Hearth and Home Technologies 31M-ACC-MBK, 31ST-ACC owner manual Installing Leg Kit, Corners. Figure

Page 23

R

3100 Wood Stove Series (ACC)

B. Leg Kit and Ash Removal Installation (ARS) for Step Top Uni-Body

NOTE: The Ash Removal System, must be installed first before installing the legs.

Installing Leg Kit

1.	Remove leg mounting brackets packaged inside firebox.
2.	Attach the 2 bottom screws of the mounting brackets to
	the bottom of the stove with 1/4”-20 Phillips head screws.
	These screws are located in the component pack .
	Leave the bottom 2 screws loose so you can slide the ash
	pan assembly bottom slots over the screw heads. This al-
	lows the weight of the ash pan to rest on the screws while
	you are attaching the top 2 screws. Once the ash pan is
	attached, tighten all screws. Figure 23.2.
3.	Loosely assemble bolts into the corner of the mounting

Lay stove flat on its back on protective padding or pallet

Leg Brackets

Ash Drawer

Insert 2 bottom screws loosely

	brackets for leg attachment. Figure 23.1.
4.	Slide legs onto mounting brackets and tighten. Make sure
	the legs are up against the bracket. There are leveling
	bolts in 2 legs. These leveling legs should be in opposite
	corners. Figure 23.1.
5.	Carefully stand stove up and place in desired location.
	Do NOT tilt up on the cast iron legs, it could damage the
	legs.
6.	Use leveling bolts on legs to stabilize and level stove.

Finishing the ARS Installation

1.Follow steps 1 through 3 on page 22. See also Figure 22.2.

Leg Mounting Brackets are

packaged inside firebox.

Leveling Legs at

opposite corners

Figure 23.1

Figure 23.2

CAUTION

Do NOT tilt the unit on the cast iron legs.

•Tilting could lead to property damage.

•Lift the unit upright and place it into position on the floor protector.

September 1, 2008

7033-277F

Page 23

Image 23

Contents September 1 Step Top Uni-Body Model Millennium ModelHot glass will cause burns 7033-277FMfg. Date 7033-277F September 1 Wood Stove Series ACC007 Serial No Model NameTable of Contents Mobile Home Approved Appliance Certification BTU & Efficiency SpecificationsGlass Specifications Listing and Code ApprovalsGetting Started Fire Safety7033-277F September 1 Wood Stove Series ACC Negative PressureInspect Appliance & Components and Pre-Use Check List Wood Stove Series ACC Flue Draft ConsiderationsVenting Systems Tools And Supplies NeededMasonry Chimney Wood Stove Series ACC Typical Stove SystemsMillennium Model Dimensions and ClearancesAppliance Dimensions 10-/8 in mm 21-1/8 in 7mm 7033-277F September 1 11/16 in mm11/16 in mm 89mm Back of Stove to Glass Double Wall Pipe Wood Stove Series ACC Clearances to Combustibles UL and ULCMillennium Model Installation31004Wood Stove Series ACC Hearth Protection RequirementsWood Stove Series ACC Step-Top Uni-Body Model Fire Risk Asphyxiation Risk Wood Stove Series ACC Outside Air Kit InstallationItems Needed for Installation not supplied Shock Risk Wood Stove Series ACC Blower OptionalThimble Chimney ConnectorChimney Requirements Venting Components Chimney SystemsSolid Pack Chimney with Metal Supports as a Thimble ComponentsAir Clearances InstructionsChimney Height / Rise and Run Installing Chimney ComponentsSolid Pack Chimney with Metal Supports as a Thimble Cont’d Flat Roof Wood Stove Series ACC Chimney Termination RequirementsRule Pitched RoofMobile Home Installation Begin installing the ARS System Appliance Set UpFinishing the ARS Installation Installing Pedestal AssemblyCorners. Figure Installing Leg KitAdjusting The Blower Speed Control Wood Stove Series ACC Door Handle AssemblyBurning Process Operating InstructionsOver-Firing Your Appliance Wood Selection & Storage Cont’d Wood Selection & StorageAir Controls Automatic Combustion Control ACCBurn Rates and Operating Efficiency Wood Stove Series ACC Building a Fire Incorrect Positions Wood Stove Series ACC Correct Baffle & Blanket PlacementSnap Disc Location Frequently Asked Questions Opacity SmokeInitial cold start-up and all Burn Settings Wood Stove Series ACC Blower Operating InstructionsMaintaining & Servicing Your Appliance General MaintenanceAsh Removal System ARS Operating and Cleaning Creosote Chimney CleaningDisposal of Ashes Glass Cleaning Frequency As desiredCleaning Plated Surfaces When cleaning glassWood Stove Series ACC Glass Replacement Brick Size Qty Wood Stove Series ACC Firebrick ReplacementAppliance without firebrick To your authorized dealerSnap Disc Location Wood Stove Series ACC Baffle Removal Snap Disc ReplacementReplacing Tube Channel Assembly Wood Stove Series ACC Tube Channel Assembly ReplacementRemoving Tube Channel Assembly Start Fire Problems Possible Cause Solution TroubleshootingExploded view Reference Materials#29 Ceramic Blanket 19 w x 13-3/4 h, 1/2 thick #33 Baffle Board 2 w x 13-3/4 h, eachFlue Collar can’t replace in the field Step-Top Uni-Body ModelBlower Assembly Wood Stove Series ACC Service Parts & AccessoriesItem # Service Parts Item # Service Parts Date of Service Performed By Description of Service Wood Stove Series ACC Service And Maintenance LogWood Stove Series ACC Homeowner’s Notes CONDITIONS, Exclusions & Limitation of Liability September 1 7033-277F Contact Information