Chamberlain WD962KLD BNSTALLATiON Step, Outside Keylock Accessory Connections, Mounting If \1

BNSTALLATiON STEP 6

Insfall t_e Door Contro/J

Locate door control within sight of door, at a minimum height of 5 feet (1,5 m) where small children cannot reach, away from moving parts of door and door hardware.,

If installing into drywall, drill 5/32" holes and use the anchors provided. For pre-wired installations (as in new home construction), it may be mounted to a single gang box (Figure 2).,

1,Strip 7/t6" (11 ram) of insulation from one end of bell wire and connect to the two screw terminals on back of

the door control by color: white wire to 2 and white/red wire to the 1.,

2, Remove cover by gently prying at slot in top of the cover with a small flat head screwdriver, Fasten with 6ABx1-

1/4" setf4apping screws (drywall installation) or 6-32xl" machine screws (into gang box) as follows:

-install bottom screw, allowing 1/8" (3 mm) to protrude above walt surface,

•Position bottom of the door control on screw head and slide down to secure.. Adjust screw for snug fit.,

o Drill and install top screw with care to avoid cracking plastic housing., Do not overtighten.

• Insert top tabs and snap on cover•

3,,(For standard installation only) Run bell wire up wall and across ceiling to motor unit° Use insulated staples to secure wire in several places. Do not pierce wire with a staple, creating a short or open circuit,,

4.Strip 7/16" (11 mm) of insulation from end of bell wire, Connect bell wire to the quick-connect terminals as follows: white to white and white/red to red..

5, Position the antenna wire as shown,,

To preventpossibleSERIOUSIr_lJURYor DEATHfrom electrocution:

. DisconnectALLelectric andbattery power BEFORE performingANYserviceor maintenance,

. ConnectONLYto 24 VOLTlow voltagewires.,

To preventpossibleSERIOUSINJURYor DEATHfrom a cfosing garagedoor:

°Install the door controlwithin sight of garagedoor, out of reach of children at a minimum height of 5 feet (1.5 m), and away fromALL movingpads of door

. NEVERpermit childrento operateor playwith the door controf push buttons or remotecontrols.

-ActivatedoorONLYwhen it can beseendearly, is properly adjusted,andthere areno obstructions to door travel,

°ALWAYSkeepgaragedoor in sight until completelyclosed.. NEVERpermitanyoneto cross path of closing garagedoor.,

Outside Keylock Accessory Connections

To opener quick-connectterminals: white to white; white/ red to red.,

HARDWARE SI-tOWN ACTUAL SiZE

(standard installation)

_ !i!l!illli*iiliHil

Screw 6_32x1"
(p_'e-wired)	Drywall Anchors

Figure 1 Figure 2

6, Use tacks or staples to permanently attach entrapment	STANDARD WALL	MOUNT
	To Replace
warning label to wall near door control, and manual		PBE_WtRED 1NSTALLATION_
	tnserl Top lI_
release/safety reverse test label in a prominent location
on inside of garage door,.		Tabs First _,[
NOTE: DO NOT connect power and operate opener at
this time., The trolley will travel to the full open position but	Push Bar Cover	Switch
will not return to the close position until the sensor beam is
connected and properly aligned,		Push Bar Cover_	_	_,OFF
				Switch

_Top		Mounting
IF" \_1-			Door Controi Connections	To insert or release wi_o,
f - tJ]		,o,o
				1screwdriver tip
,_	_.,	Terminal		/
,,III		Screws	Strip wi_e 7tl 6" (t 1 ram)
Bet!lll_.,---__"_IIl Bottom
w_,. _		HMoOUnt,ng
(BACK VIEW)

i..................

17