Allstar Products Group MVP Control and Auxiliary Equipment, Installation of the Super Station

Page 10

CONTROL AND AUXILIARY EQUIPMENT

10

INSTALLATION OF A STANDARD WALL PUSH BUTTON

If desired, a standard wall push button may be installed and connected to your operator. A standard wall push button is not included in your hardware package, it can be purchased from your professional installing dealer or a door bell button [without light] can be substituted.

The operating parameters for the standard wall push button are outlined on a page that follows to see if that mode of operation is right for you. The Super Station is included with this operator and the manufacturer rec- ommends its installation as the Super Station will pro- vide full control over the garage door at all times.

STEP 1: After determining a suitable location, usually near the access door and at least 5 feet above the floor to prevent use by children, use the standard wall push button as a guide to mark the mounting holes. Drill holes for drywall anchors or screws. NOTE: Do not mount directly to masonry walls. Use backer board.

STEP 2: A length of 2-conductor, #22 gauge wire (or heavier) is required to connect the standard wall push button to the garage door operator. Strip approximately 2” of the wire jacket from one end and 1/2” of insulation from each wire. Carefully connect one wire to each of the two terminals. Carefully tuck the loose wires into the case and mount the unit using appropriate screws.

STEP 3: Run the wire from the standard wall pushbutton to the operator, supporting it at 18” intervals with suitable staples. Leave a sufficient length to make the necessary connections to the operator terminal strip.

WARNING

A CHILD OPERATING THE DOOR

CONTROLS RISKS INJURY — OR DEATH

—TO HIMSELF (HERSELF) AND OTHERS. DO NOT ALLOW CHILDREN TO OPERATE

ANY DOOR CONTROLS.

MOUNT THE PUSHBUTTON AT LEAST 5 FEET FROM THE FLOOR, OUT OF REACH OF CHILDREN.

WARNING: SOME LOCAL BUILDING CODES DO NOT ALLOW SURFACE WIRING. BE SAFE AND CHECK WITH YOUR LOCAL BUILDING INSPECTOR FIRST.

STEP 4: Ensure power is OFF to the operator or disconnect the power from the operator. Strip approximately 4” of jacket from the end of the wire and 1/2” insulation from each wire. Connect to terminals 0 and 1 as shown in the illustration below. Support the wire near the operator with wire ties.

Step 5: Install the Control Button Warning Label supplied with your opener near the standard wall push button (see illustration next page).

INSTALLATION OF THE SUPER STATION

The Super Station (Deluxe Wall Pushbutton Station) is a 7 function station designed to work with and maximize the functionality of your garage door opener. Connection to any other opener may damage the opener and/or the Super Station. Only connect one Super Station to each opener. Do not connect more than one Super Station to an Opener.

108387MOUNTING HOLES

BACK

STANDARD WALL

SUPER STATION

DELUXE WALL PUSH

PUSH BUTTON

BUTTON

STEP 1: After determining a suitable location, usually near the access door and at least 5 feet above the floor to prevent use by children, use the Super Station as a guide to mark the mounting holes. Drill holes for drywall anchors or screws. NOTE: Do not mount directly to masonry walls. Use backer board. The Super Station is also designed to be mounted directly to a standard single electrical box.

STEP 2: A length of 2-conductor, #22 gauge wire (or heavier) is required to connect the Super Station to the garage door opener. Strip approximately 6” of the wire jacket from one end and 1/2” of insulation from each wire. Carefully connect one wire to each of the two terminals indicated, noting which color is connected to which terminal. Tighten screws, being careful that no wires are allowed to touch any other terminal or any other conductive part of the circuit board. Do not overtighten the terminal screws.

STEP 3: Push the wire jacket into one of the two notches provided at the ends of the housing, allowing a maximum of 1/8” inch of the jacket inside the case (too much will make mounting difficult). Carefully tuck the loose wires into the case and mount the unit using the screws provided.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Residential Vehicular Garage Door Operator Product Features Tools Required for InstallationPackaged separately Assembly InstructionsComponent Identification Locate the Outer Trolley half packagedDoor Type Identification Important Installation Instructions Installing the Opener Mounting the FrontReturn to the Tee Rail/Front Mounting Using the PushStraps in the slots closest to the front. Mounting may Forward and thenOr Instructions Installing the OperatorAlternate Strut Connecting Bracket Cut to Fit Set the outer trolley to re-engage, seeInstall Installation of the Super Station Installation of a Standard Wall Push ButtonControl and Auxiliary Equipment Hole the + button, press and hold the button First, press Hold the + button.RED LED will turn on Next, while continuing to LED starts to blink Immediately releasePanel of the power head Light will serve as a status indicator during Recode newEnable button on the Super Station Button when the red LED lightInstallation of 2 Wire Safe Finish Photosystem Final Installation Moving Downward Alternate Action Operation Operation and Adjustment InstructionsUpward Movement Radio Operation Improper Adjustment Unavailable, use a stiff cardboardDamaged or Malfunctioning Photoelectric Accessory System could Enable a Garage DoorTo Close on People or PROPERTY, Causing Serious Injury or DeathWiring Diagram Troubleshooting Guide Universal Wiring Capabilities. The SafeManufacturer’s Limited Warranty

MVP-SQ, MVP specifications

Allstar Products Group has established itself as a leading provider of innovative consumer products, with its MVP and MVP-SQ lines standing out in the market for their exceptional quality and functionality. These products have been meticulously engineered to meet the diverse needs of consumers while setting a new benchmark for performance.

The MVP line is renowned for its versatility and user-friendly design. It incorporates advanced technologies that enhance efficiency and effectiveness, making it ideal for both professional and casual use. One of the standout features of the MVP is its ergonomic design, ensuring comfort during extended use. This thoughtful design reduces strain and fatigue, allowing users to make the most out of their experience.

With a focus on durability, the MVP is crafted from high-quality materials. This ensures longevity, even in demanding conditions. Additionally, the MVP showcases a range of innovative technologies, such as smart sensors and automatic adjustments that allow it to adapt to various tasks seamlessly. These features contribute to its reputation as a reliable tool for everyday tasks and specialized applications alike.

On the other hand, the MVP-SQ version elevates this concept further with added functionality tailored for specific use cases. This model integrates sophisticated technology that optimizes performance in specialized settings. The MVP-SQ is designed to tackle more complex challenges, making it perfect for professionals requiring precision and reliability.

Among the key characteristics of both models is their easy maintenance and clean-up. This is particularly appealing to consumers seeking convenience, as it allows for effortless upkeep after use. Furthermore, both MVP and MVP-SQ exhibit a sleek aesthetic, combining modern design with practicality, which is attractive for consumers who value style.

In conclusion, Allstar Products Group's MVP and MVP-SQ lines embody the perfect blend of technology, durability, and user-centric design. With their innovative features and attention to detail, these products are sure to meet the needs of an array of consumers, from casual users to industry professionals. Investing in either the MVP or MVP-SQ means opting for quality and performance that stand the test of time.
Top Page Image Contents