Hearth and Home Technologies 31ST-ACC, 31M-ACC-MBK Wood Stove Series ACC Negative Pressure

Page 6

3100 Wood Stove Series (ACC)

R

C. Negative Pressure

Draft is the pressure difference needed to vent appliances successfully. Considerations for successful draft include:

Preventing negative pressure

Location of appliance and chimney

Negative pressure results from the imbalance of air avail- able for the stove to operate properly. Causes for this imbal- ance include:

Exhaust fans (kitchen, bath) etc.)

Range hoods

Combustion air requirements for furnaces, water heaters and other combustion appliances

Clothes dryers

Location of return-air vents to furnace or air condi- tioning

Imbalances of HVAC air handling system

Upper level air leaks

To minimize the affects of negative air pressure the following must be considered:

Install the outside air kit. Install the intake on the side of the house towards prevailing winds during the heating season.

Ensure adequate outdoor air is supplied for combus- tion appliances and exhaust equipment.

Ensure furnace and air conditioning return vents are not located in the immediate vicinity of the appli- ance,

Avoid installing the appliance near doors, walkways or small isolated spaces.

Recessed lighting should be of “sealed can” design; attic hatches weather stripped or sealed; and attic mounted duckwork and air handler joints and seams taped or sealed.

Recessed lighting

Attic hatch opening

Duct leaks

WARNING

Asphyxiation Risk.

Negative pressure can cause spillage of com- bustion fumes, soot and carbon monoxide.

Appliance needs to draft properly for safety.

 

 

 

Recommended Location:

 

 

 

Recommended Location:

• Above peak

 

 

 

 

Above peak

• Inside heated space

 

 

 

 

 

 

 

Marginal Location:

 

 

 

Marginal Location:

Wind loading possible

 

 

 

• Below peak

 

 

 

Location NOT recommended:

 

 

 

 

 

Not the highest point of the roof

 

 

 

 

 

Wind loading possible

 

 

 

 

 

 

 

 

 

 

Location NOT recommended:

 

 

 

 

 

Too close to tree

 

 

Recommended:

 

 

Below adjacent structure

 

 

• Insulated exterior chase

 

Lower roof line

 

 

in cooler climates

 

Avoid outside wall

 

Windward

 

 

 

 

 

 

 

 

 

 

 

Leeward

 

Recommended:

 

Multi-level Roofs

 

NOT recommended:

 

 

 

 

 

Outside Air Intake

 

 

 

Outside Air Intake

 

on windward side

 

 

 

on leeward side

Figure 6.1

Page

7033-277F

September 1, 2008

Image 6
Contents 7033-277F Step Top Uni-Body Model Millennium ModelHot glass will cause burns September 1Serial No Model Name Wood Stove Series ACC007 Mfg. Date 7033-277F September 1Table of Contents Listing and Code Approvals Appliance Certification BTU & Efficiency SpecificationsGlass Specifications Mobile Home ApprovedFire Safety Getting StartedWood Stove Series ACC Negative Pressure 7033-277F September 1Tools And Supplies Needed Wood Stove Series ACC Flue Draft ConsiderationsVenting Systems Inspect Appliance & Components and Pre-Use Check ListWood Stove Series ACC Typical Stove Systems Masonry ChimneyDimensions and Clearances Appliance DimensionsMillennium Model 11/16 in mm 11/16 in mm 89mm Back of Stove to Glass10-/8 in mm 21-1/8 in 7mm 7033-277F September 1 Wood Stove Series ACC Clearances to Combustibles UL and ULC Double Wall PipeHearth Protection Requirements Installation31004Wood Stove Series ACC Millennium ModelWood Stove Series ACC Step-Top Uni-Body Model Wood Stove Series ACC Outside Air Kit Installation Items Needed for Installation not suppliedFire Risk Asphyxiation Risk Wood Stove Series ACC Blower Optional Shock RiskVenting Components Chimney Systems Chimney ConnectorChimney Requirements ThimbleInstructions ComponentsAir Clearances Solid Pack Chimney with Metal Supports as a ThimbleInstalling Chimney Components Solid Pack Chimney with Metal Supports as a Thimble Cont’dChimney Height / Rise and Run Pitched Roof Wood Stove Series ACC Chimney Termination RequirementsRule Flat RoofMobile Home Installation Appliance Set Up Begin installing the ARS SystemInstalling Pedestal Assembly Finishing the ARS InstallationInstalling Leg Kit Corners. FigureWood Stove Series ACC Door Handle Assembly Adjusting The Blower Speed ControlWood Selection & Storage Operating InstructionsOver-Firing Your Appliance Wood Selection & Storage Cont’d Burning ProcessAutomatic Combustion Control ACC Air ControlsBurn Rates and Operating Efficiency Wood Stove Series ACC Building a Fire Wood Stove Series ACC Correct Baffle & Blanket Placement Incorrect PositionsWood Stove Series ACC Blower Operating Instructions Frequently Asked Questions Opacity SmokeInitial cold start-up and all Burn Settings Snap Disc LocationCreosote Chimney Cleaning General MaintenanceAsh Removal System ARS Operating and Cleaning Maintaining & Servicing Your ApplianceWhen cleaning glass Glass Cleaning Frequency As desiredCleaning Plated Surfaces Disposal of AshesWood Stove Series ACC Glass Replacement To your authorized dealer Wood Stove Series ACC Firebrick ReplacementAppliance without firebrick Brick Size QtyWood Stove Series ACC Baffle Removal Snap Disc Replacement Snap Disc LocationWood Stove Series ACC Tube Channel Assembly Replacement Removing Tube Channel AssemblyReplacing Tube Channel Assembly Troubleshooting Start Fire Problems Possible Cause SolutionReference Materials Exploded view#33 Baffle Board 2 w x 13-3/4 h, each #29 Ceramic Blanket 19 w x 13-3/4 h, 1/2 thickStep-Top Uni-Body Model Flue Collar can’t replace in the fieldWood Stove Series ACC Service Parts & Accessories Blower AssemblyItem # Service Parts Item # Service Parts Wood Stove Series ACC Service And Maintenance Log Date of Service Performed By Description of ServiceWood Stove Series ACC Homeowner’s Notes CONDITIONS, Exclusions & Limitation of Liability September 1 7033-277F Contact Information