A.O. Smith SGE Week program setting the switch- on time, Bring the cursor to SU Confirm with

Page 67

gis

The display shows the menu for the week program, see the figure below. With the default setting, the program switches on and off every day at 00:00 and 23:59 hours respectively, the water temperature is 65°C and the pump is switched on (P).

	DAY TIME Tset
ON »SU		00:00 65ÉC P
OFF SU		23:59
ON	MO	00:00 65ÉC P

OFF	MO	23:59
ON	TU	00:00 65ÉC P
OFF	TU	23:59
ON	WE	00:00 65ÉC P
OFF	WE	23:59
ON	TH	00:00 65ÉC P
OFF	TH	23:59
ON	FR	00:00 65ÉC P
OFF	FR	23:59
ON	SA	00:00 65ÉC P
OFF SA		23:59
	INSERT

DELETE

START OPERATION

Example

As an example, we will set the switch-on time for Sunday to 08:15 hours, and the matching switch-off time to 12:45 hours. The water temperature will be set to 75 °C and the pump will run continuously.

The following settings are entered one by one via the menu: the switch-on time, the switch-off time, the desired water temperature, and the mode of the program-controlled pump.

11.7.1Week program: setting the switch- on time

1.Bring the cursor to SU

Confirm with .

ON	»SU 00:00
OFF	SU 23:59
Tset	65ÉC
PUMP	ON	SAVE

The day indicated by » flashes.

2.Use and to set the desired day. In the example this is SU (Sunday).

Confirm with .

ON	SU»00:00
OFF	SU 00:59
Tset	65ÉC
PUMP	ON	SAVE

The cursor moves to the hour digits, which flash.

3.Use and to set the hours. In the example, this is 08.

Confirm with .

The cursor moves to the minute digits, which flash.

ON	SU 08»00
OFF	SU 08:00
Tset	65ÉC
PUMP	ON	SAVE

Note

Because the switch-off time can never be earlier than the switch-on time, the switch-off time setting is automatically adjusted with the switch-on time.

4.Use and to set the minutes. In the example, this is 15.

Confirm with .

The cursor moves to the switch-off hour digits, which flash.

ON	SU 08:15
OFF	SU»08:15
Tset	65ÉC
PUMP	ON	SAVE

11.7.2Week program: setting the switch- off time

1.Use and to set the hours. In the example, this is 12.

Confirm with .

The cursor moves to the minute digits, which flash.

ON	SU 08:15
OFF	SU 12»15
Tset	65ÉC
PUMP	ON	SAVE

2.Use and to set the minutes. In the example, this is 45.

Confirm with .

The cursor moves to the desired water temperature.

ON	SU 08:15
OFF	SU 12:45
Tset»65ÉC
PUMP	ON	SAVE

11.7.3Week program: setting the water temperature

1.Use and to set the water temperature. In the example this is 75°C.

Confirm with .

