GE GXSF30H Before Beginning Installation, Important Installation Recommendations

Page 3

Installation Instructions

Water Softening System

Model GXSF30H

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

WARNING: Read entire manual. Failure to follow all guides and rules could cause personal injury or property damage.

•Check with your state and/or local public works department for plumbing codes. You must follow their guides as you install the Water Softening system.

NOTE: Failure to comply with these installation instructions will void the product warranty, and the installer will be responsible for any service, repair or damages caused thereby.

BEFORE BEGINNING INSTALLATION

Read these instructions completely and carefully.

•IMPORTANT — Save these instructions for local inspector’s use.

•IMPORTANT — Observe all governing codes and ordinances.

•Note to Installer – Be sure to leave these instructions with the Consumer.

•Note to Consumer – Keep these instructions for future reference.

•Proper installation is the responsibility of the installer.

•Product failure due to improper installation is not covered under the Warranty.

•A shutoff valve must be available or added near the installation point.

IMPORTANT INSTALLATION

RECOMMENDATIONS

•In the Commonwealth of Massachusetts, Plumbing Code 248 CMR shall be adhered to. Consult with your licensed plumber.

•Use only lead-free solder and flux for all sweat- solder connections, as required by state and federal codes.

•Connect the softener to the main water supply pipe before or ahead of the water heater.

DO NOT RUN HOT WATER THROUGH THE SOFTENER. Temperature of water passing through the softener must be less than 120°F.

IMPORTANT INSTALLATION

RECOMMENDATIONS (CONT.)

•Use care when handling the softener. Do not turn upside down, drop, drag or set on sharp protrusions.

•Maximum allowable inlet water pressure is 125 psi. If daytime pressure is over 80 psi, nighttime pressure may exceed the maximum. Use a pressure reducing valve if necessary. (Adding a pressure reducing valve may reduce the flow.)

•The softener works on 24 volt-60 Hz electrical power only. Be sure to use the included transformer. Be sure the electric outlet and transformer are in an inside location to protect from moisture.

•See Where to Install the Softener section for more details.

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. The water should be tested periodically to verify that the system is performing satisfactorily.

