GE GXSF30H installation instructions If the water softening system does not draw brine, check

Page 18

About the water softener system.

Service: Manually Advance Recharge Check

NOTE: The control display must show a steady time (not flashing).

1.Press the RECHARGE button and hold in for three seconds. RECHARGE NOW begins to flash as the water softening system enters the fill cycle of recharge. Remove the brinewell cover and, using a flashlight, observe fill water entering the brine tank. If water does not enter the tank, look for an obstructed nozzle, venturi, fill flow plug or brine tubing. See Care and Cleaning of the Water Softener System section.

2.After observing fill, press the RECHARGE button to move the water softening system into brining. A slow flow of water to the drain will begin. Verify brine draw from the brine tank by shining a flashlight into the brinewell and observing a noticeable drop in the liquid level over an extended period of time.

NOTE: Be sure a salt bridge is not preventing water from contacting salt. See Care and cleaning of the water softening system section.

If the water softening system does not draw brine, check:

■nozzle and/or venturi dirty or defective.

■defective nozzle and venturi seal.

■nozzle and venturi not seated properly on gasket.

■other inner valve defect (rotor seal, rotor and disc, wave washer, etc.).

■restricted drain (check drain fitting and hose).

NOTE: If water system pressure is low, an elevated drain hose may cause back pressure, stopping brine draw.

3.Again, press the RECHARGE button to move the water softening system into backwash. Look for a fast flow of water from the drain hose. A slow flow indicates a plugged top distributor, backwash flow plug or drain hose.

4.Press the RECHARGE button to move the water softening system into fast rinse. Again look for a fast drain flow. Allow the water softening system to rinse for a few minutes to flush out any brine that may remain in the resin tank from the brining cycle test.

5.To return the water softening system to service, press the RECHARGE button.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents 7283918 215C1173P021 49-5017706-06 JR Safety InformationCare and Cleaning Write the model and serial numbers here Model #Safety Precautions Before Beginning Installation Important Installation RecommendationsWhere to Install the Softener Unpacking and InspectionTransit Plan HOW YOU will Install the Softener Typical Installation IllustrationInstall Bypass Valve Before YOU BeginConnect and RUN the Valve Drain Hose Plumb in and OUT Pipes to and from SoftenerInstall the Brine Tank Connecting a Rigid Valve Drain TubeInstall Grounding Clamp ADD Water and Salt to the Brine TankWith salt SET Present Time of DAY Connect to Electrical PowerProgramming the Control SET Water Hardness NumberError Signals Optional Control SettingsSYSTEM/ELECTRONIC Diagnostics SET Recharge Starting TimeSanitizing Procedures SPECIFICATIONS/DIMENSIONS19″ 471⁄2″ 411⁄4″ 16″ About the water softener system Cleaning the Nozzle and Venturi Assembly Breaking a Salt BridgeFeature/Service Automatic Electronic Diagnostics Feature Optional Recharge ControlsFeature Memory Normal Operation, Control DisplaysTo remove an error code 1. Unplug transformer Service Electronic Demand Time Features and ServiceService Timer/Softener, Service Checkout Procedure ERRIf the code was changed, make ALL the timer settings Open a Nearby Soft Water FaucetIf the water softening system does not draw brine, check Care and cleaning of the water softening system Cleaning Iron Out of the Water Softening SystemChecking the Salt Storage Level and Refilling No soft water Before you call for service…What To Do Taken not plumbed to soft waterExcessive/high level Water in brine tankBrown/yellow Brown/yellow colored Water after installationSalty tasting or Colored water Resin beads showingParts list Parts list Parts catalog General Electric Parts CatalogSupport Screen What Is Not Covered For The Period We Will ReplaceWarrantor General Electric Company. Louisville, KY Warrantor Mabe Canada INC GE Water Softening System Warranty. For Customers in CanadaFor The Period Of We Will Replace One YearCómo limpiar la ensambladura De agua Cuidado y limpiezaDe averías Advertencia Advertencia No use con aguaInstrucciones de instalación Recomendaciones Importantes Para LA InstalaciónHerramientas Y Materiales Necesarios Para LA Instalación Desempacado E InspecciónDonde Instalar EL Descalcificador Use la válvula de bypass incluida para instalarPlanifique LA Instalación DEL Descalcificador Ilustración DE Instalación NormalAntes DE Comenzar Instale LA Válvula DE BypassRetire el descalcificador del lugar de instalación Conecte LAS Tuberías QUE Entran Y Salen DEL DescalcificadorSalmuera Y LA Manguera ContCómo Conectar UN Tubo DE Drenaje DE Válvula Rígida Instale LA Abrazadera DE Tierra Conectar a LA Fuente Eléctrica Programación DEL ControlAjuste LA Hora DEL DÍA Eficiencia DE LA SAL Ajustes Opcionales DE ControlDEL Sistema Botones UP Down Para fijar laProcedimientos DE Desinfección En la fábrica se siguen los cuidados para mantenerNi infectarán su suministro de agua ni causarán que Sobre el sistema de descalcificación de agua Cómo romper un puente de sal Cómo limpiar la ensambladura de la boquilla y el Venturi Función Memoria Operación normal, Pantalla de controlFunción Controles opcionales de recargado Característica/Servicio Diagnóstico electrónico automáticoVisualizado Servicio Diagnóstico electrónico iniciado manualmente Abra UN Grifo DE Agua Descalcificada QUE Esté CercaServicio Inspección manual del avance de la recarga Cuidado y limpieza del sistema de descalcificación de agua PrecauciónAntes de llamar para solicitar servicio… Qué hacerConsejos para la identificación y solución de averías El agua sabe a sal o tiene Notas Ge.com Lista de partes Ge.com Catálogo de partes Catálogo DE Partes DE General ElectricInterruptor Garantía GE para el Sistema de Descalcificación de Agua Por el período de ReemplazamosLo que no está cubierto Garantías ampliadas Soporte al Consumidor Página Web de GE AppliancesSolicite una reparación Piezas y accesoriosConsumer Support GE Appliances Website Schedule ServiceParts and Accessories Real Life Design Studio

