Allstar Products Group MVP-SQ Damaged or Malfunctioning Photoelectric, Serious Injury or Death

Page 17

17OPERATION AND ADJUSTMENT INSTRUCTIONS

1 1/2” BLOCK OF

104392 WOOD LAID FLAT (2”X4”)

Down force adjustments are

correct, the door will reverse within two seconds of contacting the object and travel to the Full Open position. If this does not occur, recheck the Limit Adjustments (Step 1, previous) and Sensitivity Adjustments (Step 2 & 3, previous.

W A R N I N G

FAILURE TO TEST

REVERSING SYSTEM

COULD RESULT IN DEATH

OR SERIOUS INJURY.

TEST THIS SYSTEM ONCE A MONTH BY FOLLOWING PROCEDURES OUTLINED

NOTE: Any time adjustments are made to Limits or Sensitivity, YOU MUST RETEST THE OPENER FOR THE REVERSING FEATURE AT FLOOR LEVEL AS OUTLINED ABOVE.

IN STEP 4 ON PAGE 16.

 

A DAMAGED OR MALFUNCTIONING PHOTOELECTRIC

 

ACCESSORY SYSTEM COULD ENABLE A GARAGE DOOR

 

TO CLOSE ON PEOPLE OR PROPERTY, CAUSING

 

SERIOUS INJURY OR DEATH.

W A R N I N G

PERFORM THIS TEST MONTHLY TO INSURE YOUR SAFE

FINISHPHOTOSYSTEM IS WORKING PROPERLY.

STEP 5: Testing the Safe Finish™ Photosystem — Start the door in the close travel direction and then

 

place an

104393

obstacle

 

approximately

 

6" high by 12"

 

wide in the

 

path of the

beam. The Red Pilot Light on the Safe Finish™ Photosystem should go out. The door

should stop and reverse to the full open position.

With the door fully open and at rest, place the obstacle in the path of the beam once again. Activate the Standard Wall Push Button. The opener should revert to and remain in the PUSH AND HOLD mode of operation for close travel. A radio control will not start the door downward with the beam blocked.

IF THE GARAGE DOOR TRAVELS MORE THAN ONE INCH IN A DOWNWARD PATH AFTER RELEASING THE BUTTON (WITH THE PHOTOBEAM BLOCKED), THE SAFE FINISH™ SYSTEM IS MALFUNCTIONING. CHECK THE ELECTRICAL CONNECTIONS AND ALIGNMENT OF THE PHOTOCELL MODULES.

STEP 6: Operating the Super Station (Deluxe Wall Pushbutton Station) Controls — The Super Station replaces standard a doorbell-type push button to allow you to integrate fully with all the convenience and security features built into your garage door opener.

1.Open Pushbutton — Green-backlighting, arrow pointing up. Used to start the door upward. This button will also stop and reverse a door that is closing. The button has no effect on a door that is opening. The function of this pushbutton is automatically disabled when the Security slide switch is set to the “ON” position and the door is fully closed.

104394

 

OPEN

STOP

Button

Button

CLOSE

Learn

Enable

Button

Button

 

 

Light

 

Button

Security

 

Disable

Security

Switch

Switch

Image 17
Contents Residential Vehicular Garage Door Operator Tools Required for Installation Product FeaturesComponent Identification Assembly InstructionsPackaged separately Locate the Outer Trolley half packagedDoor Type Identification Important Installation Instructions Mounting the Front Installing the OpenerStraps in the slots closest to the front. Mounting may Using the PushReturn to the Tee Rail/Front Mounting Forward and thenAlternate Strut Connecting Bracket Cut to Fit Installing the OperatorOr Instructions Set the outer trolley to re-engage, seeInstall Control and Auxiliary Equipment Installation of a Standard Wall Push ButtonInstallation of the Super Station RED LED will turn on Next, while continuing to First, press Hold the + button.Hole the + button, press and hold the button LED starts to blink Immediately releaseEnable button on the Super Station Light will serve as a status indicator during Recode newPanel of the power head Button when the red LED lightInstallation of 2 Wire Safe Finish Photosystem Final Installation Upward Movement Radio Operation Operation and Adjustment InstructionsMoving Downward Alternate Action Operation Unavailable, use a stiff cardboard Improper AdjustmentTo Close on People or PROPERTY, Causing Accessory System could Enable a Garage DoorDamaged or Malfunctioning Photoelectric Serious Injury or DeathWiring Diagram Universal Wiring Capabilities. The Safe Troubleshooting GuideManufacturer’s Limited Warranty

MVP-SQ, MVP specifications

Allstar Products Group has established itself as a leading provider of innovative consumer products, with its MVP and MVP-SQ lines standing out in the market for their exceptional quality and functionality. These products have been meticulously engineered to meet the diverse needs of consumers while setting a new benchmark for performance.

The MVP line is renowned for its versatility and user-friendly design. It incorporates advanced technologies that enhance efficiency and effectiveness, making it ideal for both professional and casual use. One of the standout features of the MVP is its ergonomic design, ensuring comfort during extended use. This thoughtful design reduces strain and fatigue, allowing users to make the most out of their experience.

With a focus on durability, the MVP is crafted from high-quality materials. This ensures longevity, even in demanding conditions. Additionally, the MVP showcases a range of innovative technologies, such as smart sensors and automatic adjustments that allow it to adapt to various tasks seamlessly. These features contribute to its reputation as a reliable tool for everyday tasks and specialized applications alike.

On the other hand, the MVP-SQ version elevates this concept further with added functionality tailored for specific use cases. This model integrates sophisticated technology that optimizes performance in specialized settings. The MVP-SQ is designed to tackle more complex challenges, making it perfect for professionals requiring precision and reliability.

Among the key characteristics of both models is their easy maintenance and clean-up. This is particularly appealing to consumers seeking convenience, as it allows for effortless upkeep after use. Furthermore, both MVP and MVP-SQ exhibit a sleek aesthetic, combining modern design with practicality, which is attractive for consumers who value style.

In conclusion, Allstar Products Group's MVP and MVP-SQ lines embody the perfect blend of technology, durability, and user-centric design. With their innovative features and attention to detail, these products are sure to meet the needs of an array of consumers, from casual users to industry professionals. Investing in either the MVP or MVP-SQ means opting for quality and performance that stand the test of time.