GE GXSF30H Connect to Electrical Power, Programming the Control, SET Present Time of DAY

Page 10

Installation Instructions

9 CONNECT TO ELECTRICAL POWER

To gain access to the transformer/power cord assembly, remove the salt hole cover from the softener. Unclip the tabs on the rear of the top cover and rotate the cover upward to remove. DO NOT PULL OR DISCONNECT WIRING.

•The softener works on 24 volt-60Hz electric power. The included transformer changes standard 120-volt AC house power to 24 volts.

Plug the transformer into a 120-volt outlet only. Be sure the outlet is always live so it can not be switched off by mistake.

•Replace the top cover.

•Replace the salt hole cover.

PROGRAMMING THE CONTROL

PROGRAMMING THE CONTROL

CONTROL SETTINGS REQUIRED upon installation and after an extended power outage.

NOTES:

•WHEN THE TRANSFORMER IS PLUGGED INTO THE ELECTRICAL OUTLET, 12:00 PM (flashing), and PRESENT TIME is displayed. Program the control as instructed below.

If - - - is flashing, use the UP button to set the correct model code as follows: F30 for

GXSF30H. If you pass by the correct code number, use the DOWN button. Then press the MODE button to accept the correct model.

•A “beep” sounds while pressing buttons for control programming. One beep signals a change in the control display. Repeated beeps mean the control will not accept a change from the button you have pressed, and you should select another button.

•To program the control, you will use the UP , DOWN and MODE buttons.

•Use the MODE button to select the desired control function.

10

SET PRESENT TIME OF DAY

1. Press the MODE button until PRESENT TIME appears in the display.

2. Press UP or DOWN button to set. The UP button advances the time; the DOWN button moves the time in reverse.

If the present time is between noon and midnight, be sure PM shows in the display. If the present time is between midnight and noon, be sure AM shows in the display.

NOTE: Each press of an UP or DOWN button changes the time by one minute. Holding the button changes the time at a rapid rate.

3.When the present time is correct, press MODE to accept.

SET WATER HARDNESS NUMBER

1. Press the MODE button until HARDNESS appears in the display.

2.Press UP or DOWN button

to set your water hardness number in the display. DOWN decreases the hardness value. UP increases the hardness value.

