Chamberlain WD962KLD, WD962KD owner manual Assembly Step, Nut3

Page 9

ASSEMBLY STEP 2

Fasten the Rail to the Motor Unit

*Insert a 1/4"-20xl-3/4 bolt into the cover protection bolt hole on the back end of the rail as shown Tighten securely with a 1/4"-20 lock nut. Do not overtighten.

o Remove the two bolts from the top of the motor uniL

,Place the "U" bracket, fiat side down, on the motor unit and align the bracket holes with the bolt holes Fasten with the previously removed bolts.

°Align the rai! assembly with the top of the motor unit.. Slide the rail end onto the "U" bracket, all the way to the stops that protrude on the top and sides of the bracket,

HARDWARE SHOWN ACTUAL SIZE

Bolt I14"-20xl-3!4"

t/4"-20

To avoid sERIOus damageto garagedoor opener,use ONLY

those bets/fastenersmountedin the top of the opener..

Motor Unit

Belt Pulley

/

"U" Bracket

Boil

{ Cover

SLIDE RAiLTO STOPS

ONOF BRACKETTOP AND StDES

Loc_kNu!

ASSEMBLY STEP 3

install the Idler Pulley

oLay the belt beside the rail, as shown.. Grasp the end with the hooked trolley connector and pass approximately 12" (30 cm) of belt through the window,. Keep the ribbed side toward the rail, and allow it to hang until Assembly Step 5.

-Remove the tape from the idler pulley. The inside center should be pre-greased If dry, regrease to ensure proper operation,.

•Place the idler pulley into the window as shown..

•Insert the idler bolt from the top through the rail and pulley° Tighten with a 3/8" lock washer and nut underneath the rail until the lock washer is compressed

-Rotate the pulley to be sure it spins freely.

•Insert a 1/4"-20xl-3/4 bolt into the trolley stop hole in the front of the rail as shown. Tighten securely with a 1/4"-20 lock nut

Bolt

Trolley

_-- Inside Pulley

Grease Stop F_

Lock Washer _

Idler Pulley

_- Nut3,_" ,,,,,,_..

1

Y!

Conneclor

I_ Lock

Pulley 1 Nut

HARDWARE SHOWN ACTUAL SIZE

Idler Boll

Boll 114"-20xt-3/4"

Look Nut 1/4"-20

Nut 318"

Lock Washer 3.,'8"

