Allstar Products Group MVP-SQ owner manual Component Identification, Assembly Instructions

Page 3

3

 

COMPONENT IDENTIFICATION

 

DRIVE

DOOR ARM

DOOR ARM ROD

 

CHAIN

 

TUBE ASSEMBLY

 

 

 

 

 

 

MASTER

 

OPENER HEAD UNIT

LINKS

 

 

 

TEE RAIL

 

 

 

CHAIN

RADIO

 

 

GUARD

 

DOOR MOUNTING

TRANSMITTER

CONTROL WIRE

 

BRACKET

 

 

SPOOL

 

 

 

 

 

SUPER STATION

 

RELEASE

DELUXE WALL

OPENER

PUSH BUTTON

ROPE

 

HARDWARE

AND KNOB

 

BAG

 

! WARNI NG

 

 

 

PUSHBUTTON

Child can be pinned under automatic garage

 

“WARNING”

Test door opener monthly:

 

 

door. Death or serious injury can result.

 

 

Never let child walk or run under moving door.

RUBBER BUMPER

 

Never let child use door opener controls.

 

Always keep moving door in sight.

 

 

If person is pinned, push control button or use

 

 

emergency release.

 

LABEL

 

WALL FRONT TROLLEY MOUNTING

IDLER OUTER BRACKET HALF

SAFE FINISH

PHOTOSYSTEM

PHOTOSYSTEM

HARDWARE

104363

NOTE: The Tee

 

Rail/Chain Assembly is

 

packaged separately

from the Power Unit. The Inner Trolley half, Front Idler Sprocket, Chain, and Limit Cams are assembled on the Tee Rail at the factory.

Follow the steps outlined below to complete assembly prior to installation. Refer to the component identification illustrations on the previous page.

STEP 1: Protect the Power Unit cover from scratching during assembly by placing it on cardboard. Remove the two 5/16"-18 washered nuts and save them for later use.

STEP 2: Position the Tee Rail/Chain Assembly box near the Power Unit. Open the box and locate the Installation Hardware Packet.

STEP 3: Locate the Outer Trolley half (packaged

ASSEMBLY INSTRUCTIONS

with the Power Unit) and slide it onto the Tee Rail/ Chain Assembly with the arrow on the Trolley pointing toward the door (Front Idler).

STEP 4: Using a 1/2" wrench, loosen the outer nut on the Chain Tension Bracket until it is at the end of the threaded rod. Remove and discard the small "S" hook used to keep the chain tight during shipping.

STEP 5: Loop the chain around the Idler and Drive Sprocket on top of the Power Unit and then position the Tee Rail on the studs. Secure with the two nuts removed in Step 1.

Slightly tension the Chain by tightening the outer nut on the Chain Tension Bracket. Remove and discard the tape at each end of the Tee Rail Assembly. After double-checking the Chain's alignment with the Drive Sprocket and Front Idler Wheel, use the inner and outer adjusting nuts on the Chain Tension Bracket to adjust the chain to the proper tension, making sure the chain does not twist. When correctly adjusted, the

Chain should show no droop and be approximately 1/2" above the base of the Tee Rail.

104365

NOTE: If the chain is too loose or too tight, improper operation and/or excessive sprocket noise may result.

Image 3
Contents Residential Vehicular Garage Door Operator Tools Required for Installation Product FeaturesLocate the Outer Trolley half packaged Assembly InstructionsComponent Identification Packaged separatelyDoor Type Identification Important Installation Instructions Mounting the Front Installing the OpenerForward and then Using the PushStraps in the slots closest to the front. Mounting may Return to the Tee Rail/Front MountingSet the outer trolley to re-engage, see Installing the OperatorAlternate Strut Connecting Bracket Cut to Fit Or InstructionsInstall Installation of a Standard Wall Push Button Installation of the Super StationControl and Auxiliary Equipment LED starts to blink Immediately release First, press Hold the + button.RED LED will turn on Next, while continuing to Hole the + button, press and hold the buttonButton when the red LED light Light will serve as a status indicator during Recode newEnable button on the Super Station Panel of the power headInstallation of 2 Wire Safe Finish Photosystem Final Installation Operation and Adjustment Instructions Moving Downward Alternate Action OperationUpward Movement Radio Operation Unavailable, use a stiff cardboard Improper AdjustmentSerious Injury or Death Accessory System could Enable a Garage DoorTo Close on People or PROPERTY, Causing Damaged or Malfunctioning PhotoelectricWiring Diagram Universal Wiring Capabilities. The Safe Troubleshooting GuideManufacturer’s Limited Warranty

MVP-SQ, MVP specifications

Allstar Products Group has established itself as a leading provider of innovative consumer products, with its MVP and MVP-SQ lines standing out in the market for their exceptional quality and functionality. These products have been meticulously engineered to meet the diverse needs of consumers while setting a new benchmark for performance.

The MVP line is renowned for its versatility and user-friendly design. It incorporates advanced technologies that enhance efficiency and effectiveness, making it ideal for both professional and casual use. One of the standout features of the MVP is its ergonomic design, ensuring comfort during extended use. This thoughtful design reduces strain and fatigue, allowing users to make the most out of their experience.

With a focus on durability, the MVP is crafted from high-quality materials. This ensures longevity, even in demanding conditions. Additionally, the MVP showcases a range of innovative technologies, such as smart sensors and automatic adjustments that allow it to adapt to various tasks seamlessly. These features contribute to its reputation as a reliable tool for everyday tasks and specialized applications alike.

On the other hand, the MVP-SQ version elevates this concept further with added functionality tailored for specific use cases. This model integrates sophisticated technology that optimizes performance in specialized settings. The MVP-SQ is designed to tackle more complex challenges, making it perfect for professionals requiring precision and reliability.

Among the key characteristics of both models is their easy maintenance and clean-up. This is particularly appealing to consumers seeking convenience, as it allows for effortless upkeep after use. Furthermore, both MVP and MVP-SQ exhibit a sleek aesthetic, combining modern design with practicality, which is attractive for consumers who value style.

In conclusion, Allstar Products Group's MVP and MVP-SQ lines embody the perfect blend of technology, durability, and user-centric design. With their innovative features and attention to detail, these products are sure to meet the needs of an array of consumers, from casual users to industry professionals. Investing in either the MVP or MVP-SQ means opting for quality and performance that stand the test of time.