TROUBLE- |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| WARNING ICONG 001WARNING |
|
|
|
|
|
|
| |
SHOOTING |
|
|
|
|
|
|
|
|
|
|
| |
|
| Turn off and unplug heater and let cool before servicing. |
|
|
|
|
| |||||
Note: All troubleshooting items |
|
| Unless you need gas supply for testing, shut off manual |
|
|
|
| |||||
|
| shutoff valve before servicing. Only a qualified service |
|
|
|
| ||||||
are listed in order of operation. |
|
| person should service and repair heater and venting |
|
|
|
| |||||
|
|
| system. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| WARNING ICONG 001 CAUTION |
|
|
|
|
|
|
|
|
|
| Never use a wire, needle, or similar object to clean pilot. |
|
|
|
|
| ||||
|
|
| This can damage pilot. |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| |
|
| OBSERVED | POSSIBLE |
|
|
|
|
|
|
| ||
|
| PROBLEM | CAUSE | REMEDY |
|
|
| |||||
|
|
|
|
|
|
|
| |||||
|
| When ignitor button | 1. Incorrect spark gap. | 1. | Adjust spark gap to 1/16". |
| ||||||
|
| is pressed, there is no | 2. | Ignitor electrode posi- | 2. | Replace ignitor. |
|
|
| |||
|
| spark at pilot. |
| tioned wrong. |
|
|
|
|
|
|
| |
|
|
|
| 3. | Ignitor electrode broken. | 3. | Replace ignitor. |
|
|
| ||
|
|
|
| 4. | Ignitor electrode not con- | 4. | Reconnect ignitor cable. |
| ||||
|
|
|
|
| nected to ignitor cable. |
|
|
|
|
|
|
|
|
|
|
| 5. | Ignitor cable pinched or | 5. | Free ignitor cable if |
|
|
| ||
|
|
|
|
| wet. |
| pinched by any metal or |
| ||||
|
|
|
|
|
|
| tubing. Keep ignitor |
|
|
| ||
|
|
|
|
|
|
| cable dry. |
|
|
| ||
|
|
|
| 6. | Piezo ignitor nut is loose. | 6. | Tighten nut holding piezo |
| ||||
|
|
|
|
|
|
| ignitor to heater cabinet. |
| ||||
|
|
|
|
|
|
| Nut is located inside |
| ||||
|
|
|
|
|
|
| heater cabinet at top. |
|
|
| ||
|
|
|
| 7. | Broken or frayed ignitor | 7. | Replace ignitor cable. |
|
|
| ||
|
|
|
|
| cable. |
|
|
|
|
|
|
|
|
|
|
| 8. | Loose ignitor cable. | 8. | Reconnect ignitor cable. |
| ||||
|
|
|
| 9. | Bad piezo ignitor. | 9. | Replace piezo ignitor. |
|
|
| ||
|
|
|
|
|
|
|
|
| ||||
|
| When ignitor button | 1. Gas supply turned off or | 1. | Turn on gas supply or |
|
|
| ||||
|
| is pressed, there is |
| manual shutoff valve |
| open manual shutoff |
|
|
| |||
|
| spark at pilot but no |
| closed. |
| valve. |
|
|
| |||
|
| ignition. | 2. | Control knob not in | 2. | Turn control knob to |
|
|
| |||
|
|
|
|
| PILOT position. |
| PILOT position. |
|
|
| ||
|
|
|
| 3. | Control knob not | 3. | Press in control knob |
|
|
| ||
|
|
|
|
| pressed in while in |
| while in PILOT position. |
| ||||
|
|
|
|
| PILOT position. |
|
|
|
|
|
|
|
|
|
|
| 4. | Air in gas lines when | 4. | Continue holding down |
| ||||
|
|
|
|
| installed. |
| control knob. Repeat |
|
|
| ||
|
|
|
|
|
|
| igniting operation until |
| ||||
|
|
|
|
|
|
| air is removed. |
|
|
| ||
|
|
|
| 5. | Depleted gas supply. | 5. | Contact local propane |
|
|
| ||
|
|
|
|
|
|
| gas company. |
|
|
| ||
|
|
|
| 6. | Pilot is clogged. | 6. | Clean pilot (see Clean- |
| ||||
|
|
|
|
|
|
| ing and Maintenance, |
|
|
| ||
|
|
|
|
|
|
| page 26) or replace pilot |
| ||||
|
|
|
|
|
|
| assembly. |
|
|
| ||
|
|
|
| 7. | Gas regulator setting is | 7. | Replace control valve. |
|
|
| ||
|
|
|
|
| not correct. |
| Continued |
|
|
|
| |
|
|
|
|
|
|
| 27 |
| ||||
|
|
|
|
|
|
|
|
|
|
| ||
100791 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |