Chamberlain WD962KD, WD962KLD owner manual 7o Add, Reprograrn or Cange a Keyless EnEry PIN

Page 38

7"o Add, Reprograrn or C_ange a Keyless EnEry PIN

NOTE: Your new Keyless Entry must be programmed to operate your garage door opener,

USING THE "LEARN" BUTTON

USING THE MOTION DETECTING CONTROL

1..Press and release the "learn" button on motor uniL The learn indicator light will glow steadily for 30 seconds..

NOTE: This method requires two people if the Keytess Entry is already mounted outside the garage,.

1..Enter a four digit personal identification number (PIN) of your choice on the keypad.. Then press and hold ENTER,.

2.Within 30 seconds, enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold the ENTER button.

3.Release the button when the motor

unit lights biink., it has learned the code If light bulbs are not installed, two clicks will be heard.,

To change an existing, known PIN

If the existing PIN is known, it may be changed by one person without using a ladder..

1..Press the four buttons for the present PIN, then press and hold the # button..

The opener light will blink twice. Release the # button

2..Press the new 4-digit PIN you have chosen, then press Enter.

The motor unit lights will blink once when the PIN has been learned..

Test by pressing the new PiN, then press Enter., The door should move,

To set a temporary PIN

You may authorize access by visitors or service people with a temporary 4-digit PIN. After a programmed number of hours or number of accesses, this temporary PIN expires

and will no longer open the door.. It can be used to close the door even after it has expired_ To set a temporary PIN:

1..Press the four buttons for your personal entry PIN (not

the last temporary PIN), then press and hold the =I= button..

The opener light will blink three times, Release the button..

2.While holding the ENTER button, press and hold the LIGHT button on the Motion Detecting Door Control.

3Continue holding the ENTER and LIGHT buttons while you press the push bar on the Motion Detecting Door Control (all three buttons

are held)..

4,, Release buttons when the motor unit lights blink_ It has learned the code.. If

light bulbs are not installed, two clicks will be heard,.

2o Press the temporary 4-digit PIN you have chosen, then press Enter,

The opener light will blink four times

3.,To set the number of hours this temporary PIN will work, press the number of hours (up to 255), then press :I:.

OR

3..To set the number of times this temporary PIN will work, press the number of times (up to 255), then press #..

The opener light will blink once when the temporary PIN has been learned

Test by pressing the four buttons for the temporary PIN, then press Enter. The door should move. If the temporary PiN was set to a certain number of openings, remember that the test has used up one opening, To clear the temporary password, repeat steps 1-3, setting the number of hours or times to 0 in step 3o

One Button Close: Opener can be closed by pressing onty the ENTER button if the one button close feature has been activated. This feature has been activated at the factory. To activate or deactivate this feature press and hold buttons 1 and 9 for 10 seconds. The keypad will blink twice when the one button close is active. The keypad will blink four times when one button close is deactivated.

