Brother CS6000I operation manual Foot controller, Changing the needle stop position

Page 11

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————

Foot controller

Insert the foot controller plug into its jack/socket on the rear side of the sewing machine.

aFoot controller jack/socket

CAUTION

●When connecting the foot controller, be sure to turn off the sewing machine in order to prevent the machine from accidentally being started.

When you press the foot controller down lightly, the machine will run at a low speed. When you press harder, the machine’s speed will increase. When you take your foot off the foot controller, the machine will stop.

Slower

Faster

You should make sure that nothing is placed on the foot controller when the machine is not in use.

CAUTION

●Do not allow pieces of cloth and dust to build up on the foot controller. Doing so could cause a fire or an electric shock.

Note

●When the foot controller is plugged in, the start/stop button cannot be used to start or stop sewing (only for models equipped with the start/stop button).

Sewing speed controller (for models equipped with the start/stop button)

aSlide the sewing speed controller to the left or right to select the desired sewing speed. Slide the sewing speed controller to the left to sew at a slower speed, or slide the speed controller to the right to sew at a faster speed.

aSewing speed controller

•The speed set using the sewing speed controller is the foot controller’s maximum sewing speed.

Changing the needle stop position

Normally, the sewing machine is set to leave the needle in the fabric when sewing is stopped. Instead, the machine can be set to leave the needle raised when sewing is stopped.

aTurn off the sewing machine.

bHold down the “–” side of (stitch selection key) on the left and turn on the sewing machine.

After turning on the sewing machine, release the “–” side of (stitch selection key).

XThe needle stop position changes to the raised position.

Memo

•Perform the same operation to change the needle stop position to the lowered position.

10

Image 11

Contents Computerized Sewing Machine For Users in the UK, EIRE, Malta and Cyprus only For safe operation For a longer service lifeContents Utility Stitches Main parts Names of Machine Parts and Their FunctionsButtons provided on some models Needle and presser foot sectionOperation buttons ASlideopen theit. flat bed attachment to the left to Operation panelFlat bed attachment Optional accessories AccessoriesCTo turn off the machine, set the main power switch to Using Your Sewing MachinePower supply precautions BSet the main power switch toChanging the needle stop position Foot controllerETurn on the sewing machine Threading the MachineWinding the bobbin Pass the thread around the pre-tension diskGTrim the excess thread above the bobbin CSlide the bobbin winder shaft to the right For models equipped with the fast bobbin winding systemActual size 11.5mm 7/16 inch This model Lower threadingFor models equipped with the quick-set bobbin Right side see arrow b until the cover clicks into placeUpper threading Thread take-up lever Catch the thread on the hook as shown below DFully lower the needle threader leverLightly hold the end of the upper thread Drawing up the lower threadFor models equipped with the quick-set bobbin Fabrics Needle precautionsReplacing the Needle Needle types and their usesIncorrect needle Checking the needleReplacing the needle Correct needleInstalling the needle clamp Twin needle threading Sewing with a twin needleMark on the wheel points up. With models Replacing the Presser FootReplacing the presser foot Remove the presser foot Removing the presser foot holderRemoving the presser foot holder Attaching the presser foot holderSewing General sewing procedureCAttach the presser foot DIfwidth.necessary, adjust the stitch lengthSelecting stitching Turn on the sewing machineBRaise the presser foot lever Starting to sewOn the wheel points up. With models equipped Upper tension is too tight Thread tensionSewing reinforcement stitches Correct tensionSewing curves Useful Sewing TipsTrial sewing Changing the sewing directionSlide the flat bed attachment to the left to release it Using a free-arm styleSewing thin fabrics Sewing stretch fabricsAttach overcasting foot G or zigzag foot J Select a stitch Overcasting StitchesChanging the needle position When sewing is finished, cut the threadBasic Stitching Basic stitchingIf the needle does not catch the hem fold Blind HEM StitchingBAttach blind hem foot R CSelect a stitch Buttonholes can be sewn and buttons can be sewn on Buttonhole SewingIf the button does not fit in the button guide plate Size of the buttonhole is setFPullpossible.down the buttonhole lever as far as CAttach presser foot M Button sewingSewing buttonholes on stretch fabrics With stitch Select stitch ESelect a stitchRev. Reverse Zipper InsertionElastic attaching Sewing Stretch Fabrics and Elastic TapeStretch stitching Appliqués APPLIQUÉ, Patchwork and Quilt StitchingPiecing Patchwork crazy quilt stitchingDSelect stitch , or Using the optional quilting guideQuilting Baste the fabric to be quiltedGAfter sewing is finished, slide the feed dog Free-motion quiltingAttach zigzag foot J Select stitch Start sewing Reinforcement StitchingTriple stretch stitching Bar tack stitchingPullpossible.down the buttonhole lever as far as Once sewing is completed,Decorative Stitching DTrim along the stitches FagotingScallop stitching DPull the bobbin threads to create gathers SmockingShell tuck stitching Sew parallel stitching at intervals of 1 cm 3/8 inchUnfold the fabric, and then iron the tucks down to one side JoiningHeirloom stitching Utility stitches Stitch SettingsRfc. Reinforcement Pattern No Rfc Binding Appendix Cleaning the bobbin case MaintenanceCleaning the machine surface Remove the bobbin case Troubleshooting Fabric is LowerOr breaks Thread tenPitched noise While sewing Stitches areSkipped There is a highOperation beep for models equipped with the operation beep Error MessagesNumerics Index30, 32 English 885-S33/S34/S36/S37 XC8835-4216