GXSF30H specifications

The GE GXSF30H is a highly regarded water filtration system designed to deliver clean, filtered water for residential use. This model features an advanced filtration process that effectively removes impurities and contaminants, ensuring that the water you drink is safe and refreshing. With its sleek design and efficient performance, the GXSF30H appeals to many homeowners looking for quality water solutions.

One of the key features of the GE GXSF30H is its high capacity. This water filtration system can treat up to 30,000 grains of hardness, making it suitable for families of various sizes. The generous capacity means that it requires less frequent maintenance and provides continuous access to soft water, enhancing your overall home experience.

The GXSF30H employs a modern ion-exchange technology that works by exchanging hard minerals like calcium and magnesium with sodium ions. This process effectively softens the water, reducing scale buildup in pipes and appliances, which can prolong their life and improve efficiency. As a result, homeowners save on energy costs associated with heating water and maintaining appliances.

Another standout characteristic of the GE GXSF30H is its user-friendly interface. The system features an intuitive digital control panel that provides real-time feedback on the system’s performance, making it easy to monitor water quality and system efficiency. This panel also includes diagnostic alerts to notify users when maintenance is needed, ensuring the system runs optimally at all times.

In terms of installation, the GE GXSF30H is designed for straightforward setup, compatible with most plumbing systems. It comes equipped with a comprehensive installation kit, allowing most homeowners to complete the installation without the need for professional assistance.

Finally, the GE GXSF30H is backed by a reputable brand known for quality and reliability. GE’s commitment to innovation means that the GXSF30H incorporates the latest technologies to meet consumer needs and environmental standards. This water filtration system offers not just functionality but also a long-term solution for ensuring clean and enjoyable water for everyday use. Whether you're concerned about hard water issues or simply desire better-tasting water, the GE GXSF30H is a solid investment for your home.
Top Page Image Contents