The cursor moves to PUMP ON

ON SU 08:15

OFF SU 12:45

Tset 75ÉC

PUMP»ON SAVE

Instruction manual SGE

67

Image 67

Contents Installation User Your installer More information Read this manual carefullyTrademarks LiabilityGis Table of contents Status of the appliance Service programTroubleshooting Maintenance frequencyWarranty certificate Performing maintenanceAppendices Table of contents About the appliance IntroductionWhat to do if you smell gas Regulations Symbol Target group Target groups Maintenance Forms of notationIntroduction Chapter Target groups Description Overview of this documentGis Introduction General working principle of the appliance Working principle of the applianceTopics covered in this chapter Appliances heating cycle Other settings that govern the control behaviour areWorking principle of the appliance Protection for the appliance Introduction = time = Temperature 45 oC = Minimum tap water temperatureAppliance water temperature protection Gas valve Pressure switch Flame probe4 Fan Appliance water temperature protectionPressure switch Gas valveFlame probe Safety of the installationUnvented installation Vented installationPump of the solar heating system Fluid temperatureSafety of the solar heating system Expansion vessel Expansion valveConditions InstallationPackaging EnvironmentalAppliance maximum floor load Air humidity and ambient temperatureWater composition Working clearances See the table Technical specificationsDimensions of the appliance Appliance is supplied without accessories. CheckDime Description SGE Nsion Gas data General and electrical specificationsGas category 3+ G31 37 mbar Installation diagram Circulation pipe See C in the installation diagram 3.5 Installation diagramWater connections, Unvented Cold water side Hot water sideCondensation drainage Water connections, VentedThis section covers the following subjects Gas connectionAir supply and flue Introduction Requirements for flue gas discharge materialsTypes of appliances Concentric connections Following example illustrates how to use the table SpecificationsPractical example of concentric chimney flue Total length Bend Parallel connectionsSubject Description Appliance Diameter MaximumAppliance with parallel flue gas discharge material Practical example of parallel chimney flueElectrical connection Preparation Connecting the mains voltageConnecting communication cable to solar heating system Solar heating systemPreparation 11.211.2 Preparation Connecting the mains voltageConnecting continuous pump Isolating transformerConnecting extra head pump Connecting Q/T sensor Connecting a program-controlled pumpConnecting an extra on mode switch Tank on Connecting an extra error signal Alarm OUTConnecting pump station modulating pump Connecting the mains powerConnecting solar collector Connecting Q/T sensor Connecting tank sensorConnecting communication cable Connecting extra head pumpChecking the supply pressure and burner pressure Procedure to check pressures Gas data Adjusting the pressureFinish off 3.13.4 Finalising Finalising 13.4Conversion to a different gas category Orifice assemblyConversion to a different gas category Burner pressure regulator Blank plate Gas control connectorPage Conversion to a different gas category Filling Filling vented installations Filling the appliance Filling unvented installationsFilling Filling with glycol Flushing with waterGis Draining Position the cursor in front of OFF Draining unvented InstallationsDraining Activate the Menu withDraining solar heating system Draining glycol-filled system Draining vented installationsPosition the cursor in front of OFF Confirm OFF with Gis Meaning of icons Electronic controller ON/OFF switchControl panel ControlsPC connection Navigation buttonsControl panel Status of the appliance Operating modes Error conditions Service conditionOperating modes Q/T Sensor warning Service conditionError conditions Collector temperature warningStarting the appliance Appliances heating cycle Open 3.5 Installation diagram the manual gas valveStarting and running Starting the applianceIcon is activated Message PRE Purge appears Starting and runningIcon is activated Message Ignition appears Electrically isolating the appliance Shut the appliance down for a brief period OFF modeShutting down Shutting the appliance down for a long periodShutting down Notational convention for menu-related instructions Switching on the on modeSet the water temperature via Main menuChanging the appliances standard week program Setting water temperature during on modeWeek program Starting and stopping the week programBring the cursor to SU Confirm with Week program setting the switch- on timeWeek program setting the switch- off time Week program setting the water temperatureScroll with to Start Operation Confirm with Week program setting the program- controlled pumpAdding times to a week program Confirm with Display shown in the figure will appearTo delete a period, proceed as follows Confirm with Or use to cancelDeleting times from a week program Extra periodSetting the program-controlled pump Setting the switch-on timeSetting the switch-off time Setting the water temperatureAdjustable settings SettingsSetting menu language Setting day and timeScroll with to Specifications Confirm with Displaying appliance specifications SGEConfirm the minute setting with Table shows the correct settingsAppliance Default Range Service programSetting the hysteresis Displaying the error historySwitching legionella prevention on and off Switching the pump on or offSetting the service interval Setting legionella preventionSetting the solar limit temperature Solar heating system configurationSetting the drain-back tank Setting the heating fluid type in the solar heating systemSetting the central heating configuration Setting the QT sensor yes/noReading the energy contribution of the solar heating system Distinction is made between TroubleshootingGeneral errors Displayed errorsStart the appliance up 9 Starting and running Troubleshooting table for general errorsSymptom Cause Solution Remark Gas smell Display is offInsufficient or absent Symptom Cause Solution Remark Water leakageExplosive ignition Hot water supplySymptom Cause Solution Remark Troubleshooting table for displayed errors Displayed errors S13 blocking error Code + Description Cause Solution RemarkS11 blocking error S12 blocking errorF01 blocking error Code + Description Cause Solution Remark S18 blocking errorF02 lock out error Closing Code + Description Cause Solution Remark F03 lock out errorFails to work correctly Engineer Pressure switch not Maintenance 15.2 Preparation for maintenance. If there isArea Code + Description Cause Solution Remark F04 lock out errorF05 lock out error No gasSafety relay Engineer Code + Description Cause Solution Remark F06 lock out errorF07 lock out error F08 lock out errorF11 blocking error Code + Description Cause Solution Remark F10 lock out errorSelected appliance Code + Description Cause Solution Remark C02 lock out errorC03 blocking error C04 blocking errorE04 lock-out error Code + Description Cause Solution Remark E01 blocking errorTemperature E03 lock-out errorDisplayed warnings Standard setting is 500 burning hours Maintenance frequencyBest maintenance frequency can be determined Maintenance, based on the number of burning hoursMaintenance frequency Introduction Preparation for maintenance Performing maintenanceWait until the fan has stopped. The icon is then dimmed Performing maintenance Following steps must be carried out on the water side Water-side maintenance IntroductionDescaling and cleaning the tank Checking the anodesClean the orifices Cleaning condensation water dischargeGas-side maintenance Introduction Clean the burnersCollector warranty Conditions for Installation and use Warranty certificate16.1 General warranty 16.2 Tank warrantyWarranty certificate Heating system AppendicesThis appendix contains Menu structure of the main menu 17.2 Menu structureAppendices Menu structure101 Electrical diagram Electrical diagram for the applianceTemperature sensor T1 top Extra on mode switchExtra error signal connection Controller 0/I switchElectrical diagram, solar heating system Solar system electrical diagram legend 106 Example Period Week program cardPeriod Tset Pump108 109 IndexIndex 0308