Chamberlain WD962KD, WD962KLD Assembly Step t, Assemble the Rail and Install the Trolley

Page 8

ASSEMBLY STEP t

Assemble the Rail and Install the Trolley

To avoid installation difficulties, do not run the garage door opener until instructed to do so.

The front rail has a cut out "window" at the door end (see illustration). The hole above this window is larger on

the top of the rail than on the bottom.. A smaller hole

3-1/2" (8.9 cm) away is close to the rail edge. Rotate the back rail so it has a similar hole close to the opposite edge, about 4-3/4" (!2 cm) from the far end.

1.Remove the straight door arm and hanging bracket packaged inside the front rail and set aside for Installation Step 5 and 12_ NOTE: To prevent INJURY while unpacking the rail carefully remove the straight door arm stored within the rail section.,

2.Align the rail sections on a flat surface as shown and slide the tapered ends into the larger ones., Tabs along the side will lock into place.

To preventINJURYfrom pinching,keephands andfingers

I

awayfrom the jointswhileassemblingthe rail.

I

 

I

3.Place the motor unit on packing material to protect the cover, and rest the back end of the rail on top.. For convenience, put a support under the front end of the rail..

4.As a temporary stop, insert a screwdriver into the hole I0" (25 cm) from the front end of the rail, as shown..

5.Check to be sure there are 4 plastic wear pads inside the inner trolley.. If they became loose during shipping, check all packing material. Snap them back into position as shown..

6 Slide the trolley assembly along the rail from the back end to the screwdriver..

Trolley

KEEP LARGER

HOLE ON TOP

End

lack Rails

(TO MOTOR UNIT)

End

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Garage Door Opener For Residential Use OnlyAdjustment 28.30 AccessoriesService Warranty Safety Symbol and Signal Word ReviewPreparing your garage door Sectional DoorOne-Piece Door To preventpossibleSERIOUSINJURYor Death Tools neededPlanning Sectional Door InstallationsDoor Installation ONE-PIECEDOOR Installations ONE-PIECEDOOR with TrackCurved Door Assembly Hardware Installation HardwareAssembly Step t Assemble the Rail and Install the TrolleyAssembly Step Nut3Install the Belt and Atach the Belt Cap RetainerSeE the Tension INSTALLATllONReadandfollowall Installationwarningsand Instructions Installation Step t 0cmWall Header Bracket Installation Ceiling Header Bracket InstallationMNSTALLATBON Step Knstal# the Header BracketMHSTALLATION Step UHSTALLATaOH Step Position the OpenerONE-PIECEDOOR Without Track Top of the door should be level with the topIhstallatiion Step Hang the OpenerOutside Keylock Accessory Connections BNSTALLATiON StepUse tacks or staples to permanently attach entrapment Mounting If \1DONOTusebulbs largerthan Ioow ONLYuseA19 sizebulbs Install the Battery BackupUtNISTALLATilON Step Handle MNSTALLATl!OH StepAttach the Emergency Release Rope MNSTALLATmON Step t Elec*rical RequirementsInstall The Protector System Safety Sensors Important Information about Safety Reversing SensorInstalling the Brackets Garage door track installation preferredWall installation Figures 2 Floor installation FigureTroubleshooting the Safety Reversing Sensors Mounting and Wiring the Safety Reversing SensorsAligning the Safety Reversing Sensors Bnstallation Step t Fasten he Door BracketSectional Doors Wood DoorsONE-PIECE Doors GarageSectional Doors only UNSTALLATmN StepConnect Door Arm to Trolley Assemble the Door Arm Adjustment Step Doora,desiredlllAdjustment Step Se**ing the ForceTest the Safety Reversal System Test The Protector System s Safety SensorsTest Repeat the tesLAlwayskeepgaragedoorproperlybalanced Using Your Garage Door OpenerReadandfollowallwarningsand Instructions Light feature Lock featureAdditional feature when used with Button hand-heM remoteMaintenance Schedule Remote Control BatteryCare Of Your Opener Once a MonthBattery Backup Operating InstructionsOrange LED Green LEDMy lights will not turn off when door is open Having a Problern? TroubHeshootingMy remotes will not activate the door My motor unit hums brieflyDiagnostic Charf Possible RPM sensor failure. Unplug to resetSymptom LED is not lit on door control Symptom RPM Sensor = Short travel 6-815-20 cmTo Add or Reprogram a Hand.held Remote Control Erase All Codes From Motor Unit MemoryButton 315 MHzUsing the Learn Button Using the Motion Detecting Control 7o Add, Reprograrn or Cange a Keyless EnEry PINDescription Installation ParisKEY Part KEY Part Description Motor Unit Assembly PartsKEY Part NO. no Button Mini-Remote Control with SECURITY,I 77020BOutside Quick Release760CB 8808CB 8810CB 41A5281 Foot 3 m Rail ExtensionHotes Page Chamberlain Service is On Call OUR Large Service Organization Spans America

WD962KLD, WD962KD specifications

The Chamberlain WD962KD and WD962KLD are powerful garage door opener models designed to provide homeowners with advanced technology, convenience, and reliability. Both models come equipped with smart features that make them stand out in the market.

One of the primary features of the WD962KD and WD962KLD is the powerful 1.25 HP motor. This robust motor ensures that even the heaviest garage doors can be opened and closed smoothly without straining the system. The WD962KLD model, in particular, features a DC motor, which not only offers silent operation but also enhances energy efficiency.

Both garage door openers are equipped with Chamberlain's patented MAX Lift Power System. This innovative technology delivers optimal lifting force and steady performance, making the opening and closing cycle faster and more efficient. The models are compatible with various types of garage doors, including sectional, one-piece, and up-and-over doors, providing versatility to suit different homeowners' needs.

Security is a major concern for homeowners, and Chamberlain addresses this with its advanced security features. The WD962KD and WD962KLD come with the MYQ technology, allowing users to monitor and control their garage door from anywhere using their smartphones. The app notifies users about the door's status in real time, providing peace of mind.

Another essential characteristic is the built-in battery backup feature. This ensures that even during power outages, homeowners can still operate their garage doors without hassle. The WD962KLD model goes one step further with its integrated lighting system that illuminates the garage area, enhancing safety and visibility when entering or exiting.

Installation is made easy with the included Quick-Install bracket system, which simplifies the setup process. The smooth operation is further complemented by the silent operation chain drive, ensuring minimal noise during usage, which is perfect for homes that are attached to the garage.

Furthermore, both garage door openers come with remote controls featuring a range of up to 1500 feet, enabling users to open their garage door from a significant distance. The keypad entry system offers an added layer of convenience and security, allowing for keyless access.

In summary, the Chamberlain WD962KD and WD962KLD garage door openers combine advanced technologies and user-friendly features to deliver a premium experience. With robust motors, smart technology, enhanced security options, and easy installation, these models are an excellent choice for homeowners looking to upgrade their garage door systems.
Top Page Image Contents