GE GXSF30H SET Recharge Starting Time, Optional Control Settings, SYSTEM/ELECTRONIC Diagnostics

Page 11

Installation Instructions

SET WATER HARDNESS NUMBER (CONT.)

3.When the display shows your water hardness (in grains per gallon), press MODE to accept.

NOTE: If there is clear water iron in your water supply, you will need to increase the hardness setting by 5 for each 1 ppm of clear water iron in your water supply.

You can get the grains per gallon (gpg) hardness of your water supply from a water analysis laboratory. If you are on a municipal supply, call your local water department. Or call Legend Technical Services, an independent laboratory, to request a water hardness test kit at 1.800.949.8220, option 4. If your report shows hardness in parts per million (ppm) or milligrams per liter (mg/l), simply divide by 17.1 to get the equivalent number of grains per gallon.

SET RECHARGE (STARTING) TIME

1. Press the MODE button until RECHARGE TIME appears in the display.

NOTE: A flashing 2:00 AM (factory

default) should show in the display. This is a good time for recharge to start (takes about 2 hours) in most households because water is not in use. HARD WATER is bypassed to house faucets during recharge.

OPTIONAL CONTROL SETTINGS

The controller display has several options and features.

SYSTEM/ELECTRONIC DIAGNOSTICS

This display contains system

 

 

 

 

 

 

 

 

 

 

diagnostics information to assist in

 

 

 

 

 

troubleshooting problems with the

 

OR

Water Softener. See page 17.

 

 

 

 

 

 

 

 

 

 

To access the System Diagnostics, press and hold the MODE button for 3 seconds.

To return to the normal display, press the MODE button 2 times.

SALT EFFICIENCY

When the SALT EFFICIENCY feature is ON, the

unit will operate at a salt efficiency of at least 4000 grains of hardness removed per pound of salt. This mode of operation is the most efficient setting for salt usage, because the system will tend to recharge more often, with less salt usage. Turning the feature OFF will tend to lengthen the time between recharge cycles, which will provide the most efficient usage of water, but may use more salt. The degree of difference between these two cycles is highly dependent on the water usage and hardness

at a particular installation.

NOTE: California Regulations require this feature to be ON for installations in California.

If no change is needed, go to step 3. To change the recharge starting time, follow step 2.

2.Press UP or DOWN button to set the desired recharge start time. Be sure to observe the AM or PM as you did when setting the time of day.

NOTE: Each press of a button changes the time by

To access the Salt Efficiency, press and hold the MODE button for 3 seconds. The System Diagnostics display will appear.

Press the MODE button again and the Salt Efficiency display will appear.

DAYS TO EMPTY

E

HARDNESS

 

 

 

DAYS TO EMPTY

E

HARDNESS

 

 

 

1 hour. Holding the buttons in changes the time at a rapid rate.

3.Press the MODE button to accept.

11

To change the setting, press the

UP or DOWN buttons to toggle the feature ON or OFF. Press the MODE button to accept.

ERROR SIGNALS

If there is an error code detected, DAYS TO EMPTY the display will flash Err to signal that the softener requires service.

HARDNESS

See page 16 for information to

assist in troubleshooting error codes. Once the problem is corrected, disconnect the transformer from the wall outlet momentarily, and plug it back in. The normal display will appear. The motor may run for several minutes, as the unit resets. If the problem is not corrected, the error code will reappear in 6 minutes.