38

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Garage Door Opener For Residential Use OnlyService Warranty Adjustment 28.30Accessories Safety Symbol and Signal Word ReviewOne-Piece Door To preventpossibleSERIOUSINJURYor Death Preparing your garage doorSectional Door Tools neededPlanning Sectional Door InstallationsDoor Installation ONE-PIECEDOOR Installations ONE-PIECEDOOR with TrackCurved Door Assembly Hardware Installation HardwareAssembly Step t Assemble the Rail and Install the TrolleyAssembly Step Nut3Install the Belt and Atach the Belt Cap RetainerSeE the Tension INSTALLATllONReadandfollowall Installationwarningsand Instructions Installation Step t 0cmMNSTALLATBON Step Wall Header Bracket InstallationCeiling Header Bracket Installation Knstal# the Header BracketMHSTALLATION Step ONE-PIECEDOOR Without Track UHSTALLATaOH StepPosition the Opener Top of the door should be level with the topIhstallatiion Step Hang the OpenerUse tacks or staples to permanently attach entrapment Outside Keylock Accessory ConnectionsBNSTALLATiON Step Mounting If \1DONOTusebulbs largerthan Ioow ONLYuseA19 sizebulbs Install the Battery BackupUtNISTALLATilON Step Handle MNSTALLATl!OH StepAttach the Emergency Release Rope MNSTALLATmON Step t Elec*rical RequirementsInstall The Protector System Safety Sensors Important Information about Safety Reversing SensorWall installation Figures 2 Installing the BracketsGarage door track installation preferred Floor installation FigureTroubleshooting the Safety Reversing Sensors Mounting and Wiring the Safety Reversing SensorsAligning the Safety Reversing Sensors Sectional Doors Bnstallation Step tFasten he Door Bracket Wood DoorsONE-PIECE Doors GarageSectional Doors only UNSTALLATmN StepConnect Door Arm to Trolley Assemble the Door Arm Adjustment Step Doora,desiredlllAdjustment Step Se**ing the ForceTest Test the Safety Reversal SystemTest The Protector System s Safety Sensors Repeat the tesLAlwayskeepgaragedoorproperlybalanced Using Your Garage Door OpenerReadandfollowallwarningsand Instructions Additional feature when used with Light featureLock feature Button hand-heM remoteCare Of Your Opener Maintenance ScheduleRemote Control Battery Once a MonthOrange LED Battery BackupOperating Instructions Green LEDMy remotes will not activate the door My lights will not turn off when door is openHaving a Problern? TroubHeshooting My motor unit hums brieflySymptom LED is not lit on door control Diagnostic CharfPossible RPM sensor failure. Unplug to reset Symptom RPM Sensor = Short travel 6-815-20 cmButton To Add or Reprogram a Hand.held Remote ControlErase All Codes From Motor Unit Memory 315 MHzUsing the Learn Button Using the Motion Detecting Control 7o Add, Reprograrn or Cange a Keyless EnEry PINDescription Installation ParisKEY Part KEY Part Description Motor Unit Assembly PartsKEY Part NO. no 760CB 8808CB 8810CB 41A5281 Button Mini-Remote Control with SECURITY,I77020BOutside Quick Release Foot 3 m Rail ExtensionHotes Page Chamberlain Service is On Call OUR Large Service Organization Spans America

WD962KLD, WD962KD specifications

The Chamberlain WD962KD and WD962KLD are powerful garage door opener models designed to provide homeowners with advanced technology, convenience, and reliability. Both models come equipped with smart features that make them stand out in the market.

One of the primary features of the WD962KD and WD962KLD is the powerful 1.25 HP motor. This robust motor ensures that even the heaviest garage doors can be opened and closed smoothly without straining the system. The WD962KLD model, in particular, features a DC motor, which not only offers silent operation but also enhances energy efficiency.

Both garage door openers are equipped with Chamberlain's patented MAX Lift Power System. This innovative technology delivers optimal lifting force and steady performance, making the opening and closing cycle faster and more efficient. The models are compatible with various types of garage doors, including sectional, one-piece, and up-and-over doors, providing versatility to suit different homeowners' needs.

Security is a major concern for homeowners, and Chamberlain addresses this with its advanced security features. The WD962KD and WD962KLD come with the MYQ technology, allowing users to monitor and control their garage door from anywhere using their smartphones. The app notifies users about the door's status in real time, providing peace of mind.

Another essential characteristic is the built-in battery backup feature. This ensures that even during power outages, homeowners can still operate their garage doors without hassle. The WD962KLD model goes one step further with its integrated lighting system that illuminates the garage area, enhancing safety and visibility when entering or exiting.

Installation is made easy with the included Quick-Install bracket system, which simplifies the setup process. The smooth operation is further complemented by the silent operation chain drive, ensuring minimal noise during usage, which is perfect for homes that are attached to the garage.

Furthermore, both garage door openers come with remote controls featuring a range of up to 1500 feet, enabling users to open their garage door from a significant distance. The keypad entry system offers an added layer of convenience and security, allowing for keyless access.

In summary, the Chamberlain WD962KD and WD962KLD garage door openers combine advanced technologies and user-friendly features to deliver a premium experience. With robust motors, smart technology, enhanced security options, and easy installation, these models are an excellent choice for homeowners looking to upgrade their garage door systems.
Top Page Image Contents