Nilfisk-ALTO 05211F, 05220G, 05230F, 05231F, 05221F, 05220F, 05210G, 05210F manual Scrubtec 770

Page 49

			Nilﬁsk ALTO
			SCRUBTEC 770 / 784
			Squeegee Assembly 12/09
Item	Ref. No.	Qty	Description
	10803KL		Squeegee Asm.
1	25201B	2	Knob
2	34260B	1	Squeegee Gasket
3	81301A	2	Nut, 3/8-16 Jam SS
4	30048A	2	Wheel, Gide 4” Diam.
5	53185A	2	Ring, 3/8 ID Snap
6	60272B	1	Channel, Sq. Weldment
7	30058A	1	Spacer, Squeegee
8	30069L	1	Blade, Rear Linatex (STD)
[ ]	30557A	1	Blade-Rear Gum Rubber (OPT)
9	80280A	2	Nut, Squeegee,Backup
10	80011A	2	Screw, 3/8-16 x 3
11	60252A	1	Strap, Clamp Sq. Ret.
12	930086	2	Rivet, 3/16 x .450 Alum.
13	50835A	1	Latch, Sq. Clamp
14	30717L1	1	Blade, Front Linatex (STD)
[ ]	30091A	1	Blade-Front Urethane (OPT)
15	60254A	2	Bolt, Shoulder 5/16 x 2 ¼
16	30049B	4	Wheel, Squeegee
17	81104A	2	Nut, ¼ -20
18	60243A	2	Bracket, Sq. Wheel
19	60358A	2	Shim, Squeegee Wheel
20	980657	4	Washer, ¼ Lock
21	962720	4	Screw, ¼ -20 x ½ Hex

NOTE: When changing squeegee blades, it might be necessary to loosen screw #10; install and secure blades with clamp #13; then retighten screw #10. This will allow for different thickness.

Nilﬁsk ALTO Operator's Manual - SCRUBTEC 770 / 784 / 795

FORM NO. 70935A - 49 -

Image 49

Contents Read this Manual Operators ManualTable of Contents Operator Safety Instructions Operator Safety Instructions Machine Speciﬁcations IntroductionModel SpecificationsHow To Put The Machine In a Van Or Truck Procedures for TransportingSymbols Used on Symbols Used on Scrubtec 770, 78471017A use Charge / Battery Meter Solo See Figure #1, Item H1 Increase Brush Pressure Switch See Figure #1, Item DD a Machine Control Panel 770L, 784L & 795L K J H Display Screens for Scrubtec 770L, 784L, 795L Figure #4 Machine Controls & FeaturesHow To Install The Batteries HOW to Prepare the Machine for OPERA- TionBattery Maintenance HOW to Prepare the Machine for OperationFigure # How To Charge The BatteriesFigure #9 How To Remove The Brushes Or Pad DriversFigure #11 Reprogramming One TouchHow to Fill The Solution Tank How To Operate the Squeegee S Class models onlyHow to Clean a Floor How To Traverse MachineThese Maintenance Procedures Must Be Done Every Day How to Clean a Very Dirty FloorDo These Procedures When You Begin Your Work Period Figure #21 Do These Procedures When You End Your WorkFigure #25 Figure #24How To Adjust The Squeegee Maintenance For The SqueegeeAdjusting Squeegee Pressure Adjusting Squeegee TiltHow to Clean the Solution Line Adjusting Squeegee BladesHOW to Correct Problems in the Machine Scrubtec 770L / 784L / 795L WB Common Error Codes Form no a Nilﬁsk Alto Operators Manual Scrubtec 770 / 784 Section 31 30 29 Ref. No Qty Description Nilﬁsk Alto Scrubtec 770 / 784 Recovery Tank Assembly 12/09 Scrubtec 770 / 784 Form no a Nilﬁsk Alto Operators Manual Scrubtec 770 / 784 Electrical Panel Assembly / Solo Speed Controller 12/09 Form no a Nilﬁsk Alto Operators Manual Scrubtec 770 / 784 Scrubtec 770 S / 784 S / 795 S Form no a Nilﬁsk Alto Operators Manual Scrubtec 770 / 784 Electrical Panel Assembly Parts List 2/07 18A 920208 Nut, 1/4-20 962968 Screw, 10-24 x 1/2 40749A Form no a Nilﬁsk Alto Operators Manual Scrubtec 770 / 784 Scr 6-32 x Form no a Nilﬁsk Alto Operators Manual Scrubtec 770 / 784 Ref. No Qty Description Nilﬁsk Alto Scrubtec 770 Squeegee Assembly 12/09 Scrubtec 770 Scrubtec Squeegee Assembly 12/09 Ref. No Qty Description Nilﬁsk Alto Scrubtec 770 / 784 Traverse System Assembly 2/05 Ref. No Qty Description Nilﬁsk Alto Operators Manual Scrubtec 770 / 784 Nilﬁsk Alto Operators Manual Scrubtec 770 / 784 Nilﬁsk Alto Scrubtec 770 / 784 Brush Motor #45036A 2/05 Nilﬁsk Alto Operators Manual Scrubtec 770 / 784 Permanent Magnet Motor MFG. in USA Parking Brake Spare Parts PN 59116APAD Drivers BrushesNilﬁsk Alto Operators Manual Scrubtec 770 / 784 Form no a Nilﬁsk Alto Operators Manual Scrubtec 770 / 784 Electrical Schematic 9/05 Page Page Year of Affixing the CE marking Always use genuine Nilﬁsk Alto Parts for repair Nilﬁsk Alto Limited U.S. Warranty