Allstar Products Group MVP-SQ owner manual Install

Page 9

9

INSTALLING THE OPENER

STEP 9: Consult the label on the rear panel of the Opener to determine its proper working voltage. Normally it will be marked for 115V, 60 cycle operation. (If it is an export model designed for 220V, 50 cycle operation, the label will clearly indicate this.) The Opener must be plugged into a properly grounded receptacle within 3 FT of the Power Unit. A GFI Type receptacle is recommended. Do not use 2-prong adapters and do not use extension cords for anything more than temporary hook-up and testing purposes. Receptacle wiring should be No. 14 or heavier, and must be in compliance with local building and electrical codes.

If local codes require permanent wiring, a GFI type circuit breaker is recommended to protect the line. Remove the Strain Relief Bushing and withdraw the Line Cord from the rear of the Power Unit to expose the three insulated connectors. Cut the wire at the rubber jacket of the Line Cord and wire in permanently, employing proper wiring practices. Discard Strain Relief. It is not used with permanent wiring.

WARNING

DISCONNECT POWER

AT FUSE BOX AND

OPENER BEFORE

WIRING PERMANENTLY

TO PREVENT

ELECTROCUTION.

Step 10: Install

104380

 

a Rough Service lamp bulb (75 Watt maximum) firmly in the light socket. Light bulbs in Door Openers are subject to vibration during normal operation which may shorten their life spans.

Rough Service bulbs, available at most hardware stores, are recommended. Fit Light Diffuser tabs into the panel slots as shown.

106428

WARNING

IMPROPER WIRING

COULD CAUSE

ELECTROCUTION OR

DAMAGE TO

CIRCUITRY. FOLLOW

LOCAL BUILDING AND

ELECTRICAL CODES.

DOWN

LIMIT CAM

STEP 11: On most models, the Limit Cams are installed at the factory. If the Limit Cams have not been installed, or it is necessary to move a Limit Cam to a different link, fasten them to the chain as shown at right in the approximate positions as illustrated below. Position the Switch Actuators as shown below.

FASTENING

LIMIT CAM TO

CHAIN

UP LIMIT

CAM

104381

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Residential Vehicular Garage Door Operator Tools Required for Installation Product FeaturesComponent Identification Assembly InstructionsPackaged separately Locate the Outer Trolley half packagedDoor Type Identification Important Installation Instructions Mounting the Front Installing the OpenerStraps in the slots closest to the front. Mounting may Using the PushReturn to the Tee Rail/Front Mounting Forward and thenAlternate Strut Connecting Bracket Cut to Fit Installing the OperatorOr Instructions Set the outer trolley to re-engage, seeInstall Installation of a Standard Wall Push Button Installation of the Super StationControl and Auxiliary Equipment RED LED will turn on Next, while continuing to First, press Hold the + button.Hole the + button, press and hold the button LED starts to blink Immediately releaseEnable button on the Super Station Light will serve as a status indicator during Recode newPanel of the power head Button when the red LED lightInstallation of 2 Wire Safe Finish Photosystem Final Installation Operation and Adjustment Instructions Moving Downward Alternate Action OperationUpward Movement Radio Operation Unavailable, use a stiff cardboard Improper AdjustmentTo Close on People or PROPERTY, Causing Accessory System could Enable a Garage DoorDamaged or Malfunctioning Photoelectric Serious Injury or DeathWiring Diagram Universal Wiring Capabilities. The Safe Troubleshooting GuideManufacturer’s Limited Warranty

MVP-SQ, MVP specifications

Allstar Products Group has established itself as a leading provider of innovative consumer products, with its MVP and MVP-SQ lines standing out in the market for their exceptional quality and functionality. These products have been meticulously engineered to meet the diverse needs of consumers while setting a new benchmark for performance.

The MVP line is renowned for its versatility and user-friendly design. It incorporates advanced technologies that enhance efficiency and effectiveness, making it ideal for both professional and casual use. One of the standout features of the MVP is its ergonomic design, ensuring comfort during extended use. This thoughtful design reduces strain and fatigue, allowing users to make the most out of their experience.

With a focus on durability, the MVP is crafted from high-quality materials. This ensures longevity, even in demanding conditions. Additionally, the MVP showcases a range of innovative technologies, such as smart sensors and automatic adjustments that allow it to adapt to various tasks seamlessly. These features contribute to its reputation as a reliable tool for everyday tasks and specialized applications alike.

On the other hand, the MVP-SQ version elevates this concept further with added functionality tailored for specific use cases. This model integrates sophisticated technology that optimizes performance in specialized settings. The MVP-SQ is designed to tackle more complex challenges, making it perfect for professionals requiring precision and reliability.

Among the key characteristics of both models is their easy maintenance and clean-up. This is particularly appealing to consumers seeking convenience, as it allows for effortless upkeep after use. Furthermore, both MVP and MVP-SQ exhibit a sleek aesthetic, combining modern design with practicality, which is attractive for consumers who value style.

In conclusion, Allstar Products Group's MVP and MVP-SQ lines embody the perfect blend of technology, durability, and user-centric design. With their innovative features and attention to detail, these products are sure to meet the needs of an array of consumers, from casual users to industry professionals. Investing in either the MVP or MVP-SQ means opting for quality and performance that stand the test of time.
Top Page Image Contents