Page 8 Page 10
Image 9
Page 8 Page 10
Contents For Residential Use Only Garage Door OpenerAccessories Adjustment 28.30Service Warranty Safety Symbol and Signal Word ReviewSectional Door Preparing your garage doorOne-Piece Door To preventpossibleSERIOUSINJURYor Death Tools neededSectional Door Installations Door InstallationPlanning ONE-PIECEDOOR with Track ONE-PIECEDOOR InstallationsCurved Door Installation Hardware Assembly HardwareAssemble the Rail and Install the Trolley Assembly Step tNut3 Assembly StepRetainer Install the Belt and Atach the Belt CapINSTALLATllON Readandfollowall Installationwarningsand InstructionsSeE the Tension 0cm Installation Step tCeiling Header Bracket Installation Wall Header Bracket InstallationMNSTALLATBON Step Knstal# the Header BracketMHSTALLATION Step Position the Opener UHSTALLATaOH StepONE-PIECEDOOR Without Track Top of the door should be level with the topHang the Opener Ihstallatiion StepBNSTALLATiON Step Outside Keylock Accessory ConnectionsUse tacks or staples to permanently attach entrapment Mounting If \1Install the Battery Backup UtNISTALLATilON StepDONOTusebulbs largerthan Ioow ONLYuseA19 sizebulbs MNSTALLATl!OH Step Attach the Emergency Release RopeHandle Elec*rical Requirements MNSTALLATmON Step tImportant Information about Safety Reversing Sensor Install The Protector System Safety SensorsGarage door track installation preferred Installing the BracketsWall installation Figures 2 Floor installation FigureMounting and Wiring the Safety Reversing Sensors Aligning the Safety Reversing SensorsTroubleshooting the Safety Reversing Sensors Fasten he Door Bracket Bnstallation Step tSectional Doors Wood DoorsGarage ONE-PIECE DoorsUNSTALLATmN Step Connect Door Arm to TrolleySectional Doors only Assemble the Door Arm Doora,desiredlll Adjustment StepSe**ing the Force Adjustment StepTest The Protector System s Safety Sensors Test the Safety Reversal SystemTest Repeat the tesLUsing Your Garage Door Opener Readandfollowallwarningsand InstructionsAlwayskeepgaragedoorproperlybalanced Lock feature Light featureAdditional feature when used with Button hand-heM remoteRemote Control Battery Maintenance ScheduleCare Of Your Opener Once a MonthOperating Instructions Battery BackupOrange LED Green LEDHaving a Problern? TroubHeshooting My lights will not turn off when door is openMy remotes will not activate the door My motor unit hums brieflyPossible RPM sensor failure. Unplug to reset Diagnostic CharfSymptom LED is not lit on door control Symptom RPM Sensor = Short travel 6-815-20 cmErase All Codes From Motor Unit Memory To Add or Reprogram a Hand.held Remote ControlButton 315 MHz7o Add, Reprograrn or Cange a Keyless EnEry PIN Using the Learn Button Using the Motion Detecting ControlInstallation Paris KEY PartDescription Motor Unit Assembly Parts KEY Part NO. noKEY Part Description 77020BOutside Quick Release Button Mini-Remote Control with SECURITY,I760CB 8808CB 8810CB 41A5281 Foot 3 m Rail ExtensionHotes Page OUR Large Service Organization Spans America Chamberlain Service is On Call

WD962KLD, WD962KD specifications

The Chamberlain WD962KD and WD962KLD are powerful garage door opener models designed to provide homeowners with advanced technology, convenience, and reliability. Both models come equipped with smart features that make them stand out in the market.

One of the primary features of the WD962KD and WD962KLD is the powerful 1.25 HP motor. This robust motor ensures that even the heaviest garage doors can be opened and closed smoothly without straining the system. The WD962KLD model, in particular, features a DC motor, which not only offers silent operation but also enhances energy efficiency.

Both garage door openers are equipped with Chamberlain's patented MAX Lift Power System. This innovative technology delivers optimal lifting force and steady performance, making the opening and closing cycle faster and more efficient. The models are compatible with various types of garage doors, including sectional, one-piece, and up-and-over doors, providing versatility to suit different homeowners' needs.

Security is a major concern for homeowners, and Chamberlain addresses this with its advanced security features. The WD962KD and WD962KLD come with the MYQ technology, allowing users to monitor and control their garage door from anywhere using their smartphones. The app notifies users about the door's status in real time, providing peace of mind.

Another essential characteristic is the built-in battery backup feature. This ensures that even during power outages, homeowners can still operate their garage doors without hassle. The WD962KLD model goes one step further with its integrated lighting system that illuminates the garage area, enhancing safety and visibility when entering or exiting.

Installation is made easy with the included Quick-Install bracket system, which simplifies the setup process. The smooth operation is further complemented by the silent operation chain drive, ensuring minimal noise during usage, which is perfect for homes that are attached to the garage.

Furthermore, both garage door openers come with remote controls featuring a range of up to 1500 feet, enabling users to open their garage door from a significant distance. The keypad entry system offers an added layer of convenience and security, allowing for keyless access.

In summary, the Chamberlain WD962KD and WD962KLD garage door openers combine advanced technologies and user-friendly features to deliver a premium experience. With robust motors, smart technology, enhanced security options, and easy installation, these models are an excellent choice for homeowners looking to upgrade their garage door systems.
Top Page Image Contents