Allstar Products Group MVP-SQ owner manual Final Installation

Page 14

CONTROL AND AUXILIARY EQUIPMENT

F. Using two (2) wire nuts (supplied), connect the

B. Place the

wire ends at the SAFE FINISH™ Photosystem

transmitter and

receiver to the pigtail wire ends coming out of the

receiver units

receiver unit. Although not required, it is

into their

recommended to connect the trace wire ends together

respective "U"

and the unmarked wire ends together.

brackets. See

 

Illustration, at

104383

right.

C. Connect the

 

 

interconnect wire

 

pair to the garage

 

door opener

 

terminals marked

14

WARNING

AN AUTOMATIC GARAGE DOOR SYSTEM POSES A THREAT OF INJURY OR EVEN DEATH. INSTALL THE SAFE FINISH PHOTOSYSTEM NO HIGHER THAN 6” ABOVE THE GARAGE FLOOR TO REDUCE THE RISK TO SMALL CHILDREN.

STEP 4 : Final Installation

A.Attach the"U" brackets to the "L" brackets with a 1/4-20 carriage bolt, washer and hex nut (provided). Insert the bolt from the inside of the "U" bracket and hand tighten only at this time.

"1" & "4". Although not required, it is suggested that the "trace" be connected to Terminal 4. See Wiring Diagram, Page 19.

Tighten all mounting screws and bolts. Final alignment and the system test is covered on Page 17, Step 5 “E: Operation and Adjustment Instructions.

PRE-POWER ON-

INSTALLATION CHECKLIST

Before continuing with the operation and adjustment section, make sure that:

1.The front and rear mounts for the opener are sound and secure and the rail is positioned correctly above the high arc of the door, and that the opener is positioned over the door action centerline.

2.For sectional door and one piece door with tracks, the position of the door arm (with the door closed), is such that it’s connecting point on the trolley is 5” to 8” behind it’s connecting point on the door bracket. The door arm should never be perfectly vertical when the door in in the closed position.

3.The Manual Release Label and cord are secure to the Manual Release Lever. The handle is located 6 FT above floor level and requires no more than a 50 pound pull to activate. The trolley and the release mechanism are properly lubricated.

4.The standard wall push button or the Super Station (deluxe wall push button station) is in such a position and of such a height that it can only be actuated by an adult of average height. The Control Button Warning label is prominently displayed next to the push button or wall station.

5.All wiring is correct to codes or better. There is ground continuity form the supply. The ground prong on the power cord is intact.

6.All ropes have been removed from the door. The door moves freely without binding when raised or lowered manually. The door is correctly balanced and lubricated. All door hardware is secure and sound. The sensitivity has been adjusted to minimum force for the application.

7.The door reverses on obstructions to within 1.5" of the floor. The concrete or other surface beneath the closed door provided uniform contact.

8.The plastic envelope for this manual is attached to the wall near the push button or wall station and this manual is placed there for owner use and reference.

9.On door with extension type counterbalance springs, restraint cables have been placed through the springs.

10.There is Ground Fault Interruption (GFI) protection of the power line to the opener or in the receptacle.

11.On doors with adjustable bottom edges, edges have been locked after adjustment.

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Residential Vehicular Garage Door Operator Product Features Tools Required for InstallationPackaged separately Assembly InstructionsComponent Identification Locate the Outer Trolley half packagedDoor Type Identification Important Installation Instructions Installing the Opener Mounting the FrontReturn to the Tee Rail/Front Mounting Using the PushStraps in the slots closest to the front. Mounting may Forward and thenOr Instructions Installing the OperatorAlternate Strut Connecting Bracket Cut to Fit Set the outer trolley to re-engage, seeInstall Control and Auxiliary Equipment Installation of a Standard Wall Push ButtonInstallation of the Super Station Hole the + button, press and hold the button First, press Hold the + button.RED LED will turn on Next, while continuing to LED starts to blink Immediately releasePanel of the power head Light will serve as a status indicator during Recode newEnable button on the Super Station Button when the red LED lightInstallation of 2 Wire Safe Finish Photosystem Final Installation Upward Movement Radio Operation Operation and Adjustment InstructionsMoving Downward Alternate Action Operation Improper Adjustment Unavailable, use a stiff cardboardDamaged or Malfunctioning Photoelectric Accessory System could Enable a Garage DoorTo Close on People or PROPERTY, Causing Serious Injury or DeathWiring Diagram Troubleshooting Guide Universal Wiring Capabilities. The SafeManufacturer’s Limited Warranty

MVP-SQ, MVP specifications

Allstar Products Group has established itself as a leading provider of innovative consumer products, with its MVP and MVP-SQ lines standing out in the market for their exceptional quality and functionality. These products have been meticulously engineered to meet the diverse needs of consumers while setting a new benchmark for performance.

The MVP line is renowned for its versatility and user-friendly design. It incorporates advanced technologies that enhance efficiency and effectiveness, making it ideal for both professional and casual use. One of the standout features of the MVP is its ergonomic design, ensuring comfort during extended use. This thoughtful design reduces strain and fatigue, allowing users to make the most out of their experience.

With a focus on durability, the MVP is crafted from high-quality materials. This ensures longevity, even in demanding conditions. Additionally, the MVP showcases a range of innovative technologies, such as smart sensors and automatic adjustments that allow it to adapt to various tasks seamlessly. These features contribute to its reputation as a reliable tool for everyday tasks and specialized applications alike.

On the other hand, the MVP-SQ version elevates this concept further with added functionality tailored for specific use cases. This model integrates sophisticated technology that optimizes performance in specialized settings. The MVP-SQ is designed to tackle more complex challenges, making it perfect for professionals requiring precision and reliability.

Among the key characteristics of both models is their easy maintenance and clean-up. This is particularly appealing to consumers seeking convenience, as it allows for effortless upkeep after use. Furthermore, both MVP and MVP-SQ exhibit a sleek aesthetic, combining modern design with practicality, which is attractive for consumers who value style.

In conclusion, Allstar Products Group's MVP and MVP-SQ lines embody the perfect blend of technology, durability, and user-centric design. With their innovative features and attention to detail, these products are sure to meet the needs of an array of consumers, from casual users to industry professionals. Investing in either the MVP or MVP-SQ means opting for quality and performance that stand the test of time.
Top Page Image Contents