White 1780 manual Cause, Foot control has been disconnected during

Page 50

______________

7. ERROR MESSAGES AND BEEP SOIJNDS

The help window LCD displays error messages when the machine is not operated correctly. When the following messages are displayed, correct the problems with the following sotutions.

Flashing display (with beep sounds)

Solution

Lower the presser foot lift

Possible

The start and stop button (or reverse stitch lever) was

cause

pressed when the presser foot lift is UP.

-DL

Pull down the buttonhole lever and push it to the bacl

S°‘“°untHftclicks,I

!1i

[ [

a -

>

J

*

Flashing

display

(no beep sound)

.

Possible

cause

Solution

••

Possible cause

Solution

Possible cause

The start and stop button was pressed when the butto hole stitch (Stitch No.1) is selected and with the button

hole lever UP.

Raise the buttonhole lever UP.

The start and stop button was pressed when the butto hole stitch (Stitch No.1) is NOT selected and with the buttonhole lever DOWN.

Move the bobbin winder shaft to the right.

The bobbin winder shaft returned to the left when wind the bobbin.

I Connect the foot control plugs correctly.

2 Do riot press the start and stop button when the machine is connected to the foot control.

1 The foot control has been disconnected during the

sewing.

2 The start and stop button was pressed when the foot control is connected to the sewing machine.

Set the correct stitch length

1 Stitch width is not set at 114fl when stretch stitches (Stitch No.11-20) are selected.

2 Stitch width is set to H4 when Stitch No.1 or stitch No.3-10 are selected.

Set the correct stitch width (except UOH)

Stitch width is set to when the stitch patterns select KIflT ctrinht tith (Stitnh Mn 2 nnr strniaht stretc

Page 49 Page 51
Image 50
Page 49 Page 51
Contents
‘Co ‘0 Canada DescargasParche 495 LCD de ayuda Accesorios estándarCostura en zigzag Prensatelas para sobrehilar Selector de anchura de puntadaJV C, F\ See Presser foot pressure adjustment lever SeeAdjuster See Needle threader See Presser foot holderIW’mw Standard accessories Stitch patterns UsesUnatelapesada Tipos de costuraDespIa Help window LCD functionsTipodepunto Fr,n +h m,-hir Mndn dc! ndI n I hse dl tabkr Mando de ajuste de los dientes Presser foot pressure adjustment leverGadada DrnZZ3GQ? Para una bobina pequeña Para una bobina grande Hci cIWinding bobbin El sImbolo aparecerá D. Para acelerar el bobinadoPage Pase el ThreadEnhebrar el hilo de Ia Page Enhebrar ThreadingPass SuperiorCómo se utiliza el enhebrador de aguja Use needle threaderPreparaciôn Pase el Press down the needle threader lever slowly So thatUse Para poder enhebrar Ia aguja, se debe introducirReemplazo del prensatelas Instalación del prensatelasHow to select a correct needle Seleccionar Ia aguja correctaFabric, thread and needle table PesadaPress Straight StitchPresser ReleaseInversion de puntada Reverse stitchPuntadas irregulares Ajuste de Ia tension del hiloPage Tension Adjusting thread tensionCostura Prensatelas Loot#9O/14 Parches Prensatelas para costuras invisibles Costuras incorrectasColoque un prensatelas para ojales Prensatelas para ojales Prensatelas para ojalesButtonhole foot La anchura de Ia puntada debe ser de 4 oWrong side by pulling the bobbin thread and tie El ojal se coseen at ordenaKnot Para evitar heridas, mantenga at abreojales ale su manoButton Unsuccessful Buttonhole sewingStitch balance Mal hechosPrensatelas para cremalleras Presser footStepsD-R Punto elástico Ifl CpoGuide Under the spring Plate on the shank Quilting guideAttach Pencil or tailors chalk and start to sewPreser Hem FootPress a Gathered fabric AssemblyRaise the needle to its highest position To gather Attach gatheredDarning Foot Feed Dog When You Finish DarningRaise Presser foot on After the quilt top is assembled By settingPiecing Is to piece the quilt top Pieces EvenCoser en Ia Orilla Stitch in the Dicth PorpiezaAcoichado libre Acoichado de CanalDesmontaje del alojamiento de Ia canilla IfIIirNo use detergentes, lejIa, gasolina, benc Dadas a continuación para desmontar el alTurn the handwheel and see if it moves smoothly Attaching the bobbin caseInstalaciôn del alojamiento de Ia canilla Lower the presser foot pressure rod Reemplazo de Ia bombillaFoot control has been disconnected during Pressed when the presser foot lift is UPCause Pull down the buttonhole lever and push it to the bacl# if Pressed Cases areSee AppearsNeedle or thread for Appearent PleaseNot threaded Too much presser foot pressureSotucaON EstãRevés 1780 45W/0.45Abombilladel2V/5WModelo Model