APC 40 130KVA user manual Load on Automatic

Page 43

Installation and User Manual

3.10.3List of Operating Status Conditions That May be Assigned to an SECI Output

Operating status	Description
conditions

GENERAL ALARM	PFC fault OR
	Inverter fault OR
	Bypass static switch fault OR
	Charger fault OR
	Thermal overload on AC bypass OR
	Normal AC input fuse blown OR
	ALIN board input fuse blown OR
	Q3BP and Q5N are closed simultaneously OR
	External Q3BP and external Q5N are closed simultaneously OR
	EPO activated OR
	Battery backup time ended, shift to wait mode OR
	Battery temperature fault > 45°C , charger shutdown OR
	Battery deep discharge OR
	Charger shutdown due to battery room temperature outside tolerances OR
	Abnormal presence of voltage on the output before closing the bypass static
	switch. (frequency converter) OR
	UPS in downgraded mode OR
	External CAN communication fault OR
	Internal CAN communication fault (GDEN, MIZNUS and CHAN) OR
	CAN cable physically cut OR
	CAN communication relay fault OR
	UPS personalization fault.

BATTERY FAULT	The battery will soon reach the end of its theoretical service life OR
	Battery must be checked (following a faulty battery test)

LOAD ON UPS	Inverter connected to the load and operating on normal AC input.
	Battery operations due to a BPI or battery test are signalled as operation on the
	normal AC input.

LOAD ON AUTOMATIC	The static switch on the AC bypass is closed.
BYPASS

LOAD ON BATTERY	Inverter connected to the load and operating on battery power.
POWER	Battery operations due to a battery test are not signalled.

LOW BATTERY WARNING	Battery has reached the low-battery warning level (voltage or time). The two
	thresholds may be user set.

OVERLOAD	One of the unit modules (rectifier, inverter or AC bypass) is overloaded (thermal or
	instantaneous).

86-174010-00 B00

Operation

3 — 9

Image 43

Contents MGE Galaxy Page Schneider Electric MGE GalaxyMGE Galaxy Important Safety InstructionsEnvironment This page left blank intentionally Contents Appendices MaintenanceWarranty and Product Registration Service Solutions Team Three Phase ProductsTables FiguresUPS Serial Number Safety of persons Safety RulesSpecial precautions Document Icons MGE Galaxy Symbol UsageDisplay Icons Introduction Setup and InstallationMaintenance Section DescriptionsViii Scope IntroductionGeneral Description UPS power rating KVA Dimensions H x W x D MGE Galaxy 5000 UPS System with Battery Single Line DiagramInside MGE Galaxy 5000 UPS Cabinet Inside the UPS Cabinet, Access to ConnectionsUPS Cabinet Bottom View Layout Power Connection TerminalsUser-Machine Interface Display User-Machine Interface DisplayDisplay Screens Display ScreensRelay Communication Card Relay Communication CardThis page left blank intentionally Introduction Location Setup and InstallationLayout of Cabinets Electrical SpecificationsSingle UPS With Common Normal and Bypass AC Inputs Connection of Power Cables in a Single UPSUPS Can // interconnections Exchange-current interconnectionsInterconnections with the external system bypass cabinet Parallel Configuration for Increased Capacity Four UPSsXMB08 XMB07 XMB06 11 Adding Communication Cards Adding Communication Cards12 Connection of Relay Communication Card Connection of the Relay Communications CardCommunications Card Connection Example Characteristics of the input contactsSingle UPS Routing the Control/Communications CablesGeneral-shutdown cable Can cables Parallel UPSExchange-current cables Shutting Down a Single UPS OperationRestarting a Single UPS Shutting Down a Parallel ConfigurationLoad is protected by the UPS Load is protected by the UPSs Restarting a Parallel ConfigurationSingle UPS Start Sequence on Normal AC Input Operation of Mimic-Panel LEDsSingle UPS Start Sequence on Bypass AC Input Operating Modes Load on Battery PowerFrequency Access to the Personalization FunctionsPersonalization Settings Operating Mode UPS PersonalizationDisplay Messages List Programmable Mode Standard ModeOperation of the Relay Communication Card Dry Contacts Load on Automatic AUTOMATIC-BYPASS Battery Temperature Fault This page left blank intentionally Life Cycle Monitoring LCM MaintenanceIdentification of Alarms Battery powerUPS Isolation Single UPS UPS IsolationLoad is no longer protected by the UPS Parallel UPS Configuration Without External Bypass Cabinet Shutdown and isolation of all the UPSs Parallel UPS Configuration With External Bypass CabinetReturn to Normal Single UPS Return to the Normal OperationUPS starts automatically LED 31 is on Parallel UPS Configuration Without External Bypass Cabinet UPS restarts and LED 31 is on Restart the UPS for which all switches are set to OFFReturn to Normal Parallel UPS With External Bypass Cabinet Training Center Servicing BatteriesHz Training Center This page left blank intentionally Appendices A1 Electrical CharacteristicsSelection of Protection Devices Limitation Input/Output Characteristics Load output Bypass AC inputInverter A2 Maximum Allowable Power for Parallel UPS Units A3 UPS Cabinet Major Internal Components MGE -GalaxyA4 Available Options A5 Environment Page Product Information MGE Galaxy Warranty and Product RegistrationWarranty Extension Warranty+ User InformationScheduling Field Service Engineer Support Technical Support and Product ServicesReturn Policy for Repair of Three Phase Products RGA MGE Galaxy AWG GlossaryIgbt VAC MGE Galaxy Use this form Reorder Form Scenic Avenue Costa Mesa, CAPage Page Contact Information