Brother CS6000I operation manual Right side see arrow b until the cover clicks into place

Page 16

the right side (see arrow b) until the cover clicks into place.

•Replace the cover so that the end of the thread comes out from the left side of the cover (as shown by the line in the diagram).

■For models equipped with the quick-set bobbin

aRaise the needle to its highest position by turning the handwheel toward you (counterclockwise) or press (needle position button) (for models equipped with the needle position button), and raise the presser foot lever.

bSlide the button and open the cover.

1 2

aCover

bSlide button

cPut the bobbin in, feed the end of the thread through the slit, and then pull the thread to cut it.

•Only use bobbins that were designed to be used with this machine.

CAUTION

●Make sure you set the bobbin so the thread unrolls in the right direction. If the thread unrolls in the wrong direction, it may cause the thread tension to be incorrect or break the needle.

1

aCutter

•Make sure that the thread is correctly inserted through the tension-adjusting spring of the bobbin case. If it is not inserted, re- insert the thread.

1

1

aTension-adjusting spring

Memo

●The order that the bobbin thread should be passed through the bobbin case is indicated by marks around the bobbin case. Be sure to thread the machine as indicated.

dReplace the bobbin cover. Put the left tab in place (see arrow a), and then press lightly on the right side (see arrow b) until the cover clicks into place.

Memo

●You can begin sewing immediately without drawing up the bobbin thread. If you want to draw up the bobbin thread before you start to sew, follow to the procedure in “Drawing up the lower thread” (page 19).

15

Image 16

Contents Computerized Sewing Machine For Users in the UK, EIRE, Malta and Cyprus only For a longer service life For safe operationContents Utility Stitches Names of Machine Parts and Their Functions Main partsOperation buttons Needle and presser foot sectionButtons provided on some models Flat bed attachment Operation panelASlideopen theit. flat bed attachment to the left to Accessories Optional accessoriesUsing Your Sewing Machine Power supply precautionsBSet the main power switch to CTo turn off the machine, set the main power switch toFoot controller Changing the needle stop positionThreading the Machine Winding the bobbinPass the thread around the pre-tension disk ETurn on the sewing machineGTrim the excess thread above the bobbin For models equipped with the fast bobbin winding system CSlide the bobbin winder shaft to the rightLower threading Actual size 11.5mm 7/16 inch This modelRight side see arrow b until the cover clicks into place For models equipped with the quick-set bobbinUpper threading Thread take-up lever DFully lower the needle threader lever Catch the thread on the hook as shown belowFor models equipped with the quick-set bobbin Drawing up the lower threadLightly hold the end of the upper thread Needle precautions Replacing the NeedleNeedle types and their uses FabricsChecking the needle Replacing the needleCorrect needle Incorrect needleInstalling the needle clamp Sewing with a twin needle Twin needle threadingReplacing the presser foot Replacing the Presser FootMark on the wheel points up. With models Removing the presser foot holder Removing the presser foot holderAttaching the presser foot holder Remove the presser footGeneral sewing procedure SewingDIfwidth.necessary, adjust the stitch length Selecting stitchingTurn on the sewing machine CAttach the presser footOn the wheel points up. With models equipped Starting to sewBRaise the presser foot lever Thread tension Sewing reinforcement stitchesCorrect tension Upper tension is too tightUseful Sewing Tips Trial sewingChanging the sewing direction Sewing curvesUsing a free-arm style Sewing thin fabricsSewing stretch fabrics Slide the flat bed attachment to the left to release itOvercasting Stitches Attach overcasting foot G or zigzag foot J Select a stitchWhen sewing is finished, cut the thread Basic StitchingBasic stitching Changing the needle positionBAttach blind hem foot R CSelect a stitch Blind HEM StitchingIf the needle does not catch the hem fold Buttonhole Sewing Buttonholes can be sewn and buttons can be sewn onSize of the buttonhole is set If the button does not fit in the button guide plateFPullpossible.down the buttonhole lever as far as Sewing buttonholes on stretch fabrics Button sewingCAttach presser foot M ESelect a stitch With stitch Select stitchZipper Insertion Rev. ReverseStretch stitching Sewing Stretch Fabrics and Elastic TapeElastic attaching APPLIQUÉ, Patchwork and Quilt Stitching AppliquésPatchwork crazy quilt stitching PiecingUsing the optional quilting guide QuiltingBaste the fabric to be quilted DSelect stitch , orFree-motion quilting GAfter sewing is finished, slide the feed dogReinforcement Stitching Triple stretch stitchingBar tack stitching Attach zigzag foot J Select stitch Start sewingOnce sewing is completed, Pullpossible.down the buttonhole lever as far asDecorative Stitching Scallop stitching FagotingDTrim along the stitches Smocking Shell tuck stitchingSew parallel stitching at intervals of 1 cm 3/8 inch DPull the bobbin threads to create gathersHeirloom stitching JoiningUnfold the fabric, and then iron the tucks down to one side Stitch Settings Utility stitchesRfc. Reinforcement Pattern No Rfc Binding Appendix Cleaning the machine surface MaintenanceCleaning the bobbin case Remove the bobbin case Troubleshooting Lower Or breaksThread ten Fabric isStitches are SkippedThere is a high Pitched noise While sewingError Messages Operation beep for models equipped with the operation beepIndex Numerics30, 32 English 885-S33/S34/S36/S37 XC8835-4216