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Write the model and serial numbers here Model # Safety InformationCare and Cleaning 7283918 215C1173P021 49-5017706-06 JRSafety Precautions Important Installation Recommendations Before Beginning InstallationTransit Where to Install the SoftenerUnpacking and Inspection Typical Installation Illustration Plan HOW YOU will Install the SoftenerBefore YOU Begin Install Bypass ValvePlumb in and OUT Pipes to and from Softener Connect and RUN the Valve Drain HoseConnecting a Rigid Valve Drain Tube Install the Brine TankWith salt Install Grounding ClampADD Water and Salt to the Brine Tank SET Water Hardness Number Connect to Electrical PowerProgramming the Control SET Present Time of DAYSET Recharge Starting Time Optional Control SettingsSYSTEM/ELECTRONIC Diagnostics Error Signals19″ 471⁄2″ 411⁄4″ 16″ Sanitizing ProceduresSPECIFICATIONS/DIMENSIONS About the water softener system Breaking a Salt Bridge Cleaning the Nozzle and Venturi AssemblyNormal Operation, Control Displays Feature Optional Recharge ControlsFeature Memory Feature/Service Automatic Electronic DiagnosticsERR Service Electronic Demand Time Features and ServiceService Timer/Softener, Service Checkout Procedure To remove an error code 1. Unplug transformerOpen a Nearby Soft Water Faucet If the code was changed, make ALL the timer settingsIf the water softening system does not draw brine, check Checking the Salt Storage Level and Refilling Care and cleaning of the water softening systemCleaning Iron Out of the Water Softening System Taken not plumbed to soft water Before you call for service…What To Do No soft waterWater in brine tank Excessive/high levelColored water Resin beads showing Brown/yellow colored Water after installationSalty tasting or Brown/yellowParts list Parts list General Electric Parts Catalog Parts catalogSupport Screen Warrantor General Electric Company. Louisville, KY What Is Not CoveredFor The Period We Will Replace One Year GE Water Softening System Warranty. For Customers in CanadaFor The Period Of We Will Replace Warrantor Mabe Canada INCDe averías Cómo limpiar la ensambladuraDe agua Cuidado y limpieza Advertencia No use con agua AdvertenciaRecomendaciones Importantes Para LA Instalación Instrucciones de instalaciónUse la válvula de bypass incluida para instalar Desempacado E InspecciónDonde Instalar EL Descalcificador Herramientas Y Materiales Necesarios Para LA InstalaciónIlustración DE Instalación Normal Planifique LA Instalación DEL DescalcificadorInstale LA Válvula DE Bypass Antes DE ComenzarConecte LAS Tuberías QUE Entran Y Salen DEL Descalcificador Retire el descalcificador del lugar de instalaciónCómo Conectar UN Tubo DE Drenaje DE Válvula Rígida Salmuera Y LA MangueraCont Instale LA Abrazadera DE Tierra Ajuste LA Hora DEL DÍA Conectar a LA Fuente EléctricaProgramación DEL Control Botones UP Down Para fijar la Ajustes Opcionales DE ControlDEL Sistema Eficiencia DE LA SALNi infectarán su suministro de agua ni causarán que Procedimientos DE DesinfecciónEn la fábrica se siguen los cuidados para mantener Sobre el sistema de descalcificación de agua Cómo romper un puente de sal Cómo limpiar la ensambladura de la boquilla y el Venturi Característica/Servicio Diagnóstico electrónico automático Operación normal, Pantalla de controlFunción Controles opcionales de recargado Función MemoriaVisualizado Abra UN Grifo DE Agua Descalcificada QUE Esté Cerca Servicio Diagnóstico electrónico iniciado manualmenteServicio Inspección manual del avance de la recarga Precaución Cuidado y limpieza del sistema de descalcificación de aguaQué hacer Antes de llamar para solicitar servicio…Consejos para la identificación y solución de averías El agua sabe a sal o tiene Notas Ge.com Lista de partes Ge.com Catálogo DE Partes DE General Electric Catálogo de partesInterruptor Lo que no está cubierto Garantía GE para el Sistema de Descalcificación de AguaPor el período de Reemplazamos Piezas y accesorios Soporte al Consumidor Página Web de GE AppliancesSolicite una reparación Garantías ampliadasReal Life Design Studio Schedule ServiceParts and Accessories Consumer Support GE Appliances Website

GXSF30H specifications

The GE GXSF30H is a highly regarded water filtration system designed to deliver clean, filtered water for residential use. This model features an advanced filtration process that effectively removes impurities and contaminants, ensuring that the water you drink is safe and refreshing. With its sleek design and efficient performance, the GXSF30H appeals to many homeowners looking for quality water solutions.

One of the key features of the GE GXSF30H is its high capacity. This water filtration system can treat up to 30,000 grains of hardness, making it suitable for families of various sizes. The generous capacity means that it requires less frequent maintenance and provides continuous access to soft water, enhancing your overall home experience.

The GXSF30H employs a modern ion-exchange technology that works by exchanging hard minerals like calcium and magnesium with sodium ions. This process effectively softens the water, reducing scale buildup in pipes and appliances, which can prolong their life and improve efficiency. As a result, homeowners save on energy costs associated with heating water and maintaining appliances.

Another standout characteristic of the GE GXSF30H is its user-friendly interface. The system features an intuitive digital control panel that provides real-time feedback on the system’s performance, making it easy to monitor water quality and system efficiency. This panel also includes diagnostic alerts to notify users when maintenance is needed, ensuring the system runs optimally at all times.

In terms of installation, the GE GXSF30H is designed for straightforward setup, compatible with most plumbing systems. It comes equipped with a comprehensive installation kit, allowing most homeowners to complete the installation without the need for professional assistance.

Finally, the GE GXSF30H is backed by a reputable brand known for quality and reliability. GE’s commitment to innovation means that the GXSF30H incorporates the latest technologies to meet consumer needs and environmental standards. This water filtration system offers not just functionality but also a long-term solution for ensuring clean and enjoyable water for everyday use. Whether you're concerned about hard water issues or simply desire better-tasting water, the GE GXSF30H is a solid investment for your home.
Top Page Image Contents