GE GNPR48L, GNPR40L Advanced troubleshooting, Manual Indexing for Each Regeneration, Errors

Page 24

Advanced troubleshooting.

Manual Indexing for Each Regeneration

The control valve may be manually indexed to each regeneration position as follows:

1.Remove the control valve cover.

2.Press down on the top of the drive gear to disengage the cam gear. (See Step 1 in Start-Up Rinsing Procedure section.)

3.With the cam gear disengaged, rotate the cam gear counterclockwise to the various positions, using the same steps as the Start-Up Rinsing Procedure.

The control valve may also be operated in a fast mode for testing the control. To activate the fast mode, follow Steps 1 and 2 above to disengage the cam gear. When the cam gear is disengaged, it should be advanced slightly in a counterclockwise direction.

The switch will then activate the motor to cause the cam gear to advance through all the cycles in about 30 minutes. The control will not recognize a fast mode as a regeneration. Manual regenerations can be initiated only by pressing the manual regeneration switch on the face of the control.

Errors

This system continuously monitors itself and displays an error message if it detects something wrong.

When an error is detected, the display shows the letters “Err” with a number from 1 to 4. The table below lists Err numbers, a description of each error, the cause of the error and the solutions.

To clear the error from the display, press any button on the control. If the error still exists, the control will display the error message again after 30 seconds.

Error Detection Codes

Code

Description

Cause

Solution

Err 1

Electronics failure

Control settings need reprogramming

Press any key to load default values.

 

 

 

Refer to Programming the Control.

Err 2 Improper start of regeneration (limit switch open when it should be closed)

Valve cam gear has been manually

Press any key to clear the alarm.

rotated during a regeneration

(Alarm automatically clears at “TIME OF

 

REGEN”).

 

 

Valve cam gear has been manually

The control will turn the motor on and drive

rotated out of “service” position

the cam gear to the proper location.

 

 

Faulty motor

Replace motor assembly.

 

 

Motor wire disconnected

Make sure motor wire is fully connected to

 

control.

Faulty switch

Replace switch.

Err 3 Improper finish of regeneration (limit switch closed when it should be open)

Valve cam gear has been manually

The control will turn the motor on and

rotated out of “service” position

drive the cam gear to the proper location.

 

 

Faulty motor

Replace motor assembly.

 

 

Motor wire disconnected

Make sure motor wire is fully connected to

 

control.

Faulty switch

Replace switch.

Err 4 Improper control settings (one or more settings out of the allowable range)

One or more settings is out of the allowable range

See the Advanced Programming Parameters section on page 22 and Default Settings section on page 23.

24

Image 24
Contents Installation Instructions Write the model and serial numbers here Model #Serial # Safety Precautions Before Beginning Installation Important Installation RecommendationsWhere to Install the Softener Unpacking and InspectionPlan HOW YOU will Install Softener Optional 3-VALVE Bypass Installation IllustrationValve Bypass System Install Bypass Valve Before YOU BeginOperation Connect and RUN the Valve Drain Hose Drain HoseInstall Grounding Wire and Clamps Brine Tubing ConnectionBypass Valve is Optional Open Water Supply Advance the Control ValvePurge the System RUN the WaterConnect to Electrical Power Install 9V Battery for Battery Backup FeatureInjector Selection Water Pressure Injector Part NumberProgramming the Control SET Present Time of DAYTime of Regeneration Total Water HardnessSalt PER Regen and Capacity System Capacity Inputs Example Capacity x 1,000Error Codes Normal OperationManual Regeneration Sounds YOU will HearSanitizing Procedures SPECIFICATIONS/DIMENSIONSAbout the water softener system Cleaning the Injector and Screen Breaking a Salt BridgeGe.com Care and cleaning of the water softening system Cleaning Iron Out of the Water Softening SystemChecking the Salt Storage Level and Refilling However, you must keep the tank supplied with saltBefore you call for service… What To DoNo soft water Taken not plumbed to soft waterAfter installation Not using any saltAfter water softening System was installed Water feels slipperyBrown/yellow colored Water after installation Salty tasting orBrown/yellow Colored waterAdvanced programming and troubleshooting section Advanced Programming ParametersMinimum Units Parameter Description Range Increments Default Settings Required ParametersAdvanced troubleshooting ErrorsError Detection Codes Manual Indexing for Each RegenerationTroubleshooting Procedures Run out of soft water Between regenerationsScreen section Disc open. Replace if neededWhat To Do Flow diagrams Service PositionBrine Draw Position Refill PositionBackwash Position Valve Disc IdentificationFast Rinse Position Checking the brine draw and refill function Water meterControl valve diagram Systems diagram Parts List General Electric Parts CatalogWhat Is Not Covered Product not accessible to provide required serviceFor The Period We Will Replace Warrantor General Electric Company. Louisville, KYGE Water Softening System Warranty. For Customers in Canada One YearSchedule Service Parts and AccessoriesConsumer Support GE Appliances Website Real Life Design Studio