Allstar Products Group MVP-SQ owner manual Installation of 2 Wire Safe Finish Photosystem

Page 13

13

 

CONTROL AND AUXILIARY EQUIPMENT

 

 

by moving approximately 45 feet back from the garage

erase any previously learned signal (Step 1).

door, then press the appropriate transmitter button that has

•If the distance is inadequate check the battery and

been programmed for that door. The red LED light will

illuminate on the front face of the transmitter. This is your

replace if necessary.

indication that a signal has been generated and sent out by

•If the distance is inadequate check the position of the

the transmitter (provided a valid programming sequence

power head unit antenna (see above).

has been done with the transmitter). Operation at this

 

distance should be reliable. However, environmental

•To maximize the operating distance move the

conditions and the location of the transmitter and receiver

transmitter to different locations in the car until a

antenna will affect distance.

 

 

satisfactory distance is achieved. Vanity mirrors on

•If the opener doesn’t activate check if the power head unit

sun visors will affect performance.

has been programmed to accept the transmitter signal. The

If the HomeLink® transmitter does not activate the

red LED on the rear panel of the power head unit will blink

operator or distance is inadequate, verify proper

two times rapidly if it has accepted a valid transmitter

operation using the transmitter packed with your

signal. If the LED light does not blink reprogram the MVP

opener. Contact your HomeLink® system provider

power head unit to accept the transmitter signal by

for help with configuring the HomeLink® transmitter

following the previous instructions “Programming the

and to resolve distance problems when using the

MVP Receiver Power Head Unit” making sure you

HomeLink® system.

 

 

 

 

INSTALLATION OF 2 WIRE SAFE FINISH PHOTOSYSTEM

STEP 1: Mark the position of the SAFE

FINISH™ Photosystem as follows: Mark a line on the left and right door jamb (close to the door track) FOUR (4) inches AND SIX (6) inches above the floor. The top mark is the maximum height and the bottom line is the minimum height that the photosystem

accessory can 104382 be placed.

STEP 2:

Mount the Photosystem "L" Brackets as follows:

A. Remove

the four mounting brackets from the package. Temporarily place the "U" shaped brackets, one around the receiver (unit with window and red LED) and one around the transmitter. NOTE: It is easier to slip the photosystem units in from the side of the bracket than forcing them in from the front of the bracket.

B.Your photosystem assembly is provided with a universal bracket set. Using either the transmitter or receiver (window up towards the ceiling), hold the "L" bracket and the "U" bracket set together while moving them in between the limit marks on the door jamb. Continue to move the photosystem assembly within the limit marks until it clears the door hardware. See Illustration, left. Check to ensure the window on the front of the photosystem unit is within the limit marks on the door jamb.

C.Place a mark in the center of the lag screw elongated mounting hole. Measure its position and place a similar mark on the opposite door jamb. The brackets may be temporarily mounted to the jamb with a 1" flat head nail (provided) using the small hole above the slot. Using two 5/16" X 1-1/2” lag screws (provided), permanently mount the "L" bracket to both door jambs.

STEP 3: Connect the Photosystem as follows: A.Remove the transmitter and receiver from their "U" mounting brackets.

Refer to Page 22 for various wiring options for the Safe Finish™ Photosystem. Steps B and C, below, describe the wiring for Series Connection with Receiver First, as illustrated on Page 19.

B.Run a wire pair (not supplied) around the garage door jamb between the transmitter and receiver "L" mounting brackets. NOTE: Leave about 12” of extra wire at each end. Use a minimum 22 gauge solid "trace" wire for interconnect.

C.Run a wire pair (20 or 22 gage solid wire) from the receiver position (unit with "LED" light in the front, may be either side of the door) back to the rear bulkhead of the garage door opener. NOTE: Leave about 12” of extra wire at the receiver end and about 24” of extra wire at the opener end.

D.Strip approximately 5/16” from each wire end at the photosystem units and at the opener.

E.Using two (2) wire nuts (supplied), connect the wire ends at the SAFE FINISH™ Photosystem transmitter to the pigtail wire ends coming out of the transmitter unit. Although not required, it is recommended to connect the trace wire ends together and the unmarked wire ends together.

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Residential Vehicular Garage Door Operator Tools Required for Installation Product FeaturesComponent Identification Assembly InstructionsPackaged separately Locate the Outer Trolley half packagedDoor Type Identification Important Installation Instructions Mounting the Front Installing the OpenerStraps in the slots closest to the front. Mounting may Using the PushReturn to the Tee Rail/Front Mounting Forward and thenAlternate Strut Connecting Bracket Cut to Fit Installing the OperatorOr Instructions Set the outer trolley to re-engage, seeInstall Installation of the Super Station Installation of a Standard Wall Push ButtonControl and Auxiliary Equipment RED LED will turn on Next, while continuing to First, press Hold the + button.Hole the + button, press and hold the button LED starts to blink Immediately releaseEnable button on the Super Station Light will serve as a status indicator during Recode newPanel of the power head Button when the red LED lightInstallation of 2 Wire Safe Finish Photosystem Final Installation Moving Downward Alternate Action Operation Operation and Adjustment InstructionsUpward Movement Radio Operation Unavailable, use a stiff cardboard Improper AdjustmentTo Close on People or PROPERTY, Causing Accessory System could Enable a Garage DoorDamaged or Malfunctioning Photoelectric Serious Injury or DeathWiring Diagram Universal Wiring Capabilities. The Safe Troubleshooting GuideManufacturer’s Limited Warranty

MVP-SQ, MVP specifications

Allstar Products Group has established itself as a leading provider of innovative consumer products, with its MVP and MVP-SQ lines standing out in the market for their exceptional quality and functionality. These products have been meticulously engineered to meet the diverse needs of consumers while setting a new benchmark for performance.

The MVP line is renowned for its versatility and user-friendly design. It incorporates advanced technologies that enhance efficiency and effectiveness, making it ideal for both professional and casual use. One of the standout features of the MVP is its ergonomic design, ensuring comfort during extended use. This thoughtful design reduces strain and fatigue, allowing users to make the most out of their experience.

With a focus on durability, the MVP is crafted from high-quality materials. This ensures longevity, even in demanding conditions. Additionally, the MVP showcases a range of innovative technologies, such as smart sensors and automatic adjustments that allow it to adapt to various tasks seamlessly. These features contribute to its reputation as a reliable tool for everyday tasks and specialized applications alike.

On the other hand, the MVP-SQ version elevates this concept further with added functionality tailored for specific use cases. This model integrates sophisticated technology that optimizes performance in specialized settings. The MVP-SQ is designed to tackle more complex challenges, making it perfect for professionals requiring precision and reliability.

Among the key characteristics of both models is their easy maintenance and clean-up. This is particularly appealing to consumers seeking convenience, as it allows for effortless upkeep after use. Furthermore, both MVP and MVP-SQ exhibit a sleek aesthetic, combining modern design with practicality, which is attractive for consumers who value style.

In conclusion, Allstar Products Group's MVP and MVP-SQ lines embody the perfect blend of technology, durability, and user-centric design. With their innovative features and attention to detail, these products are sure to meet the needs of an array of consumers, from casual users to industry professionals. Investing in either the MVP or MVP-SQ means opting for quality and performance that stand the test of time.
Top Page Image Contents