•Small parts remaining after the installation could be a choke hazard. Discard safely.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Write the model and serial numbers here Model # Safety InformationCare and Cleaning 7283918 215C1173P021 49-5017706-06 JRSafety Precautions Important Installation Recommendations Before Beginning InstallationWhere to Install the Softener Unpacking and InspectionTransit Typical Installation Illustration Plan HOW YOU will Install the SoftenerBefore YOU Begin Install Bypass ValvePlumb in and OUT Pipes to and from Softener Connect and RUN the Valve Drain HoseConnecting a Rigid Valve Drain Tube Install the Brine TankInstall Grounding Clamp ADD Water and Salt to the Brine TankWith salt SET Water Hardness Number Connect to Electrical PowerProgramming the Control SET Present Time of DAYSET Recharge Starting Time Optional Control SettingsSYSTEM/ELECTRONIC Diagnostics Error SignalsSanitizing Procedures SPECIFICATIONS/DIMENSIONS19″ 471⁄2″ 411⁄4″ 16″ About the water softener system Breaking a Salt Bridge Cleaning the Nozzle and Venturi AssemblyNormal Operation, Control Displays Feature Optional Recharge ControlsFeature Memory Feature/Service Automatic Electronic DiagnosticsERR Service Electronic Demand Time Features and ServiceService Timer/Softener, Service Checkout Procedure To remove an error code 1. Unplug transformerOpen a Nearby Soft Water Faucet If the code was changed, make ALL the timer settingsIf the water softening system does not draw brine, check Care and cleaning of the water softening system Cleaning Iron Out of the Water Softening SystemChecking the Salt Storage Level and Refilling Taken not plumbed to soft water Before you call for service…What To Do No soft waterWater in brine tank Excessive/high levelColored water Resin beads showing Brown/yellow colored Water after installationSalty tasting or Brown/yellowParts list Parts list General Electric Parts Catalog Parts catalogSupport Screen What Is Not Covered For The Period We Will ReplaceWarrantor General Electric Company. Louisville, KY One Year GE Water Softening System Warranty. For Customers in CanadaFor The Period Of We Will Replace Warrantor Mabe Canada INCCómo limpiar la ensambladura De agua Cuidado y limpiezaDe averías Advertencia No use con agua AdvertenciaRecomendaciones Importantes Para LA Instalación Instrucciones de instalaciónUse la válvula de bypass incluida para instalar Desempacado E InspecciónDonde Instalar EL Descalcificador Herramientas Y Materiales Necesarios Para LA InstalaciónIlustración DE Instalación Normal Planifique LA Instalación DEL DescalcificadorInstale LA Válvula DE Bypass Antes DE ComenzarConecte LAS Tuberías QUE Entran Y Salen DEL Descalcificador Retire el descalcificador del lugar de instalaciónSalmuera Y LA Manguera ContCómo Conectar UN Tubo DE Drenaje DE Válvula Rígida Instale LA Abrazadera DE Tierra Conectar a LA Fuente Eléctrica Programación DEL ControlAjuste LA Hora DEL DÍA Botones UP Down Para fijar la Ajustes Opcionales DE ControlDEL Sistema Eficiencia DE LA SALProcedimientos DE Desinfección En la fábrica se siguen los cuidados para mantenerNi infectarán su suministro de agua ni causarán que Sobre el sistema de descalcificación de agua Cómo romper un puente de sal Cómo limpiar la ensambladura de la boquilla y el Venturi Característica/Servicio Diagnóstico electrónico automático Operación normal, Pantalla de controlFunción Controles opcionales de recargado Función MemoriaVisualizado Abra UN Grifo DE Agua Descalcificada QUE Esté Cerca Servicio Diagnóstico electrónico iniciado manualmenteServicio Inspección manual del avance de la recarga Precaución Cuidado y limpieza del sistema de descalcificación de aguaQué hacer Antes de llamar para solicitar servicio…Consejos para la identificación y solución de averías El agua sabe a sal o tiene Notas Ge.com Lista de partes Ge.com Catálogo DE Partes DE General Electric Catálogo de partesInterruptor Garantía GE para el Sistema de Descalcificación de Agua Por el período de ReemplazamosLo que no está cubierto Piezas y accesorios Soporte al Consumidor Página Web de GE AppliancesSolicite una reparación Garantías ampliadasReal Life Design Studio Schedule ServiceParts and Accessories Consumer Support GE Appliances Website

GXSF30H specifications

The GE GXSF30H is a highly regarded water filtration system designed to deliver clean, filtered water for residential use. This model features an advanced filtration process that effectively removes impurities and contaminants, ensuring that the water you drink is safe and refreshing. With its sleek design and efficient performance, the GXSF30H appeals to many homeowners looking for quality water solutions.

One of the key features of the GE GXSF30H is its high capacity. This water filtration system can treat up to 30,000 grains of hardness, making it suitable for families of various sizes. The generous capacity means that it requires less frequent maintenance and provides continuous access to soft water, enhancing your overall home experience.

The GXSF30H employs a modern ion-exchange technology that works by exchanging hard minerals like calcium and magnesium with sodium ions. This process effectively softens the water, reducing scale buildup in pipes and appliances, which can prolong their life and improve efficiency. As a result, homeowners save on energy costs associated with heating water and maintaining appliances.

Another standout characteristic of the GE GXSF30H is its user-friendly interface. The system features an intuitive digital control panel that provides real-time feedback on the system’s performance, making it easy to monitor water quality and system efficiency. This panel also includes diagnostic alerts to notify users when maintenance is needed, ensuring the system runs optimally at all times.

In terms of installation, the GE GXSF30H is designed for straightforward setup, compatible with most plumbing systems. It comes equipped with a comprehensive installation kit, allowing most homeowners to complete the installation without the need for professional assistance.

Finally, the GE GXSF30H is backed by a reputable brand known for quality and reliability. GE’s commitment to innovation means that the GXSF30H incorporates the latest technologies to meet consumer needs and environmental standards. This water filtration system offers not just functionality but also a long-term solution for ensuring clean and enjoyable water for everyday use. Whether you're concerned about hard water issues or simply desire better-tasting water, the GE GXSF30H is a solid investment for your home.
Top Page Image Contents