LG Electronics LP121HEM-Y8 manual Condensate Drain kit, Drain Installation, Part No AYDR101

Page 29

4.Secure the grille to the sleeve by tightening the four screws to their corresponding holes in the grille.

5.Remove the wire handle after the installation is complete.

Note:

The stamped aluminum grille includes 6 screws, washers, nuts, and plastic grommets. The architectural grille includes 4 screws.

Condensate Drain kit

Part No: AYDR101

Receiving

Upon receipt of the product, inspect the shipping carton for signs of visible damage. Report any damage or shortage to the carrier and note it on the delivery receipt. The product must be stored in its original shipping carton in a dry, secure place prior to its installation and use.

Installation

The installation and servicing of the equipment referred to in this booklet should be performed by qualified, experienced technicians.

Figure 41 – Components of Drain Kits

Description

Condensate water will drain from the chassis into the sleeve during normal heat pump operation. This can also occur during times of high humidity when in cooling operation. Install either the outdoor or indoor drain kit components to control the condensate water where normal drainage from the wall sleeve is not possible or undesirable. See Figure 35 for all components of the drain kit.

WARNING

Hazardous Voltage!

Disconnect all electric power, including remote disconnects before servicing. Follow proper lockout/ tagout procedures to ensure the power can not be inadvertently energized. Failure to disconnect power before servicing could result in death or serious injury.

Important Note:

The unit OFF switch does not disconnect all electrical power to this unit.

DRAIN FITTING

 

BLANK-OFF

 

BLANK-OFF

PLATE B

 

PLATE C

 

PLATE C

GASKETS A

1/2" DRAIN FITTING

 

 

 

MTG. SCREWS

 

 

 

 

 

 

 

 

MTG. SCREWS

 

 

 

 

 

 

BLANK-OFF

GASKET E FOR

 

 

PLATE D

 

PLATE D

 

Drain Installation

Note:

The optional drain kit serves only as a link between the unit and field-supplied condensate drain system.

Installing the kit without connecting it to a drainage system will result in inadequate condensate removal, possible leakage and corrosion.

Algaecide: Some algaecide products may cause damage to the unit basepan and therefore should not be used. Contact your sales representative when considering the use of a commercial algaecide. See Figure 41 for components of the drain kit.

Copyright ©2008 LG Electronics. Inc. All right reserved.

- 29 -

Only for training and service purposes

LGE Internal Use Only

 

Image 29
Contents SVC Manual LGE Internal Use Only SpecificationSleeve and the Rear Grille Features and BenefitsOutdoor Air Temperature Switchover Door Switch/Occupancy SensorTemperature limits Quick Heater RecoveryOperation Electric Heating Model Control LocationsVentilation Cooling only ModelAdditional Controls Temperature LimitingRemoving the Front Grille Additional ControlsREMOTE/LOCAL Control Molex Housing SpecEnergy Saver Front Desk ControlFront Grille Disassembly InstructionsMechanical Parts Control BOX Electric Heater Electric Heater Model only AIR Handling PartsAxial FAN Cross Flow FANShroud Electrical PartsOutdoor Motor Compressor6 P.C.B Power CordCondenser Refrigeration CycleEvaporator Capillary TubeLGE Internal Use Only Pulling Vacuum HOW to Install the Unit InstallationDimension of air conditioner Dimension of sleeve assembly optionalGeneral Wall Sleeve InstallationWall Case Installation Data As shipped, the LG wall sleeve is ready for installation Installation of Wall Case in Wall OpeningPreparation of the Front Grille Preparation of the Wall Case for All Types of ConstructionLGE Internal Use Only Sub-Base Connected Unit Installation Electrical Requirements Electrical SafetyElectrical Data for 230/208V Model 208, 230, and 208/230 Volt UnitsInstallation Field Installed AccessoriesControl Panel Key Lock DescriptionHazardous Voltage Condensate Disposal Pump Kit InstallationPart No AYSB2101 Place the top cover assembly back into the unit Spraying Architectural Grille Architecture Grille Aluminum Single PackPart No AYDR101 Drain InstallationCondensate Drain kit Outdoor Drain Kit Installation Outdoor Drain Kit InstallationChecklist Indoor Drain Kit InstallationLeveling Legs Part No AYLL101Leveling Leg Assembly Installation on Wall Sleeve Leveling Leg AssemblyJunction Box Kit Installation and Wiring Procedure Hard Wire KitPart No AYAGALA01 Use Copper Conductors OnlyVolt Units 208/230 Volt UnitsPart No AYRE110 Remote Escutcheon KitPart No AYSB1101 230/208V 20A AYSB2101 230/208V 30A SubbaseTo each installation instruction for that accessory After wiring is complete, mount covers a and F toSkirting Hole Location Right Cover Assembly Subbase with provided screws. FigureOutside Dimensions Troubleshooting GuidePiping System 066mm 406mm 505mmTroubleshooting Guide Fails to Start Complaint Cause Remedy 208/230V 187V 253V Room AIR Conditioner Voltage LimitsComplaint Cause Remedy Th2 Thermistor for Evaporator pipe temperature Piping DiagramsTh3 Thermistor for outdoor Air temperature Th4 Thermistor for Condenser pipe Air temperatureCN-NN Schematic Diagram435300B Exploded ViewJanuary