Allstar Products Group MVP-SQ Pushbutton Station. The button is located inside a Code

Page 12

CONTROL AND AUXILIARY EQUIPMENT

12

Programming the MVP Radio Receiver in

Adding

WARNING

the Power Head Unit

 

Transmitters

Your opener will “learn” up to eight code transmissions

If additional

 

from preprogrammed transmitters. Locate the “Learn

transmitters are

TO PREVENT THE RISK

Enable” Button on the Super Station (Deluxe Wall

desired just match

OF PERSONAL INJURY,

Pushbutton Station). The button is located inside a

the code in the

DAMAGE TO DOOR OR

small hole on the front of the super station. You will

new transmitter to

PROPERTY, ONLY

need a pointed object to activate the button (such as a

the code in the

OPERATE DOOR

paper clip straightened out). Locate the red LED

existing

CONTROLS WHEN DOOR

indicator on the rear panel of the operator power head

transmitter. If

IS IN CLEAR VIEW. KEEP

unit (see illustration). The red LED light on the rear

you forget the

REMOTE CONTROL AWAY

panel of the power head unit and the operator work

existing code just

FROM CHILDREN IN A

light will serve as a status indicator during the

recode new and

SECURE AREA.

programming sequence.

 

existing products

 

SUPER STATION STEP 1: Press and hold the Learn

to a new code and

 

erase and reprogram your door operator. Any number

Enable button on the Super Station

of transmitters may be used to operate your door

for approximately five seconds. The

operator as long as one button of each transmitter is

 

red LED light on the rear

Learn

programmed with the same code learned by the door

panel of the power head

Enable

operator.

 

unit (and the work light)

 

Button

Installing the Transmitter

 

will illuminate and then

 

The transmitter is supplied with a metal clip which may

turn off. IMMEDIATELY release

be used to attach the unit to a sun visor. If the clip is

the button when the red LED light

used, slide it into the recess provided on

(and the work light) turn off. This

the back of the transmitter case

action will erase any previous signal

until the snaps on the case

that was learned by the control board and prepare it to

fit around the clip. If

 

learn your transmitter signal. At this time have your

 

the transmitter is

 

transmitter ready to transmit.

 

installed in a pocket in

STEP 2: Press and quickly release the Learn Enable

your car, follow all the

button on the Super Station. The red LED light on the

manufacturer’s

 

 

rear panel of the power

instructions. Improper

RED LED

head unit (and the work

installation may cause

 

LIGHT

light) will illuminate and

intermittent transmitter operation which can result in

GREEN LED

remain on, the control

unexpected door operations.

LIGHT

board is now ready to learn

Battery Replacement

 

the signal from your

The MVP Quik-Code transmitter is provided with two

 

transmitter. Within a

factory installed 3-volt batteries which should be replaced

POINT ANTENNA

twenty second time frame,

after two years of normal use. The transmitter code is

STRAIGHT DOWN

press the button on your

retained in permanent memory and will not be lost during

transmitter while pointing the transmitter at the power

battery replacement. To replace the batteries, remove the

head unit. The red LED light on the rear panel of the

back of the case using quarter or your thumb. Carefully slip

power head unit (and the work light) will then turn off.

the batteries out of the holders and replace with fresh

This is your indicator the control board has received

CR2032 3-volt batteries. The “+” on the batteries must

and accepted the signal from the transmitter. If the red

point away from the circuit board. Replace the back of the

LED light on the rear panel of the power head unit (and

cover and resume normal use.

the work light) remain on for more than 5 seconds this

Radio Operational Check - Note: Before performing the

indicates a code is already stored in the receiver.

radio operational check complete installation of the

Repeat Step 1 above to erase the code in the receiver.

Safe Finish™ Photosystem on page 13 and review the

Recheck the antenna wire on the power head unit, for

Installation Check List and Important Safety

proper operation the antenna wire should be POINTED

Instructions on pages 14 and 15.

STRAIGHT DOWN toward the floor (see illustration)

After programming your transmitter and the MVP receiver

for most situations.

 

power head unit, check the operation of your radio controls

HomeLink® is a registered trade mark of Johnson Controls, Inc.

This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Residential Vehicular Garage Door Operator Product Features Tools Required for InstallationAssembly Instructions Component IdentificationPackaged separately Locate the Outer Trolley half packagedDoor Type Identification Important Installation Instructions Installing the Opener Mounting the FrontUsing the Push Straps in the slots closest to the front. Mounting mayReturn to the Tee Rail/Front Mounting Forward and thenInstalling the Operator Alternate Strut Connecting Bracket Cut to FitOr Instructions Set the outer trolley to re-engage, seeInstall Installation of a Standard Wall Push Button Installation of the Super StationControl and Auxiliary Equipment First, press Hold the + button. RED LED will turn on Next, while continuing toHole the + button, press and hold the button LED starts to blink Immediately releaseLight will serve as a status indicator during Recode new Enable button on the Super StationPanel of the power head Button when the red LED lightInstallation of 2 Wire Safe Finish Photosystem Final Installation Operation and Adjustment Instructions Moving Downward Alternate Action OperationUpward Movement Radio Operation Improper Adjustment Unavailable, use a stiff cardboardAccessory System could Enable a Garage Door To Close on People or PROPERTY, CausingDamaged or Malfunctioning Photoelectric Serious Injury or DeathWiring Diagram Troubleshooting Guide Universal Wiring Capabilities. The SafeManufacturer’s Limited Warranty

MVP-SQ, MVP specifications

Allstar Products Group has established itself as a leading provider of innovative consumer products, with its MVP and MVP-SQ lines standing out in the market for their exceptional quality and functionality. These products have been meticulously engineered to meet the diverse needs of consumers while setting a new benchmark for performance.

The MVP line is renowned for its versatility and user-friendly design. It incorporates advanced technologies that enhance efficiency and effectiveness, making it ideal for both professional and casual use. One of the standout features of the MVP is its ergonomic design, ensuring comfort during extended use. This thoughtful design reduces strain and fatigue, allowing users to make the most out of their experience.

With a focus on durability, the MVP is crafted from high-quality materials. This ensures longevity, even in demanding conditions. Additionally, the MVP showcases a range of innovative technologies, such as smart sensors and automatic adjustments that allow it to adapt to various tasks seamlessly. These features contribute to its reputation as a reliable tool for everyday tasks and specialized applications alike.

On the other hand, the MVP-SQ version elevates this concept further with added functionality tailored for specific use cases. This model integrates sophisticated technology that optimizes performance in specialized settings. The MVP-SQ is designed to tackle more complex challenges, making it perfect for professionals requiring precision and reliability.

Among the key characteristics of both models is their easy maintenance and clean-up. This is particularly appealing to consumers seeking convenience, as it allows for effortless upkeep after use. Furthermore, both MVP and MVP-SQ exhibit a sleek aesthetic, combining modern design with practicality, which is attractive for consumers who value style.

In conclusion, Allstar Products Group's MVP and MVP-SQ lines embody the perfect blend of technology, durability, and user-centric design. With their innovative features and attention to detail, these products are sure to meet the needs of an array of consumers, from casual users to industry professionals. Investing in either the MVP or MVP-SQ means opting for quality and performance that stand the test of time.
Top Page Image Contents