GE GNPR40L, GNPR48L installation instructions Connect and RUN the Valve Drain Hose

Page 7

Installation Instructions

3PLUMB “IN” AND “OUT” PIPES TO AND FROM SOFTENER

CAUTION: Observe all of the following cautions as you connect inlet and outlet plumbing. See Typical Installation Illustration.

• BE SURE INCOMING HARD WATER SUPPLY IS

DIRECTED TO THE SOFTENER VALVE INLET PORT.

If house water flow is from the right, use a

plumbing crossover as shown in Typical

Installation Illustration.

• With the softener in place, determine the

correct length of piping required to connect the

household plumbing to the 1″ copper adapter

on the softener. Test fit all connections.

NOTE: The softener must not support the home’s

plumbing in the vertical direction. Secure the

inlet and outlet pipes to the wall/ceiling using pipe

clamps or straps. Be certain the home’s plumbing

does not exert any force on the softener bypass.

• Remove softener from installation space.

• Disconnect copper adapters and union nuts from

bypass valve.

• Reconnect copper adapters with union nuts

and gaskets in place to home plumbing. Before

soldering adapters, slide union nuts and gasket

4CONNECT AND RUN THE VALVE DRAIN HOSE (CONT.)

•Locate the other end of the hose at a suitable drain point (floor drain, sump, laundry tub, etc.) that terminates at the sewer. Check and comply with local codes.

•Tie or wire the hose in place at the drain

point. High water pressure will cause it to whip during the back-wash and fast rinse cycles of

regeneration. Also provide an air gap of at least 1-1/2″between the end of the hose and the drain point. An air gap prevents possible siphoning of sewer water into the softener,

if the sewer should “back-up.”

The water softener will not work if water cannot exit this hose during regeneration.

•Elevating the drain hose may cause back pressure that could reduce the brine draw during regeneration. If raising the drain line overhead is required to get to the drain point, measure the inlet water pressure to the softener first. For inlet

pressures between 20 and 50 psi, do not raise higher than 8′ above the floor. For inlet pressure

above 50 psi, the drain line may be raised to a maximum height of 14′.

away from area being soldered. NOTE: Torch heat

will damage plastic parts.

• Support inlet and outlet plumbing in some manner

(use pipe hangers or clamps) to keep the weight

off of the valve fittings.

• Slide softener back into position.

• Make final connections to the bypass valve.

4 CONNECT AND RUN THE VALVE

DRAIN HOSE

• Check that drain port on valve body has white

tape on it. If not, apply Teflon Tape to threads

prior to installing the valve drain fitting.

Valve drain hose

Tie or wire hose in place

STANDPIPE

LAUNDRY TUB

SUMP

• Connect valve drain fitting to valve drain port.

Tighten connection with a wrench.

• Connect 1/2″ diameter drain hose (not provided)

to the valve drain fitting. Tighten connections with

wrench.

Valve drain hose connection

11⁄2″ air gap

FLOOR DRAIN

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Write the model and serial numbers here Model # Installation InstructionsSerial # Safety Precautions Important Installation Recommendations Before Beginning InstallationUnpacking and Inspection Where to Install the SoftenerOptional 3-VALVE Bypass Installation Illustration Plan HOW YOU will Install SoftenerValve Bypass System Before YOU Begin Install Bypass ValveOperation Drain Hose Connect and RUN the Valve Drain HoseBrine Tubing Connection Install Grounding Wire and ClampsRUN the Water Bypass Valve is Optional Open Water SupplyAdvance the Control Valve Purge the SystemWater Pressure Injector Part Number Connect to Electrical PowerInstall 9V Battery for Battery Backup Feature Injector SelectionSET Present Time of DAY Programming the ControlTotal Water Hardness Time of RegenerationSalt PER Regen and Capacity Example Capacity x 1,000 System Capacity InputsSounds YOU will Hear Error CodesNormal Operation Manual RegenerationSPECIFICATIONS/DIMENSIONS Sanitizing ProceduresAbout the water softener system Breaking a Salt Bridge Cleaning the Injector and ScreenGe.com However, you must keep the tank supplied with salt Care and cleaning of the water softening systemCleaning Iron Out of the Water Softening System Checking the Salt Storage Level and RefillingTaken not plumbed to soft water Before you call for service…What To Do No soft waterWater feels slippery After installationNot using any salt After water softening System was installedColored water Brown/yellow colored Water after installationSalty tasting or Brown/yellowAdvanced Programming Parameters Advanced programming and troubleshooting sectionMinimum Units Parameter Description Range Increments Required Parameters Default SettingsManual Indexing for Each Regeneration Advanced troubleshootingErrors Error Detection CodesTroubleshooting Procedures Disc open. Replace if needed Run out of soft waterBetween regenerations Screen sectionWhat To Do Refill Position Flow diagramsService Position Brine Draw PositionValve Disc Identification Backwash PositionFast Rinse Position Water meter Checking the brine draw and refill functionControl valve diagram Systems diagram General Electric Parts Catalog Parts ListWarrantor General Electric Company. Louisville, KY What Is Not CoveredProduct not accessible to provide required service For The Period We Will ReplaceOne Year GE Water Softening System Warranty. For Customers in CanadaReal Life Design Studio Schedule ServiceParts and Accessories Consumer Support GE Appliances Website
Top Page Image Contents