NOTE: Each press of a button changes the display by 1, between 1 and 25. Above 25, the display changes 5 at a time (25, 30, 35, etc.). Holding a button in changes the numbers at a rapid rate.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 7283918 215C1173P021 49-5017706-06 JR Safety InformationCare and Cleaning Write the model and serial numbers here Model #Safety Precautions Before Beginning Installation Important Installation RecommendationsUnpacking and Inspection Where to Install the SoftenerTransit Plan HOW YOU will Install the Softener Typical Installation IllustrationInstall Bypass Valve Before YOU BeginConnect and RUN the Valve Drain Hose Plumb in and OUT Pipes to and from SoftenerInstall the Brine Tank Connecting a Rigid Valve Drain TubeADD Water and Salt to the Brine Tank Install Grounding ClampWith salt SET Present Time of DAY Connect to Electrical PowerProgramming the Control SET Water Hardness NumberError Signals Optional Control SettingsSYSTEM/ELECTRONIC Diagnostics SET Recharge Starting TimeSPECIFICATIONS/DIMENSIONS Sanitizing Procedures19″ 471⁄2″ 411⁄4″ 16″ About the water softener system Cleaning the Nozzle and Venturi Assembly Breaking a Salt BridgeFeature/Service Automatic Electronic Diagnostics Feature Optional Recharge ControlsFeature Memory Normal Operation, Control DisplaysTo remove an error code 1. Unplug transformer Service Electronic Demand Time Features and ServiceService Timer/Softener, Service Checkout Procedure ERRIf the code was changed, make ALL the timer settings Open a Nearby Soft Water FaucetIf the water softening system does not draw brine, check Cleaning Iron Out of the Water Softening System Care and cleaning of the water softening systemChecking the Salt Storage Level and Refilling No soft water Before you call for service…What To Do Taken not plumbed to soft waterExcessive/high level Water in brine tankBrown/yellow Brown/yellow colored Water after installationSalty tasting or Colored water Resin beads showingParts list Parts list Parts catalog General Electric Parts CatalogSupport Screen For The Period We Will Replace What Is Not CoveredWarrantor General Electric Company. Louisville, KY Warrantor Mabe Canada INC GE Water Softening System Warranty. For Customers in CanadaFor The Period Of We Will Replace One YearDe agua Cuidado y limpieza Cómo limpiar la ensambladuraDe averías Advertencia Advertencia No use con aguaInstrucciones de instalación Recomendaciones Importantes Para LA InstalaciónHerramientas Y Materiales Necesarios Para LA Instalación Desempacado E InspecciónDonde Instalar EL Descalcificador Use la válvula de bypass incluida para instalarPlanifique LA Instalación DEL Descalcificador Ilustración DE Instalación NormalAntes DE Comenzar Instale LA Válvula DE BypassRetire el descalcificador del lugar de instalación Conecte LAS Tuberías QUE Entran Y Salen DEL DescalcificadorCont Salmuera Y LA MangueraCómo Conectar UN Tubo DE Drenaje DE Válvula Rígida Instale LA Abrazadera DE Tierra Programación DEL Control Conectar a LA Fuente EléctricaAjuste LA Hora DEL DÍA Eficiencia DE LA SAL Ajustes Opcionales DE ControlDEL Sistema Botones UP Down Para fijar laEn la fábrica se siguen los cuidados para mantener Procedimientos DE DesinfecciónNi infectarán su suministro de agua ni causarán que Sobre el sistema de descalcificación de agua Cómo romper un puente de sal Cómo limpiar la ensambladura de la boquilla y el Venturi Función Memoria Operación normal, Pantalla de controlFunción Controles opcionales de recargado Característica/Servicio Diagnóstico electrónico automáticoVisualizado Servicio Diagnóstico electrónico iniciado manualmente Abra UN Grifo DE Agua Descalcificada QUE Esté CercaServicio Inspección manual del avance de la recarga Cuidado y limpieza del sistema de descalcificación de agua PrecauciónAntes de llamar para solicitar servicio… Qué hacerConsejos para la identificación y solución de averías El agua sabe a sal o tiene Notas Ge.com Lista de partes Ge.com Catálogo de partes Catálogo DE Partes DE General ElectricInterruptor Por el período de Reemplazamos Garantía GE para el Sistema de Descalcificación de AguaLo que no está cubierto Garantías ampliadas Soporte al Consumidor Página Web de GE AppliancesSolicite una reparación Piezas y accesoriosConsumer Support GE Appliances Website Schedule ServiceParts and Accessories Real Life Design Studio

GXSF30H specifications

The GE GXSF30H is a highly regarded water filtration system designed to deliver clean, filtered water for residential use. This model features an advanced filtration process that effectively removes impurities and contaminants, ensuring that the water you drink is safe and refreshing. With its sleek design and efficient performance, the GXSF30H appeals to many homeowners looking for quality water solutions.

One of the key features of the GE GXSF30H is its high capacity. This water filtration system can treat up to 30,000 grains of hardness, making it suitable for families of various sizes. The generous capacity means that it requires less frequent maintenance and provides continuous access to soft water, enhancing your overall home experience.

The GXSF30H employs a modern ion-exchange technology that works by exchanging hard minerals like calcium and magnesium with sodium ions. This process effectively softens the water, reducing scale buildup in pipes and appliances, which can prolong their life and improve efficiency. As a result, homeowners save on energy costs associated with heating water and maintaining appliances.

Another standout characteristic of the GE GXSF30H is its user-friendly interface. The system features an intuitive digital control panel that provides real-time feedback on the system’s performance, making it easy to monitor water quality and system efficiency. This panel also includes diagnostic alerts to notify users when maintenance is needed, ensuring the system runs optimally at all times.

In terms of installation, the GE GXSF30H is designed for straightforward setup, compatible with most plumbing systems. It comes equipped with a comprehensive installation kit, allowing most homeowners to complete the installation without the need for professional assistance.

Finally, the GE GXSF30H is backed by a reputable brand known for quality and reliability. GE’s commitment to innovation means that the GXSF30H incorporates the latest technologies to meet consumer needs and environmental standards. This water filtration system offers not just functionality but also a long-term solution for ensuring clean and enjoyable water for everyday use. Whether you're concerned about hard water issues or simply desire better-tasting water, the GE GXSF30H is a solid investment for your home.
Top Page Image Contents