Allstar Products Group 3500-P, J3500, 3000 Connect the standard wall Push Button provided to

Page 11

C:INSTALLING THE OPERATOR

STEP 7: Tie a double overhand knot in one end of the Emergency Release Rope and slip the other end through the red Release Handle, the Release Instruction Card, and the hole at the end of the Release Lever on the Trolley. Tie a second double overhand knot in the free end, adjusting the Rope so that the Red Handle is 6 FT above the floor. If the Rope must be cut, flame seal the cut end with a match or lighter.

NOTE: The Emergency Release Mechanism is engaged by pulling the Release Handle down and away from the door. This allows the Trolley Mechanism to separate, freeing the door from the Opener's transport mechanism. To re-engage, simply move the Emergency Release Mechanism Lever forward and then operate normally using the Push Button or Radio Control. The two parts of the Trolley Mechanism will automatically reconnect.

STEP 8: Connect the standard wall Push Button provided to

DOUBLE

Terminals 1 & 0 on the Opener's rear panel using a length of

OVERHAND

2-conductor, minimum 22 gauge wire. For mounting the standard

KNOT

Push Button, select a convenient location near an access door.

 

Mount at least 5 FT from the floor to prevent small children

 

from operating the door. Install the Caution Label supplied with

 

the Opener near this installation.

 

If you are installing an Allstar Deluxe Wall Push Button Station,

 

See Page 16 for the proper wiring procedure.

 

DOUBLE

OVERHAND

KNOT

RELEASE INSTRUCTION

CARD

 

FLOOR

104378

 

 

104379

 

 

 

KEEP PEOPLE AND OBJECTS OUT OF

 

DOOR OPENING WHEN USING

 

MANUAL DISCONNECT. AN OPEN OR

 

PARTIALLY OPEN DOOR MAY FALL

WARNING

UNCONTROLLABLY IF

 

DISCONNECTED FROM OPERATOR.

 

CONTACT A SERVICE PROFESSIONAL

 

TO CORRECT ANY DOOR PROBLEMS.

WARNING

WARNING

A CHILD OPERATING THE DOOR CONTROLS RISKS INJURY — OR DEATH — TO HIMSELF AND OTHERS. DO NOT ALLOW CHILDREN TO OPERATE ANY DOOR CONTROLS.

MOUNT THE PUSHBUTTON AT LEAST 5 FT FROM

THE FLOOR, OUT OF REACH OF CHILDREN.

IMPROPER DOOR OPERATION COULD CAUSE INJURY OR DEATH. CAUTION LABEL MUST BE MOUNTED ON WALL NEAR THE PUSHBUTTON. ALL WARNINGS AND INSTRUCTIONS ON THE LABEL SHOULD BE STRICTLY ADHERED TO.

! WARNING

Child can be pinned under automatic garage door. Death or serious injury can result.

Never let child walk or run under moving door.

Never let child use door opener controls.

Always keep moving door in sight.

If person is pinned, push control button or use emergency release.

Test door opener monthly:

Refer to your owner’s manual

Place one-inch object (or 2x4 laid flat) on floor. If door fails to reverse on contact, adjust opener.

Ifopener still failstoreversedoor, repair or replaceopener.

11

104350

 

Image 11
Contents Series Table of Contents Optional Features Product FeaturesTools Required Component IdentificationStep Assembly InstructionsAdjustment Important Installation To Reduce the Risk of Severe InjuryDo not Attempt Adjustment Installing the OperatorHigh ARC Rise High ARC Rise Horizontal Line Mounting the Front Bracket OneMounting straps in the slots closest to Front Mount Power Head to CeilingSectional Doors and One Piece Doors with Track One Piece Doors without Track Raise the openerDoor ARM Connection and Installation Mount at least 5 FT from the floor to prevent small children Connect the standard wall Push Button provided toFastening Limit CAM to Chain Connect the Photosystem as follows Auxiliary EquipmentPhotosystem Unit is Within the Limit Marks on the Door Jamb Final Alignment and Test Final InstallationInstallation of Radio Controls ONE SECOND, and then Begin Moving Upward Operating ParametersCheck with Your Local Building Inspector First If the Door is104390 Warni NG Operation and Adjustment InstructionsSecurity Switch is Garage Testing the All-Clear PhotosystemOperator Wiring Diagram Series Connection Receiver First Wiring Auxiliary EquipmentInstallation Checklist Probable Cause Troubleshooting GuideSymptom Probable CAUSE/SOLUTION SolutionAllstar Corporation Downingtown, PA