intentionally left blank Warranty Policy Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHearth & Home Technologies Limited Warranty Cont’d Contact Information Do not Discard this Manual

C-40 specifications

Hearth and Home Technologies (HHT) has long been known for its commitment to innovation and quality in the heating and home comfort industry. One of their standout offerings is the C-40, a versatile and efficient gas fireplace that embodies the brand’s dedication to modern aesthetics and advanced technology. This fireplace is designed to not only provide warmth but also enhance the ambiance of any living space.

The C-40 features a sleek, contemporary design that can seamlessly fit into various interior styles. Its clean lines and minimalist frame allow it to serve as a stylish focal point in a room, while offering the functionality and performance that homeowners expect from a high-quality gas fireplace. The unit is available in various configurations, including built-in and wall-mounted options, allowing for flexibility in installation and design.

One of the most notable features of the C-40 is its impressive heat output. With the ability to deliver efficient and evenly distributed warmth, this gas fireplace can effectively heat spaces of various sizes, making it an excellent choice for both small and large rooms. The adjustable flame height feature further enhances the user experience, allowing homeowners to customize their heating preference and create the perfect atmosphere for any occasion.

The C-40 is equipped with cutting-edge technologies, including electronic ignition and a remote control system, making it convenient and easy to use. The electronic ignition ensures quick and reliable startup, while the remote control allows for effortless temperature and flame adjustment from anywhere in the room. This added convenience is a significant benefit for those who value comfort and ease of operation.

Additionally, the C-40 incorporates advanced safety features, such as an automatic shut-off and a secure glass front, providing peace of mind for families. The glass front not only enhances safety but also serves to display the mesmerizing flames beautifully, allowing everyone to enjoy its warmth and glow.

In summary, Hearth and Home Technologies’ C-40 is a prime example of combining stylish design with modern technology and efficiency. Its exceptional heat output, customizable features, and advanced safety measures make it a standout choice for homeowners looking to enhance their living spaces with a dependable gas fireplace. Whether for cozy family gatherings or quiet evenings at home, the C-40 offers both aesthetic appeal and functional excellence, ensuring it remains a popular choice in contemporary home design.
Top Page Image Contents